Flanged bearings: ring flanges vs flanged housing units

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Square flange side L

86 mm

Bolt-centre spacing J

64 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Source axial dimension A2

15 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Square flange side L

95 mm

Bolt-centre spacing J

70 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Source axial dimension A2

16 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Square flange side L

95 mm

Bolt-centre spacing J

70 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Source axial dimension A2

16 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Square flange side L

95 mm

Bolt-centre spacing J

70 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Source axial dimension A2

16 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Square flange side L

95 mm

Bolt-centre spacing J

70 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Source axial dimension A2

16 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Square flange side L

108 mm

Bolt-centre spacing J

83 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Source axial dimension A2

18 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Square flange side L

108 mm

Bolt-centre spacing J

83 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Source axial dimension A2

18 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Square flange side L

108 mm

Bolt-centre spacing J

83 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Source axial dimension A2

18 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Square flange side L

108 mm

Bolt-centre spacing J

83 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Source axial dimension A2

18 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Square flange side L

117 mm

Bolt-centre spacing J

92 mm

Flange thickness A1

15 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Source axial dimension A2

19 mm

Mounting hole diameter N

14 mm

Catalogue mounting bolt

M12

Shared catalogue mass

1.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Square flange side L

117 mm

Bolt-centre spacing J

92 mm

Flange thickness A1

15 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Source axial dimension A2

19 mm

Mounting hole diameter N

14 mm

Catalogue mounting bolt

M12

Shared catalogue mass

1.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Square flange side L

117 mm

Bolt-centre spacing J

92 mm

Flange thickness A1

15 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Source axial dimension A2

19 mm

Mounting hole diameter N

14 mm

Catalogue mounting bolt

M12

Shared catalogue mass

1.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Square flange side L

117 mm

Bolt-centre spacing J

92 mm

Flange thickness A1

15 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Source axial dimension A2

19 mm

Mounting hole diameter N

14 mm

Catalogue mounting bolt

M12

Shared catalogue mass

1.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Square flange side L

117 mm

Bolt-centre spacing J

92 mm

Flange thickness A1

15 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Source axial dimension A2

19 mm

Mounting hole diameter N

14 mm

Catalogue mounting bolt

M12

Shared catalogue mass

1.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Square flange side L

130 mm

Bolt-centre spacing J

102 mm

Flange thickness A1

15 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

21 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Square flange side L

130 mm

Bolt-centre spacing J

102 mm

Flange thickness A1

15 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

21 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Square flange side L

130 mm

Bolt-centre spacing J

102 mm

Flange thickness A1

15 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

21 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Square flange side L

137 mm

Bolt-centre spacing J

105 mm

Flange thickness A1

16 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Square flange side L

137 mm

Bolt-centre spacing J

105 mm

Flange thickness A1

16 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Square flange side L

137 mm

Bolt-centre spacing J

105 mm

Flange thickness A1

16 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Square flange side L

137 mm

Bolt-centre spacing J

105 mm

Flange thickness A1

16 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 22. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Square flange side L

143 mm

Bolt-centre spacing J

111 mm

Flange thickness A1

16 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Square flange side L

143 mm

Bolt-centre spacing J

111 mm

Flange thickness A1

16 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Square flange side L

143 mm

Bolt-centre spacing J

111 mm

Flange thickness A1

16 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Square flange side L

143 mm

Bolt-centre spacing J

111 mm

Flange thickness A1

16 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Source axial dimension A2

22 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

2.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Square flange side L

162 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Source axial dimension A2

25 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Square flange side L

162 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Source axial dimension A2

25 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Square flange side L

162 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Source axial dimension A2

25 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Square flange side L

162 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Source axial dimension A2

25 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Square flange side L

175 mm

Bolt-centre spacing J

143 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

29 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Square flange side L

175 mm

Bolt-centre spacing J

143 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

29 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Square flange side L

175 mm

Bolt-centre spacing J

143 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

29 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Square flange side L

175 mm

Bolt-centre spacing J

143 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

29 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

57.2 kN

Basic static rating C0r

40.1 kN

Square flange side L

187 mm

Bolt-centre spacing J

149 mm

Flange thickness A1

22 mm

Housing depth A

50 mm

Overall axial projection A0

69.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

30 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

5.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

57.2 kN

Basic static rating C0r

40.1 kN

Square flange side L

187 mm

Bolt-centre spacing J

149 mm

Flange thickness A1

22 mm

Housing depth A

50 mm

Overall axial projection A0

69.7 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Source axial dimension A2

30 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

5.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

62.2 kN

Basic static rating C0r

44.1 kN

Square flange side L

193 mm

Bolt-centre spacing J

152 mm

Flange thickness A1

22 mm

Housing depth A

54 mm

Overall axial projection A0

75.4 mm

Insert centre-to-face S

30.2 mm

Insert inner-ring width B

74.6 mm

Source axial dimension A2

31 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

5.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

62.2 kN

Basic static rating C0r

44.1 kN

Square flange side L

193 mm

Bolt-centre spacing J

152 mm

Flange thickness A1

22 mm

Housing depth A

54 mm

Overall axial projection A0

75.4 mm

Insert centre-to-face S

30.2 mm

Insert inner-ring width B

74.6 mm

Source axial dimension A2

31 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

5.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Square flange side L

200 mm

Bolt-centre spacing J

159 mm

Flange thickness A1

22 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Source axial dimension A2

34 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Square flange side L

200 mm

Bolt-centre spacing J

159 mm

Flange thickness A1

22 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Source axial dimension A2

34 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Square flange side L

200 mm

Bolt-centre spacing J

159 mm

Flange thickness A1

22 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Source axial dimension A2

34 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

72.7 kN

Basic static rating C0r

53.0 kN

Square flange side L

208 mm

Bolt-centre spacing J

165 mm

Flange thickness A1

22 mm

Housing depth A

58 mm

Overall axial projection A0

83.3 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

82.6 mm

Source axial dimension A2

34 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

7.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

72.7 kN

Basic static rating C0r

53.0 kN

Square flange side L

208 mm

Bolt-centre spacing J

165 mm

Flange thickness A1

22 mm

Housing depth A

58 mm

Overall axial projection A0

83.3 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

82.6 mm

Source axial dimension A2

34 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

7.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

84.0 kN

Basic static rating C0r

61.9 kN

Square flange side L

220 mm

Bolt-centre spacing J

175 mm

Flange thickness A1

24 mm

Housing depth A

63 mm

Overall axial projection A0

87.6 mm

Insert centre-to-face S

34.1 mm

Insert inner-ring width B

85.7 mm

Source axial dimension A2

36 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

8.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

84.0 kN

Basic static rating C0r

61.9 kN

Square flange side L

220 mm

Bolt-centre spacing J

175 mm

Flange thickness A1

24 mm

Housing depth A

63 mm

Overall axial projection A0

87.6 mm

Insert centre-to-face S

34.1 mm

Insert inner-ring width B

85.7 mm

Source axial dimension A2

36 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

8.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

96.1 kN

Basic static rating C0r

71.5 kN

Square flange side L

235 mm

Bolt-centre spacing J

187 mm

Flange thickness A1

25 mm

Housing depth A

68 mm

Overall axial projection A0

96.3 mm

Insert centre-to-face S

39.7 mm

Insert inner-ring width B

96.0 mm

Source axial dimension A2

40 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

11.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

96.1 kN

Basic static rating C0r

71.5 kN

Square flange side L

235 mm

Bolt-centre spacing J

187 mm

Flange thickness A1

25 mm

Housing depth A

68 mm

Overall axial projection A0

96.3 mm

Insert centre-to-face S

39.7 mm

Insert inner-ring width B

96.0 mm

Source axial dimension A2

40 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

11.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is the horizontal and vertical hole-centre spacing on the square flange, not its diagonal. L is the flange side; B is insert width. UCF-204 markings retain the spelling printed in this catalogue.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 23. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

12.8 kN

Basic static rating C0r

6.7 kN

Overall flange length H

113 mm

Bolt-centre spacing J

90 mm

Flange thickness A1

11 mm

Housing depth A

25.5 mm

Overall axial projection A0

33.3 mm

Flange transverse width L

60 mm

Source axial dimension A2

15 mm

Insert centre-to-face S

12.7 mm

Insert inner-ring width B

31.0 mm

Mounting hole diameter N

12 mm

Catalogue mounting bolt

M10

Shared catalogue mass

0.5 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Overall flange length H

130 mm

Bolt-centre spacing J

99 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Flange transverse width L

68 mm

Source axial dimension A2

16 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Overall flange length H

130 mm

Bolt-centre spacing J

99 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Flange transverse width L

68 mm

Source axial dimension A2

16 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Overall flange length H

130 mm

Bolt-centre spacing J

99 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Flange transverse width L

68 mm

Source axial dimension A2

16 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

14.0 kN

Basic static rating C0r

7.9 kN

Overall flange length H

130 mm

Bolt-centre spacing J

99 mm

Flange thickness A1

13 mm

Housing depth A

27 mm

Overall axial projection A0

35.8 mm

Flange transverse width L

68 mm

Source axial dimension A2

16 mm

Insert centre-to-face S

14.3 mm

Insert inner-ring width B

34.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Overall flange length H

148 mm

Bolt-centre spacing J

117 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Flange transverse width L

80 mm

Source axial dimension A2

18 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.0 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Overall flange length H

148 mm

Bolt-centre spacing J

117 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Flange transverse width L

80 mm

Source axial dimension A2

18 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.0 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Overall flange length H

148 mm

Bolt-centre spacing J

117 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Flange transverse width L

80 mm

Source axial dimension A2

18 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.0 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

19.5 kN

Basic static rating C0r

11.3 kN

Overall flange length H

148 mm

Bolt-centre spacing J

117 mm

Flange thickness A1

13 mm

Housing depth A

31 mm

Overall axial projection A0

40.2 mm

Flange transverse width L

80 mm

Source axial dimension A2

18 mm

Insert centre-to-face S

15.9 mm

Insert inner-ring width B

38.1 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.0 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Overall flange length H

161 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

14 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Flange transverse width L

90 mm

Source axial dimension A2

19 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Overall flange length H

161 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

14 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Flange transverse width L

90 mm

Source axial dimension A2

19 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Overall flange length H

161 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

14 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Flange transverse width L

90 mm

Source axial dimension A2

19 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Overall flange length H

161 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

14 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Flange transverse width L

90 mm

Source axial dimension A2

19 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

25.7 kN

Basic static rating C0r

15.4 kN

Overall flange length H

161 mm

Bolt-centre spacing J

130 mm

Flange thickness A1

14 mm

Housing depth A

34 mm

Overall axial projection A0

44.4 mm

Flange transverse width L

90 mm

Source axial dimension A2

19 mm

Insert centre-to-face S

17.5 mm

Insert inner-ring width B

42.9 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Overall flange length H

175 mm

Bolt-centre spacing J

144 mm

Flange thickness A1

14 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Flange transverse width L

100 mm

Source axial dimension A2

21 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Overall flange length H

175 mm

Bolt-centre spacing J

144 mm

Flange thickness A1

14 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Flange transverse width L

100 mm

Source axial dimension A2

21 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

29.1 kN

Basic static rating C0r

17.8 kN

Overall flange length H

175 mm

Bolt-centre spacing J

144 mm

Flange thickness A1

14 mm

Housing depth A

36 mm

Overall axial projection A0

51.2 mm

Flange transverse width L

100 mm

Source axial dimension A2

21 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

16 mm

Catalogue mounting bolt

M14

Shared catalogue mass

1.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Overall flange length H

188 mm

Bolt-centre spacing J

148 mm

Flange thickness A1

15 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Flange transverse width L

108 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Overall flange length H

188 mm

Bolt-centre spacing J

148 mm

Flange thickness A1

15 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Flange transverse width L

108 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Overall flange length H

188 mm

Bolt-centre spacing J

148 mm

Flange thickness A1

15 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Flange transverse width L

108 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

34.1 kN

Basic static rating C0r

21.3 kN

Overall flange length H

188 mm

Bolt-centre spacing J

148 mm

Flange thickness A1

15 mm

Housing depth A

38 mm

Overall axial projection A0

52.2 mm

Flange transverse width L

108 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

49.2 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

1.9 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 24. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Overall flange length H

197 mm

Bolt-centre spacing J

157 mm

Flange thickness A1

15 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Flange transverse width L

115 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Overall flange length H

197 mm

Bolt-centre spacing J

157 mm

Flange thickness A1

15 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Flange transverse width L

115 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Overall flange length H

197 mm

Bolt-centre spacing J

157 mm

Flange thickness A1

15 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Flange transverse width L

115 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

35.1 kN

Basic static rating C0r

23.3 kN

Overall flange length H

197 mm

Bolt-centre spacing J

157 mm

Flange thickness A1

15 mm

Housing depth A

40 mm

Overall axial projection A0

54.6 mm

Flange transverse width L

115 mm

Source axial dimension A2

22 mm

Insert centre-to-face S

19.0 mm

Insert inner-ring width B

51.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

2.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Overall flange length H

224 mm

Bolt-centre spacing J

184 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Flange transverse width L

130 mm

Source axial dimension A2

25 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Overall flange length H

224 mm

Bolt-centre spacing J

184 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Flange transverse width L

130 mm

Source axial dimension A2

25 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Overall flange length H

224 mm

Bolt-centre spacing J

184 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Flange transverse width L

130 mm

Source axial dimension A2

25 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

43.4 kN

Basic static rating C0r

29.4 kN

Overall flange length H

224 mm

Bolt-centre spacing J

184 mm

Flange thickness A1

18 mm

Housing depth A

43 mm

Overall axial projection A0

58.4 mm

Flange transverse width L

130 mm

Source axial dimension A2

25 mm

Insert centre-to-face S

22.2 mm

Insert inner-ring width B

55.6 mm

Mounting hole diameter N

19 mm

Catalogue mounting bolt

M16

Shared catalogue mass

3.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Overall flange length H

250 mm

Bolt-centre spacing J

202 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Flange transverse width L

140 mm

Source axial dimension A2

29 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Overall flange length H

250 mm

Bolt-centre spacing J

202 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Flange transverse width L

140 mm

Source axial dimension A2

29 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

52.4 kN

Basic static rating C0r

36.2 kN

Overall flange length H

250 mm

Bolt-centre spacing J

202 mm

Flange thickness A1

18 mm

Housing depth A

48 mm

Overall axial projection A0

68.7 mm

Flange transverse width L

140 mm

Source axial dimension A2

29 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

4.2 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

57.2 kN

Basic static rating C0r

40.1 kN

Overall flange length H

258 mm

Bolt-centre spacing J

210 mm

Flange thickness A1

20 mm

Housing depth A

50 mm

Overall axial projection A0

69.7 mm

Flange transverse width L

155 mm

Source axial dimension A2

30 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

5.1 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

57.2 kN

Basic static rating C0r

40.1 kN

Overall flange length H

258 mm

Bolt-centre spacing J

210 mm

Flange thickness A1

20 mm

Housing depth A

50 mm

Overall axial projection A0

69.7 mm

Flange transverse width L

155 mm

Source axial dimension A2

30 mm

Insert centre-to-face S

25.4 mm

Insert inner-ring width B

65.1 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

5.1 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

62.2 kN

Basic static rating C0r

44.1 kN

Overall flange length H

265 mm

Bolt-centre spacing J

216 mm

Flange thickness A1

20 mm

Housing depth A

54 mm

Overall axial projection A0

75.4 mm

Flange transverse width L

160 mm

Source axial dimension A2

31 mm

Insert centre-to-face S

30.2 mm

Insert inner-ring width B

74.6 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

5.7 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

62.2 kN

Basic static rating C0r

44.1 kN

Overall flange length H

265 mm

Bolt-centre spacing J

216 mm

Flange thickness A1

20 mm

Housing depth A

54 mm

Overall axial projection A0

75.4 mm

Flange transverse width L

160 mm

Source axial dimension A2

31 mm

Insert centre-to-face S

30.2 mm

Insert inner-ring width B

74.6 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

5.7 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Overall flange length H

275 mm

Bolt-centre spacing J

225 mm

Flange thickness A1

20 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Flange transverse width L

165 mm

Source axial dimension A2

34 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Overall flange length H

275 mm

Bolt-centre spacing J

225 mm

Flange thickness A1

20 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Flange transverse width L

165 mm

Source axial dimension A2

34 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

67.4 kN

Basic static rating C0r

48.3 kN

Overall flange length H

275 mm

Bolt-centre spacing J

225 mm

Flange thickness A1

20 mm

Housing depth A

56 mm

Overall axial projection A0

78.5 mm

Flange transverse width L

165 mm

Source axial dimension A2

34 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

77.8 mm

Mounting hole diameter N

23 mm

Catalogue mounting bolt

M20

Shared catalogue mass

6.4 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

72.7 kN

Basic static rating C0r

53.0 kN

Overall flange length H

290 mm

Bolt-centre spacing J

233 mm

Flange thickness A1

20 mm

Housing depth A

58 mm

Overall axial projection A0

83.3 mm

Flange transverse width L

180 mm

Source axial dimension A2

34 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

82.6 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

7.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

72.7 kN

Basic static rating C0r

53.0 kN

Overall flange length H

290 mm

Bolt-centre spacing J

233 mm

Flange thickness A1

20 mm

Housing depth A

58 mm

Overall axial projection A0

83.3 mm

Flange transverse width L

180 mm

Source axial dimension A2

34 mm

Insert centre-to-face S

33.3 mm

Insert inner-ring width B

82.6 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

7.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

84.0 kN

Basic static rating C0r

61.9 kN

Overall flange length H

305 mm

Bolt-centre spacing J

248 mm

Flange thickness A1

22 mm

Housing depth A

63 mm

Overall axial projection A0

87.6 mm

Flange transverse width L

190 mm

Source axial dimension A2

36 mm

Insert centre-to-face S

34.1 mm

Insert inner-ring width B

85.7 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

9.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

84.0 kN

Basic static rating C0r

61.9 kN

Overall flange length H

305 mm

Bolt-centre spacing J

248 mm

Flange thickness A1

22 mm

Housing depth A

63 mm

Overall axial projection A0

87.6 mm

Flange transverse width L

190 mm

Source axial dimension A2

36 mm

Insert centre-to-face S

34.1 mm

Insert inner-ring width B

85.7 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

9.8 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

96.1 kN

Basic static rating C0r

71.5 kN

Overall flange length H

320 mm

Bolt-centre spacing J

265 mm

Flange thickness A1

23 mm

Housing depth A

68 mm

Overall axial projection A0

96.3 mm

Flange transverse width L

205 mm

Source axial dimension A2

40 mm

Insert centre-to-face S

39.7 mm

Insert inner-ring width B

96.0 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

12.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Basic dynamic rating Cr

96.1 kN

Basic static rating C0r

71.5 kN

Overall flange length H

320 mm

Bolt-centre spacing J

265 mm

Flange thickness A1

23 mm

Housing depth A

68 mm

Overall axial projection A0

96.3 mm

Flange transverse width L

205 mm

Source axial dimension A2

40 mm

Insert centre-to-face S

39.7 mm

Insert inner-ring width B

96.0 mm

Mounting hole diameter N

25 mm

Catalogue mounting bolt

M22

Shared catalogue mass

12.3 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

J is spacing between the two mounting-hole centres. H is overall flange length, L its shorter transverse width. Neither is the insert outside diameter.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 25. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.