Find · understand · compare

Mounted bearing units: types, dimensions & brand filters

A complete insert-and-housing assembly, rather than a bare bearing.

On this page19 sections

Complete-unit reference

Find a Dodge mounted bearing by shaft size

Search by designation, shaft diameter and mounting form. Compare installation dimensions in their original units.

260verified catalogue references

Selected SC-family set-screw ball-bearing units only—not the complete Dodge catalogue. A missing result does not mean a part does not exist.

260 references. Open a row to inspect its original dimensions and source pages.

All references and their dimensions are available below without JavaScript. Use your browser’s Find command to locate a designation. Interactive filtering and side-by-side comparison require JavaScript.

Read the size and mounting symbols correctly

1 7/16 in = 36.5125 mm, not 35 mm. Inch and metric shaft sizes remain distinct. The shaft filter converts only the entered bore for matching; it does not turn an inch assembly into a metric one.

P2B pillow block: compare base length B, mounting-slot range D, centre height M and overall height J.
F2B flange: compare flange length B, bolt-centre distance D, width M and total depth C.
F4B flange: compare square-flange side B, bolt-centre pitch D and total depth C.
WSTU take-up: check the recorded frame designation and the drawing-specific slot dimensions. An M value with a slash is a pair of limits, not a fraction.

Letter meanings change between housing forms. The comparison tool therefore accepts only the same mounting form. Dimensions stay in the source unit; an M10-style bolt designation is not a length. The remaining lettered values need the matching manufacturer drawing before installation.

P2B-SC-008Two-bolt pillow block · SC1/2 inShaft diameter123830Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Base length B: 5.00 in
Base width C: 1.20 in
Bolt-centre minimum D: 3.25 in
Bolt-centre maximum D: 4.06 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.84 in
Drawing dimension H: 0.47 in
Overall height J: 2.14 in
Drawing dimension L: 0.96 in
Shaft centre height M: 1.06 in
Drawing dimension R: 0.36 in
Drawing dimension S: 0.64 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.38 in
Drawing dimension X: 0.12 in
Assembly mass: 1.1 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-13, B1-14 (PDF pages 24, 25). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

P2B-SC-010Two-bolt pillow block · SC5/8 inShaft diameter123831Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Base length B: 5.00 in
Base width C: 1.20 in
Bolt-centre minimum D: 3.25 in
Bolt-centre maximum D: 4.06 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.84 in
Drawing dimension H: 0.47 in
Overall height J: 2.14 in
Drawing dimension L: 0.96 in
Shaft centre height M: 1.06 in
Drawing dimension R: 0.36 in
Drawing dimension S: 0.64 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.38 in
Drawing dimension X: 0.12 in
Assembly mass: 1.0 lb

P2B-SC-17MTwo-bolt pillow block · SC17 mmShaft diameter053170Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 25.4 mm
Base length B: 127.0 mm
Base width C: 30.5 mm
Bolt-centre minimum D: 82.6 mm
Bolt-centre maximum D: 103.1 mm
Mounting bolt F: M10
Drawing dimension G: 21.3 mm
Drawing dimension H: 11.9 mm
Overall height J: 54.4 mm
Drawing dimension L: 24.4 mm
Shaft centre height M: 27.0 mm
Drawing dimension R: 9.1 mm
Drawing dimension S: 16.3 mm
Drawing dimension U: 57.2 mm
Drawing dimension V: 114.3 mm
Drawing dimension W: 9.7 mm
Drawing dimension X: 3.0 mm
Assembly mass: 0.4 kg

P2B-SCU-008Two-bolt pillow block · SCU1/2 inShaft diameter123753Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Base length B: 5.00 in
Base width C: 1.20 in
Bolt-centre minimum D: 3.25 in
Bolt-centre maximum D: 4.06 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.84 in
Drawing dimension H: 0.59 in
Overall height J: 2.27 in
Drawing dimension L: 0.96 in
Shaft centre height M: 1.19 in
Drawing dimension R: 0.36 in
Drawing dimension S: 0.64 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.38 in
Drawing dimension X: 0.12 in
Assembly mass: 1.2 lb

P2B-SCU-010Two-bolt pillow block · SCU5/8 inShaft diameter123754Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Base length B: 5.00 in
Base width C: 1.20 in
Bolt-centre minimum D: 3.25 in
Bolt-centre maximum D: 4.06 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.84 in
Drawing dimension H: 0.59 in
Overall height J: 2.27 in
Drawing dimension L: 0.96 in
Shaft centre height M: 1.19 in
Drawing dimension R: 0.36 in
Drawing dimension S: 0.64 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.38 in
Drawing dimension X: 0.12 in
Assembly mass: 1.0 lb

P2B-SCU-17MTwo-bolt pillow block · SCU17 mmShaft diameter125850Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 25.4 mm
Base length B: 127.0 mm
Base width C: 30.5 mm
Bolt-centre minimum D: 82.6 mm
Bolt-centre maximum D: 103.1 mm
Mounting bolt F: M10
Drawing dimension G: 21.3 mm
Drawing dimension H: 15.0 mm
Overall height J: 57.7 mm
Drawing dimension L: 24.4 mm
Shaft centre height M: 30.2 mm
Drawing dimension R: 9.1 mm
Drawing dimension S: 16.3 mm
Drawing dimension U: 57.2 mm
Drawing dimension V: 114.3 mm
Drawing dimension W: 9.7 mm
Drawing dimension X: 3.0 mm
Assembly mass: 0.4 kg

P2B-SC-008LTwo-bolt pillow block · SC1/2 inShaft diameter123835Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Base length B: 5.25 in
Base width C: 1.34 in
Bolt-centre minimum D: 3.38 in
Bolt-centre maximum D: 4.19 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.53 in
Overall height J: 2.56 in
Drawing dimension L: 1.12 in
Shaft centre height M: 1.31 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.6 lb

P2B-SC-010LTwo-bolt pillow block · SC5/8 inShaft diameter123836Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Base length B: 5.25 in
Base width C: 1.34 in
Bolt-centre minimum D: 3.38 in
Bolt-centre maximum D: 4.19 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.53 in
Overall height J: 2.56 in
Drawing dimension L: 1.12 in
Shaft centre height M: 1.31 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.5 lb

P2B-SC-012Two-bolt pillow block · SC3/4 inShaft diameter123803Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Base length B: 5.25 in
Base width C: 1.34 in
Bolt-centre minimum D: 3.38 in
Bolt-centre maximum D: 4.19 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.53 in
Overall height J: 2.56 in
Drawing dimension L: 1.12 in
Shaft centre height M: 1.31 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension U: 2.25 in
Drawing dimension V: 4.50 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.4 lb

P2B-SC-20MTwo-bolt pillow block · SC20 mmShaft diameter125851Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 31.2 mm
Base length B: 133.4 mm
Base width C: 34.0 mm
Bolt-centre minimum D: 85.9 mm
Bolt-centre maximum D: 106.4 mm
Mounting bolt F: M10
Drawing dimension G: 21.6 mm
Drawing dimension H: 13.5 mm
Overall height J: 65.0 mm
Drawing dimension L: 28.4 mm
Shaft centre height M: 33.3 mm
Drawing dimension R: 12.7 mm
Drawing dimension S: 18.5 mm
Drawing dimension U: 57.2 mm
Drawing dimension V: 114.3 mm
Drawing dimension W: 12.7 mm
Drawing dimension X: 3.0 mm
Assembly mass: 0.7 kg

P2B-SC-014Two-bolt pillow block · SC7/8 inShaft diameter123804Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Base length B: 5.50 in
Base width C: 1.40 in
Bolt-centre minimum D: 3.69 in
Bolt-centre maximum D: 4.50 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.58 in
Overall height J: 2.77 in
Drawing dimension L: 1.32 in
Shaft centre height M: 1.44 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension U: 2.50 in
Drawing dimension V: 5.00 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.8 lb

P2B-SC-015Two-bolt pillow block · SC15/16 inShaft diameter123805Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Base length B: 5.50 in
Base width C: 1.40 in
Bolt-centre minimum D: 3.69 in
Bolt-centre maximum D: 4.50 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.58 in
Overall height J: 2.77 in
Drawing dimension L: 1.32 in
Shaft centre height M: 1.44 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension U: 2.50 in
Drawing dimension V: 5.00 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.7 lb

P2B-SC-100Two-bolt pillow block · SC1 inShaft diameter123806Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Base length B: 5.50 in
Base width C: 1.40 in
Bolt-centre minimum D: 3.69 in
Bolt-centre maximum D: 4.50 in
Mounting bolt F: 3/8 in
Drawing dimension G: 0.85 in
Drawing dimension H: 0.58 in
Overall height J: 2.77 in
Drawing dimension L: 1.32 in
Shaft centre height M: 1.44 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension U: 2.50 in
Drawing dimension V: 5.00 in
Drawing dimension W: 0.50 in
Drawing dimension X: 0.12 in
Assembly mass: 1.6 lb

P2B-SC-25MTwo-bolt pillow block · SC25 mmShaft diameter125852Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 34.0 mm
Base length B: 139.7 mm
Base width C: 35.6 mm
Bolt-centre minimum D: 93.7 mm
Bolt-centre maximum D: 114.3 mm
Mounting bolt F: M10
Drawing dimension G: 21.6 mm
Drawing dimension H: 14.7 mm
Overall height J: 70.4 mm
Drawing dimension L: 33.5 mm
Shaft centre height M: 36.5 mm
Drawing dimension R: 14.2 mm
Drawing dimension S: 19.8 mm
Drawing dimension U: 63.5 mm
Drawing dimension V: 127.0 mm
Drawing dimension W: 12.7 mm
Drawing dimension X: 3.0 mm
Assembly mass: 0.7 kg

P2B-SC-101Two-bolt pillow block · SC1-1/16 inShaft diameter123807Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.68 in
Overall height J: 3.25 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.63 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.8 lb

P2B-SC-102Two-bolt pillow block · SC1-1/8 inShaft diameter123808Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.68 in
Overall height J: 3.25 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.63 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.7 lb

P2B-SC-103Two-bolt pillow block · SC1-3/16 inShaft diameter123809Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.68 in
Overall height J: 3.25 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.63 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.6 lb

P2B-SC-104STwo-bolt pillow block · SC1-1/4 inShaft diameter123170Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.68 in
Overall height J: 3.25 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.63 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.5 lb

P2B-SC-30MTwo-bolt pillow block · SC30 mmShaft diameter125853Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Base length B: 158.8 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 108.0 mm
Bolt-centre maximum D: 127.0 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 17.3 mm
Overall height J: 82.6 mm
Drawing dimension L: 39.9 mm
Shaft centre height M: 41.3 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension U: 73.2 mm
Drawing dimension V: 146.3 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 1.1 kg

P2B-SCU-101Two-bolt pillow block · SCU1-1/16 inShaft diameter123877Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.75 in
Overall height J: 3.31 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.69 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.9 lb

P2B-SCU-102Two-bolt pillow block · SCU1-1/8 inShaft diameter123878Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.75 in
Overall height J: 3.31 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.69 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.8 lb

P2B-SCU-103Two-bolt pillow block · SCU1-3/16 inShaft diameter123879Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.75 in
Overall height J: 3.31 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.69 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.7 lb

P2B-SCU-104STwo-bolt pillow block · SCU1-1/4 inShaft diameter123894Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.75 in
Overall height J: 3.31 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.69 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 2.6 lb

P2B-SCU-30MTwo-bolt pillow block · SCU30 mmShaft diameter125854Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Base length B: 158.8 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 108.0 mm
Bolt-centre maximum D: 127.0 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 19.1 mm
Overall height J: 84.1 mm
Drawing dimension L: 39.9 mm
Shaft centre height M: 42.9 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension U: 73.2 mm
Drawing dimension V: 146.3 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 1.1 kg

P2B-SC-105Two-bolt pillow block · SC1-5/16 inShaft diameter123811Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Base length B: 6.50 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.68 in
Bolt-centre maximum D: 5.44 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.71 in
Overall height J: 3.75 in
Drawing dimension L: 1.84 in
Shaft centre height M: 1.88 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension U: 2.91 in
Drawing dimension V: 5.82 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 4.4 lb

P2B-SC-106Two-bolt pillow block · SC1-3/8 inShaft diameter123812Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Base length B: 6.50 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.68 in
Bolt-centre maximum D: 5.44 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.71 in
Overall height J: 3.75 in
Drawing dimension L: 1.84 in
Shaft centre height M: 1.88 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension U: 2.91 in
Drawing dimension V: 5.82 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 4.3 lb

P2B-SC-107Two-bolt pillow block · SC1-7/16 inShaft diameter123813Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Base length B: 6.50 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.68 in
Bolt-centre maximum D: 5.44 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.71 in
Overall height J: 3.75 in
Drawing dimension L: 1.84 in
Shaft centre height M: 1.88 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension U: 2.91 in
Drawing dimension V: 5.82 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 4.2 lb

P2B-SC-35MTwo-bolt pillow block · SC35 mmShaft diameter125855Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Base length B: 165.1 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 118.9 mm
Bolt-centre maximum D: 138.2 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 18.0 mm
Overall height J: 95.3 mm
Drawing dimension L: 46.7 mm
Shaft centre height M: 47.6 mm
Drawing dimension R: 17.0 mm
Drawing dimension S: 26.4 mm
Drawing dimension U: 73.9 mm
Drawing dimension V: 147.8 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 1.5 kg

P2B-SC-108Two-bolt pillow block · SC1-1/2 inShaft diameter123814Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.25 in
Base width C: 1.93 in
Bolt-centre minimum D: 5.18 in
Bolt-centre maximum D: 5.88 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.91 in
Drawing dimension H: 0.93 in
Overall height J: 4.19 in
Drawing dimension L: 2.05 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.26 in
Drawing dimension V: 6.52 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 5.4 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-15, B1-16 (PDF pages 26, 27). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

P2B-SC-110Two-bolt pillow block · SC1-5/8 inShaft diameter123815Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.25 in
Base width C: 1.93 in
Bolt-centre minimum D: 5.18 in
Bolt-centre maximum D: 5.88 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.91 in
Drawing dimension H: 0.93 in
Overall height J: 4.19 in
Drawing dimension L: 2.05 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.26 in
Drawing dimension V: 6.52 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 5.3 lb

P2B-SC-40MTwo-bolt pillow block · SC40 mmShaft diameter056855Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 184.2 mm
Base width C: 49.0 mm
Bolt-centre minimum D: 131.6 mm
Bolt-centre maximum D: 149.4 mm
Mounting bolt F: M12
Drawing dimension G: 23.1 mm
Drawing dimension H: 23.6 mm
Overall height J: 106.4 mm
Drawing dimension L: 52.1 mm
Shaft centre height M: 54.0 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 82.8 mm
Drawing dimension V: 165.6 mm
Drawing dimension W: 17.5 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.2 kg

P2B-SC-111Two-bolt pillow block · SC1-11/16 inShaft diameter123816Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.44 in
Base width C: 2.00 in
Bolt-centre minimum D: 5.50 in
Bolt-centre maximum D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.90 in
Drawing dimension H: 0.75 in
Overall height J: 4.28 in
Drawing dimension L: 2.22 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.38 in
Drawing dimension V: 6.76 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 6.4 lb

P2B-SC-112Two-bolt pillow block · SC1-3/4 inShaft diameter123817Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.44 in
Base width C: 2.00 in
Bolt-centre minimum D: 5.50 in
Bolt-centre maximum D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.90 in
Drawing dimension H: 0.75 in
Overall height J: 4.28 in
Drawing dimension L: 2.22 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.38 in
Drawing dimension V: 6.76 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 6.2 lb

P2B-SC-45MTwo-bolt pillow block · SC45 mmShaft diameter125857Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 189.0 mm
Base width C: 50.8 mm
Bolt-centre minimum D: 139.7 mm
Bolt-centre maximum D: 157.2 mm
Mounting bolt F: M12
Drawing dimension G: 22.9 mm
Drawing dimension H: 19.1 mm
Overall height J: 108.7 mm
Drawing dimension L: 56.4 mm
Shaft centre height M: 54.0 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 85.9 mm
Drawing dimension V: 171.7 mm
Drawing dimension W: 17.5 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.2 kg

P2B-SC-115Two-bolt pillow block · SC1-15/16 inShaft diameter123818Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 8.12 in
Base width C: 2.25 in
Bolt-centre minimum D: 6.00 in
Bolt-centre maximum D: 6.68 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.02 in
Drawing dimension H: 0.75 in
Overall height J: 4.53 in
Drawing dimension L: 2.43 in
Shaft centre height M: 2.25 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.69 in
Drawing dimension V: 7.38 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 7.2 lb

P2B-SC-200Two-bolt pillow block · SC2 inShaft diameter123819Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 8.12 in
Base width C: 2.25 in
Bolt-centre minimum D: 6.00 in
Bolt-centre maximum D: 6.68 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.02 in
Drawing dimension H: 0.75 in
Overall height J: 4.53 in
Drawing dimension L: 2.43 in
Shaft centre height M: 2.25 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.69 in
Drawing dimension V: 7.38 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 7.0 lb

P2B-SC-50MTwo-bolt pillow block · SC50 mmShaft diameter125858Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 206.2 mm
Base width C: 57.2 mm
Bolt-centre minimum D: 152.4 mm
Bolt-centre maximum D: 169.7 mm
Mounting bolt F: M16
Drawing dimension G: 25.9 mm
Drawing dimension H: 19.1 mm
Overall height J: 115.1 mm
Drawing dimension L: 61.7 mm
Shaft centre height M: 57.2 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 93.7 mm
Drawing dimension V: 187.5 mm
Drawing dimension W: 20.6 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.6 kg

P2B-SCM-200Two-bolt pillow block · SCM2 inShaft diameter126815Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Base length B: 8.88 in
Base width C: 2.30 in
Bolt-centre minimum D: 6.38 in
Bolt-centre maximum D: 7.44 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 4.96 in
Drawing dimension L: 2.71 in
Shaft centre height M: 2.50 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension U: 3.94 in
Drawing dimension V: 7.88 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 9.0 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-15, B1-16, B1-21, B1-22 (PDF pages 26, 27, 32, 33). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

P2B-SC-203Two-bolt pillow block · SC2-3/16 inShaft diameter123820Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Base length B: 8.88 in
Base width C: 2.30 in
Bolt-centre minimum D: 6.38 in
Bolt-centre maximum D: 7.44 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 4.96 in
Drawing dimension L: 2.71 in
Shaft centre height M: 2.50 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension U: 3.94 in
Drawing dimension V: 7.88 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 8.9 lb

P2B-SC-204Two-bolt pillow block · SC2-1/4 inShaft diameter123821Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Base length B: 8.88 in
Base width C: 2.30 in
Bolt-centre minimum D: 6.38 in
Bolt-centre maximum D: 7.44 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 4.96 in
Drawing dimension L: 2.71 in
Shaft centre height M: 2.50 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension U: 3.94 in
Drawing dimension V: 7.88 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 8.8 lb

P2B-SC-55MTwo-bolt pillow block · SC55 mmShaft diameter125859Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Base length B: 225.6 mm
Base width C: 58.4 mm
Bolt-centre minimum D: 162.1 mm
Bolt-centre maximum D: 189.0 mm
Mounting bolt F: M16
Drawing dimension G: 30.7 mm
Drawing dimension H: 22.4 mm
Overall height J: 126.0 mm
Drawing dimension L: 68.8 mm
Shaft centre height M: 63.5 mm
Drawing dimension R: 22.1 mm
Drawing dimension S: 34.3 mm
Drawing dimension U: 100.1 mm
Drawing dimension V: 200.2 mm
Drawing dimension W: 20.6 mm
Drawing dimension X: 3.0 mm
Assembly mass: 3.3 kg

P2B-SCM-204Two-bolt pillow block · SCM2-1/4 inShaft diameter126817Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Base length B: 9.50 in
Base width C: 2.37 in
Bolt-centre minimum D: 6.88 in
Bolt-centre maximum D: 7.94 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 5.40 in
Drawing dimension L: 2.97 in
Shaft centre height M: 2.75 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension U: 4.25 in
Drawing dimension V: 8.50 in
Drawing dimension W: 0.88 in
Drawing dimension X: 0.12 in
Assembly mass: 10.8 lb

P2B-SC-207Two-bolt pillow block · SC2-7/16 inShaft diameter123822Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Base length B: 9.50 in
Base width C: 2.37 in
Bolt-centre minimum D: 6.88 in
Bolt-centre maximum D: 7.94 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 5.40 in
Drawing dimension L: 2.97 in
Shaft centre height M: 2.75 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension U: 4.25 in
Drawing dimension V: 8.50 in
Drawing dimension W: 0.88 in
Drawing dimension X: 0.12 in
Assembly mass: 10.2 lb

P2B-SC-60MTwo-bolt pillow block · SC60 mmShaft diameter125860Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Base length B: 241.3 mm
Base width C: 60.2 mm
Bolt-centre minimum D: 174.8 mm
Bolt-centre maximum D: 201.7 mm
Mounting bolt F: M16
Drawing dimension G: 30.7 mm
Drawing dimension H: 22.4 mm
Overall height J: 137.2 mm
Drawing dimension L: 75.4 mm
Shaft centre height M: 69.9 mm
Drawing dimension R: 22.9 mm
Drawing dimension S: 35.8 mm
Drawing dimension U: 108.0 mm
Drawing dimension V: 215.9 mm
Drawing dimension W: 22.4 mm
Drawing dimension X: 3.0 mm
Assembly mass: 4.2 kg

P2B-SCM-208Two-bolt pillow block · SCM2-1/2 inShaft diameter126819Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Base length B: 10.75 in
Base width C: 2.69 in
Bolt-centre minimum D: 7.50 in
Bolt-centre maximum D: 8.50 in
Mounting bolt F: 3/4 in
Drawing dimension G: 1.32 in
Drawing dimension H: 0.94 in
Overall height J: 6.09 in
Drawing dimension L: 3.31 in
Shaft centre height M: 3.00 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension U: 4.88 in
Drawing dimension V: 9.76 in
Drawing dimension W: 0.94 in
Drawing dimension X: 0.12 in
Assembly mass: 15.5 lb

P2B-SC-211Two-bolt pillow block · SC2-11/16 inShaft diameter123839Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Base length B: 10.75 in
Base width C: 2.69 in
Bolt-centre minimum D: 7.50 in
Bolt-centre maximum D: 8.50 in
Mounting bolt F: 3/4 in
Drawing dimension G: 1.32 in
Drawing dimension H: 0.94 in
Overall height J: 6.09 in
Drawing dimension L: 3.31 in
Shaft centre height M: 3.00 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension U: 4.88 in
Drawing dimension V: 9.76 in
Drawing dimension W: 0.94 in
Drawing dimension X: 0.12 in
Assembly mass: 15.0 lb

P2B-SC-70MTwo-bolt pillow block · SC70 mmShaft diameter125861Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Base length B: 273.1 mm
Base width C: 68.3 mm
Bolt-centre minimum D: 190.5 mm
Bolt-centre maximum D: 215.9 mm
Mounting bolt F: M18
Drawing dimension G: 33.5 mm
Drawing dimension H: 23.9 mm
Overall height J: 154.7 mm
Drawing dimension L: 84.1 mm
Shaft centre height M: 76.2 mm
Drawing dimension R: 26.9 mm
Drawing dimension S: 37.6 mm
Drawing dimension U: 124.0 mm
Drawing dimension V: 247.9 mm
Drawing dimension W: 23.9 mm
Drawing dimension X: 3.0 mm
Assembly mass: 6.9 kg

P2B-SC-215Two-bolt pillow block · SC2-15/16 inShaft diameter123823Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Base length B: 11.75 in
Base width C: 2.88 in
Bolt-centre minimum D: 8.50 in
Bolt-centre maximum D: 9.50 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.44 in
Drawing dimension H: 1.00 in
Overall height J: 6.75 in
Drawing dimension L: 3.62 in
Shaft centre height M: 3.50 in
Drawing dimension R: 0.86 in
Drawing dimension S: 1.47 in
Drawing dimension U: 5.48 in
Drawing dimension V: 10.96 in
Drawing dimension W: 1.04 in
Drawing dimension X: 0.12 in
Assembly mass: 20.5 lb

P2B-SC-75MTwo-bolt pillow block · SC75 mmShaft diameter125862Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Base length B: 298.5 mm
Base width C: 73.2 mm
Bolt-centre minimum D: 215.9 mm
Bolt-centre maximum D: 241.3 mm
Mounting bolt F: M22
Drawing dimension G: 36.6 mm
Drawing dimension H: 25.4 mm
Overall height J: 171.5 mm
Drawing dimension L: 91.9 mm
Shaft centre height M: 88.9 mm
Drawing dimension R: 21.8 mm
Drawing dimension S: 37.3 mm
Drawing dimension U: 139.2 mm
Drawing dimension V: 278.4 mm
Drawing dimension W: 26.4 mm
Drawing dimension X: 3.0 mm
Assembly mass: 7.9 kg

P2B-SCU-215Two-bolt pillow block · SCU2-15/16 inShaft diameter123728Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Base length B: 11.75 in
Base width C: 2.88 in
Bolt-centre minimum D: 8.50 in
Bolt-centre maximum D: 9.50 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.44 in
Drawing dimension H: 1.00 in
Overall height J: 6.50 in
Drawing dimension L: 3.62 in
Shaft centre height M: 3.25 in
Drawing dimension R: 0.86 in
Drawing dimension S: 1.47 in
Drawing dimension U: 5.48 in
Drawing dimension V: 10.96 in
Drawing dimension W: 1.04 in
Drawing dimension X: 0.12 in
Assembly mass: 20.7 lb

P2B-SCU-75MTwo-bolt pillow block · SCU75 mmShaft diameter052792Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Base length B: 298.5 mm
Base width C: 73.2 mm
Bolt-centre minimum D: 215.9 mm
Bolt-centre maximum D: 241.3 mm
Mounting bolt F: M22
Drawing dimension G: 36.6 mm
Drawing dimension H: 25.4 mm
Overall height J: 165.1 mm
Drawing dimension L: 91.9 mm
Shaft centre height M: 82.6 mm
Drawing dimension R: 21.8 mm
Drawing dimension S: 37.3 mm
Drawing dimension U: 139.2 mm
Drawing dimension V: 278.4 mm
Drawing dimension W: 26.4 mm
Drawing dimension X: 3.0 mm
Assembly mass: 8.0 kg

P2B-SC-90MTwo-bolt pillow block · SC90 mmShaft diameter052794Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 65.0 mm
Base length B: 355.6 mm
Base width C: 85.9 mm
Bolt-centre minimum D: 262.1 mm
Bolt-centre maximum D: 295.1 mm
Mounting bolt F: M22
Drawing dimension G: 40.4 mm
Drawing dimension H: 33.3 mm
Overall height J: 203.2 mm
Drawing dimension L: 110.5 mm
Shaft centre height M: 101.6 mm
Drawing dimension R: 24.4 mm
Drawing dimension S: 40.6 mm
Drawing dimension U: 167.6 mm
Drawing dimension V: 335.3 mm
Drawing dimension W: 30.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 13.6 kg

P2B-SCM-100Two-bolt pillow block · SCM1 inShaft diameter126147Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.68 in
Overall height J: 3.25 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.69 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 3.0 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-21, B1-22 (PDF pages 32, 33). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

P2B-SCM-25MTwo-bolt pillow block · SCM25 mmShaft diameter125925Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Base length B: 158.8 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 108.0 mm
Bolt-centre maximum D: 127.0 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 17.3 mm
Overall height J: 82.6 mm
Drawing dimension L: 39.9 mm
Shaft centre height M: 42.9 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension U: 73.2 mm
Drawing dimension V: 146.3 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 1.3 kg

P2B-SCMU-100Two-bolt pillow block · SCMU1 inShaft diameter064249Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Base length B: 6.25 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.25 in
Bolt-centre maximum D: 5.00 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.81 in
Overall height J: 3.37 in
Drawing dimension L: 1.57 in
Shaft centre height M: 1.75 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension U: 2.88 in
Drawing dimension V: 5.76 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 3.1 lb

P2B-SCMU-25MTwo-bolt pillow block · SCMU25 mmShaft diameterOrder-only referenceNumeric part number not statedDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Base length B: 158.8 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 108.0 mm
Bolt-centre maximum D: 127.0 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 20.6 mm
Overall height J: 85.6 mm
Drawing dimension L: 39.9 mm
Shaft centre height M: 44.5 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension U: 73.2 mm
Drawing dimension V: 146.3 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 1.4 kg

P2B-SCM-103Two-bolt pillow block · SCM1-3/16 inShaft diameter126148Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Base length B: 6.50 in
Base width C: 1.75 in
Bolt-centre minimum D: 4.68 in
Bolt-centre maximum D: 5.44 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.94 in
Drawing dimension H: 0.71 in
Overall height J: 3.75 in
Drawing dimension L: 1.84 in
Shaft centre height M: 1.88 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension U: 2.91 in
Drawing dimension V: 5.82 in
Drawing dimension W: 0.56 in
Drawing dimension X: 0.12 in
Assembly mass: 4.6 lb

P2B-SCM-30MTwo-bolt pillow block · SCM30 mmShaft diameter125926Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Base length B: 165.1 mm
Base width C: 44.5 mm
Bolt-centre minimum D: 118.9 mm
Bolt-centre maximum D: 138.2 mm
Mounting bolt F: M12
Drawing dimension G: 23.9 mm
Drawing dimension H: 18.0 mm
Overall height J: 95.3 mm
Drawing dimension L: 46.7 mm
Shaft centre height M: 47.6 mm
Drawing dimension R: 17.0 mm
Drawing dimension S: 26.4 mm
Drawing dimension U: 73.9 mm
Drawing dimension V: 147.8 mm
Drawing dimension W: 14.2 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.0 kg

P2B-SCM-107Two-bolt pillow block · SCM1-7/16 inShaft diameter126810Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.25 in
Base width C: 1.93 in
Bolt-centre minimum D: 5.18 in
Bolt-centre maximum D: 5.88 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.91 in
Drawing dimension H: 0.93 in
Overall height J: 4.19 in
Drawing dimension L: 2.05 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.26 in
Drawing dimension V: 6.52 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 5.4 lb

P2B-SCM-35MTwo-bolt pillow block · SCM35 mmShaft diameter125927Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 184.2 mm
Base width C: 49.0 mm
Bolt-centre minimum D: 131.6 mm
Bolt-centre maximum D: 149.4 mm
Mounting bolt F: M12
Drawing dimension G: 23.1 mm
Drawing dimension H: 23.6 mm
Overall height J: 106.4 mm
Drawing dimension L: 52.1 mm
Shaft centre height M: 54.0 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 82.8 mm
Drawing dimension V: 165.6 mm
Drawing dimension W: 17.5 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.3 kg

P2B-SCM-108Two-bolt pillow block · SCM1-1/2 inShaft diameter126811Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 7.44 in
Base width C: 2.00 in
Bolt-centre minimum D: 5.50 in
Bolt-centre maximum D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension G: 0.90 in
Drawing dimension H: 0.75 in
Overall height J: 4.28 in
Drawing dimension L: 2.22 in
Shaft centre height M: 2.13 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.38 in
Drawing dimension V: 6.76 in
Drawing dimension W: 0.69 in
Drawing dimension X: 0.12 in
Assembly mass: 6.4 lb

P2B-SCM-40MTwo-bolt pillow block · SCM40 mmShaft diameter125928Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 189.0 mm
Base width C: 50.8 mm
Bolt-centre minimum D: 139.7 mm
Bolt-centre maximum D: 157.2 mm
Mounting bolt F: M12
Drawing dimension G: 22.9 mm
Drawing dimension H: 19.1 mm
Overall height J: 108.7 mm
Drawing dimension L: 56.4 mm
Shaft centre height M: 54.0 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 85.9 mm
Drawing dimension V: 171.7 mm
Drawing dimension W: 17.5 mm
Drawing dimension X: 3.0 mm
Assembly mass: 2.7 kg

P2B-SCM-111Two-bolt pillow block · SCM1-11/16 inShaft diameter126812Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 8.12 in
Base width C: 2.25 in
Bolt-centre minimum D: 6.00 in
Bolt-centre maximum D: 6.68 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.02 in
Drawing dimension H: 0.75 in
Overall height J: 4.53 in
Drawing dimension L: 2.43 in
Shaft centre height M: 2.25 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.69 in
Drawing dimension V: 7.38 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 7.4 lb

P2B-SCM-112Two-bolt pillow block · SCM1-3/4 inShaft diameter126813Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Base length B: 8.12 in
Base width C: 2.25 in
Bolt-centre minimum D: 6.00 in
Bolt-centre maximum D: 6.68 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.02 in
Drawing dimension H: 0.75 in
Overall height J: 4.53 in
Drawing dimension L: 2.43 in
Shaft centre height M: 2.25 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension U: 3.69 in
Drawing dimension V: 7.38 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 7.3 lb

P2B-SCM-45MTwo-bolt pillow block · SCM45 mmShaft diameter125929Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Base length B: 206.2 mm
Base width C: 57.2 mm
Bolt-centre minimum D: 152.4 mm
Bolt-centre maximum D: 169.7 mm
Mounting bolt F: M16
Drawing dimension G: 25.9 mm
Drawing dimension H: 19.1 mm
Overall height J: 115.1 mm
Drawing dimension L: 61.7 mm
Shaft centre height M: 57.2 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension U: 93.7 mm
Drawing dimension V: 187.5 mm
Drawing dimension W: 20.6 mm
Drawing dimension X: 3.0 mm
Assembly mass: 3.2 kg

P2B-SCM-115Two-bolt pillow block · SCM1-15/16 inShaft diameter126814Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Base length B: 8.88 in
Base width C: 2.30 in
Bolt-centre minimum D: 6.38 in
Bolt-centre maximum D: 7.44 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 4.96 in
Drawing dimension L: 2.71 in
Shaft centre height M: 2.50 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension U: 3.94 in
Drawing dimension V: 7.88 in
Drawing dimension W: 0.81 in
Drawing dimension X: 0.12 in
Assembly mass: 9.2 lb

P2B-SCM-50MTwo-bolt pillow block · SCM50 mmShaft diameter125930Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Base length B: 225.6 mm
Base width C: 58.4 mm
Bolt-centre minimum D: 162.1 mm
Bolt-centre maximum D: 189.0 mm
Mounting bolt F: M16
Drawing dimension G: 30.7 mm
Drawing dimension H: 22.4 mm
Overall height J: 126.0 mm
Drawing dimension L: 68.8 mm
Shaft centre height M: 63.5 mm
Drawing dimension R: 22.1 mm
Drawing dimension S: 34.3 mm
Drawing dimension U: 100.1 mm
Drawing dimension V: 200.2 mm
Drawing dimension W: 20.6 mm
Drawing dimension X: 3.0 mm
Assembly mass: 3.9 kg

P2B-SCM-203Two-bolt pillow block · SCM2-3/16 inShaft diameter126816Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Base length B: 9.50 in
Base width C: 2.37 in
Bolt-centre minimum D: 6.88 in
Bolt-centre maximum D: 7.94 in
Mounting bolt F: 5/8 in
Drawing dimension G: 1.21 in
Drawing dimension H: 0.88 in
Overall height J: 5.40 in
Drawing dimension L: 2.97 in
Shaft centre height M: 2.75 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension U: 4.25 in
Drawing dimension V: 8.50 in
Drawing dimension W: 0.88 in
Drawing dimension X: 0.12 in
Assembly mass: 11.0 lb

P2B-SCM-55MTwo-bolt pillow block · SCM55 mmShaft diameter125931Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Base length B: 241.3 mm
Base width C: 60.2 mm
Bolt-centre minimum D: 174.8 mm
Bolt-centre maximum D: 201.7 mm
Mounting bolt F: M16
Drawing dimension G: 30.7 mm
Drawing dimension H: 22.4 mm
Overall height J: 137.2 mm
Drawing dimension L: 75.4 mm
Shaft centre height M: 69.9 mm
Drawing dimension R: 22.9 mm
Drawing dimension S: 35.8 mm
Drawing dimension U: 108.0 mm
Drawing dimension V: 215.9 mm
Drawing dimension W: 22.4 mm
Drawing dimension X: 3.0 mm
Assembly mass: 4.7 kg

P2B-SCM-207Two-bolt pillow block · SCM2-7/16 inShaft diameter126818Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Base length B: 10.75 in
Base width C: 2.69 in
Bolt-centre minimum D: 7.50 in
Bolt-centre maximum D: 8.50 in
Mounting bolt F: 3/4 in
Drawing dimension G: 1.32 in
Drawing dimension H: 0.94 in
Overall height J: 6.09 in
Drawing dimension L: 3.31 in
Shaft centre height M: 3.00 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension U: 4.88 in
Drawing dimension V: 9.76 in
Drawing dimension W: 0.94 in
Drawing dimension X: 0.12 in
Assembly mass: 15.7 lb

P2B-SCM-65MTwo-bolt pillow block · SCM65 mmShaft diameter125932Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Base length B: 273.1 mm
Base width C: 68.3 mm
Bolt-centre minimum D: 190.5 mm
Bolt-centre maximum D: 215.9 mm
Mounting bolt F: M18
Drawing dimension G: 33.5 mm
Drawing dimension H: 23.9 mm
Overall height J: 154.7 mm
Drawing dimension L: 84.1 mm
Shaft centre height M: 76.2 mm
Drawing dimension R: 26.9 mm
Drawing dimension S: 37.6 mm
Drawing dimension U: 124.0 mm
Drawing dimension V: 247.9 mm
Drawing dimension W: 23.9 mm
Drawing dimension X: 3.0 mm
Assembly mass: 6.7 kg

P2B-SCM-211Two-bolt pillow block · SCM2-11/16 inShaft diameter126820Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Base length B: 11.75 in
Base width C: 2.88 in
Bolt-centre minimum D: 8.50 in
Bolt-centre maximum D: 9.50 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.44 in
Drawing dimension H: 1.00 in
Overall height J: 6.75 in
Drawing dimension L: 3.62 in
Shaft centre height M: 3.50 in
Drawing dimension R: 0.86 in
Drawing dimension S: 1.47 in
Drawing dimension U: 5.48 in
Drawing dimension V: 10.96 in
Drawing dimension W: 1.04 in
Drawing dimension X: 0.12 in
Assembly mass: 21.0 lb

P2B-SCM-70MTwo-bolt pillow block · SCM70 mmShaft diameter125933Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Base length B: 298.5 mm
Base width C: 73.2 mm
Bolt-centre minimum D: 215.9 mm
Bolt-centre maximum D: 241.3 mm
Mounting bolt F: M22
Drawing dimension G: 36.6 mm
Drawing dimension H: 25.4 mm
Overall height J: 171.5 mm
Drawing dimension L: 91.9 mm
Shaft centre height M: 88.9 mm
Drawing dimension R: 21.8 mm
Drawing dimension S: 37.3 mm
Drawing dimension U: 139.2 mm
Drawing dimension V: 278.4 mm
Drawing dimension W: 26.4 mm
Drawing dimension X: 3.0 mm
Assembly mass: 9.0 kg

P2B-SCM-215Two-bolt pillow block · SCM2-15/16 inShaft diameter126821Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Base length B: 11.75 in
Base width C: 3.00 in
Bolt-centre minimum D: 8.50 in
Bolt-centre maximum D: 9.50 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.44 in
Drawing dimension H: 1.25 in
Overall height J: 6.97 in
Drawing dimension L: 3.83 in
Shaft centre height M: 3.50 in
Drawing dimension R: 0.88 in
Drawing dimension S: 1.50 in
Drawing dimension U: 5.50 in
Drawing dimension V: 11.00 in
Drawing dimension W: 1.09 in
Drawing dimension X: 0.12 in
Assembly mass: 21.3 lb

P2B-SCM-300Two-bolt pillow block · SCM3 inShaft diameter126822Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Base length B: 11.75 in
Base width C: 3.00 in
Bolt-centre minimum D: 8.50 in
Bolt-centre maximum D: 9.50 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.44 in
Drawing dimension H: 1.25 in
Overall height J: 6.97 in
Drawing dimension L: 3.83 in
Shaft centre height M: 3.50 in
Drawing dimension R: 0.88 in
Drawing dimension S: 1.50 in
Drawing dimension U: 5.50 in
Drawing dimension V: 11.00 in
Drawing dimension W: 1.09 in
Drawing dimension X: 0.12 in
Assembly mass: 21.1 lb

P2B-SCM-75MTwo-bolt pillow block · SCM75 mmShaft diameter125934Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 60.5 mm
Base length B: 298.5 mm
Base width C: 76.2 mm
Bolt-centre minimum D: 215.9 mm
Bolt-centre maximum D: 241.3 mm
Mounting bolt F: M22
Drawing dimension G: 36.6 mm
Drawing dimension H: 31.8 mm
Overall height J: 177.0 mm
Drawing dimension L: 97.3 mm
Shaft centre height M: 88.9 mm
Drawing dimension R: 22.4 mm
Drawing dimension S: 38.1 mm
Drawing dimension U: 139.7 mm
Drawing dimension V: 279.4 mm
Drawing dimension W: 27.7 mm
Drawing dimension X: 3.0 mm
Assembly mass: 9.0 kg

P2B-SCM-307Two-bolt pillow block · SCM3-7/16 inShaft diameter126823Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.56 in
Base length B: 14.00 in
Base width C: 3.38 in
Bolt-centre minimum D: 10.32 in
Bolt-centre maximum D: 11.62 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.59 in
Drawing dimension H: 1.31 in
Overall height J: 8.00 in
Drawing dimension L: 4.35 in
Shaft centre height M: 4.00 in
Drawing dimension R: 0.96 in
Drawing dimension S: 1.60 in
Drawing dimension U: 6.60 in
Drawing dimension V: 13.20 in
Drawing dimension W: 1.19 in
Drawing dimension X: 0.12 in
Assembly mass: 31.8 lb

P2B-SCM-308Two-bolt pillow block · SCM3-1/2 inShaft diameter126824Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.56 in
Base length B: 14.00 in
Base width C: 3.38 in
Bolt-centre minimum D: 10.32 in
Bolt-centre maximum D: 11.62 in
Mounting bolt F: 7/8 in
Drawing dimension G: 1.59 in
Drawing dimension H: 1.31 in
Overall height J: 8.00 in
Drawing dimension L: 4.35 in
Shaft centre height M: 4.00 in
Drawing dimension R: 0.96 in
Drawing dimension S: 1.60 in
Drawing dimension U: 6.60 in
Drawing dimension V: 13.20 in
Drawing dimension W: 1.19 in
Drawing dimension X: 0.12 in
Assembly mass: 31.3 lb

F2B-SC-008Two-bolt flange · SC1/2 inShaft diameter124198Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Flange length B: 3.88 in
Overall depth C: 1.17 in
Bolt-centre distance D: 3.00 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.38 in
Drawing dimension J: 0.32 in
Drawing dimension L: 0.96 in
Flange width M: 2.13 in
Drawing dimension N: 1.13 in
Assembly mass: 0.8 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-27, B1-28 (PDF pages 38, 39). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F2B-SC-010Two-bolt flange · SC5/8 inShaft diameter124199Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Flange length B: 3.88 in
Overall depth C: 1.17 in
Bolt-centre distance D: 3.00 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.38 in
Drawing dimension J: 0.32 in
Drawing dimension L: 0.96 in
Flange width M: 2.13 in
Drawing dimension N: 1.13 in
Assembly mass: 0.7 lb

F2B-SC-17MTwo-bolt flange · SC17 mmShaft diameter125875Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 25.4 mm
Flange length B: 98.6 mm
Overall depth C: 29.7 mm
Bolt-centre distance D: 76.2 mm
Mounting bolt F: M10
Drawing dimension H: 9.7 mm
Drawing dimension J: 8.1 mm
Drawing dimension L: 24.4 mm
Flange width M: 54.1 mm
Drawing dimension N: 28.7 mm
Assembly mass: 0.3 kg

F2B-SC-008LTwo-bolt flange · SC1/2 inShaft diameter124166Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange length B: 4.41 in
Overall depth C: 1.34 in
Bolt-centre distance D: 3.53 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Flange width M: 2.38 in
Drawing dimension N: 1.50 in
Assembly mass: 1.6 lb

F2B-SC-010LTwo-bolt flange · SC5/8 inShaft diameter124167Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange length B: 4.41 in
Overall depth C: 1.34 in
Bolt-centre distance D: 3.53 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Flange width M: 2.38 in
Drawing dimension N: 1.50 in
Assembly mass: 1.5 lb

F2B-SC-012Two-bolt flange · SC3/4 inShaft diameter124170Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange length B: 4.41 in
Overall depth C: 1.34 in
Bolt-centre distance D: 3.53 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Flange width M: 2.38 in
Drawing dimension N: 1.50 in
Assembly mass: 1.4 lb

F2B-SC-20MTwo-bolt flange · SC20 mmShaft diameter125876Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 31.2 mm
Flange length B: 112.0 mm
Overall depth C: 34.0 mm
Bolt-centre distance D: 89.7 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 9.1 mm
Drawing dimension L: 28.4 mm
Flange width M: 60.5 mm
Drawing dimension N: 38.1 mm
Assembly mass: 0.5 kg

F2B-SC-014Two-bolt flange · SC7/8 inShaft diameter124171Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange length B: 4.88 in
Overall depth C: 1.37 in
Bolt-centre distance D: 3.89 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.52 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Flange width M: 2.75 in
Drawing dimension N: 1.44 in
Assembly mass: 1.6 lb

F2B-SC-015Two-bolt flange · SC15/16 inShaft diameter124172Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange length B: 4.88 in
Overall depth C: 1.37 in
Bolt-centre distance D: 3.89 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.52 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Flange width M: 2.75 in
Drawing dimension N: 1.44 in
Assembly mass: 1.5 lb

F2B-SC-100Two-bolt flange · SC1 inShaft diameter124173Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange length B: 4.88 in
Overall depth C: 1.37 in
Bolt-centre distance D: 3.89 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.52 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Flange width M: 2.75 in
Drawing dimension N: 1.44 in
Assembly mass: 1.4 lb

F2B-SC-25MTwo-bolt flange · SC25 mmShaft diameter125877Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 34.0 mm
Flange length B: 124.0 mm
Overall depth C: 34.8 mm
Bolt-centre distance D: 98.8 mm
Mounting bolt F: M10
Drawing dimension H: 13.2 mm
Drawing dimension J: 10.7 mm
Drawing dimension L: 33.5 mm
Flange width M: 69.9 mm
Drawing dimension N: 36.6 mm
Assembly mass: 0.6 kg

F2B-SC-101Two-bolt flange · SC1-1/16 inShaft diameter124410Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange length B: 5.56 in
Overall depth C: 1.56 in
Bolt-centre distance D: 4.59 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Flange width M: 3.13 in
Drawing dimension N: 1.56 in
Assembly mass: 2.3 lb

F2B-SC-102Two-bolt flange · SC1-1/8 inShaft diameter124274Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange length B: 5.56 in
Overall depth C: 1.56 in
Bolt-centre distance D: 4.59 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Flange width M: 3.13 in
Drawing dimension N: 1.56 in
Assembly mass: 2.2 lb

F2B-SC-103Two-bolt flange · SC1-3/16 inShaft diameter124275Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange length B: 5.56 in
Overall depth C: 1.56 in
Bolt-centre distance D: 4.59 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Flange width M: 3.13 in
Drawing dimension N: 1.56 in
Assembly mass: 2.1 lb

F2B-SC-104STwo-bolt flange · SC1-1/4 inShaft diameter123172Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange length B: 5.56 in
Overall depth C: 1.56 in
Bolt-centre distance D: 4.59 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Flange width M: 3.13 in
Drawing dimension N: 1.56 in
Assembly mass: 2.0 lb

F2B-SC-30MTwo-bolt flange · SC30 mmShaft diameter125878Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Flange length B: 141.2 mm
Overall depth C: 39.6 mm
Bolt-centre distance D: 116.7 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 12.4 mm
Drawing dimension L: 39.9 mm
Flange width M: 79.5 mm
Drawing dimension N: 39.6 mm
Assembly mass: 1.0 kg

F2B-SC-104Two-bolt flange · SC1-1/4 inShaft diameter124276Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange length B: 6.13 in
Overall depth C: 1.75 in
Bolt-centre distance D: 5.12 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Flange width M: 3.75 in
Drawing dimension N: 1.84 in
Assembly mass: 3.5 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-27, B1-28, B1-32, B1-33 (PDF pages 38, 39, 43, 44). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F2B-SC-105Two-bolt flange · SC1-5/16 inShaft diameter124411Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange length B: 6.13 in
Overall depth C: 1.75 in
Bolt-centre distance D: 5.12 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Flange width M: 3.75 in
Drawing dimension N: 1.84 in
Assembly mass: 3.4 lb

F2B-SC-106Two-bolt flange · SC1-3/8 inShaft diameter124277Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange length B: 6.13 in
Overall depth C: 1.75 in
Bolt-centre distance D: 5.12 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Flange width M: 3.75 in
Drawing dimension N: 1.84 in
Assembly mass: 3.2 lb

F2B-SC-107Two-bolt flange · SC1-7/16 inShaft diameter124278Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange length B: 6.13 in
Overall depth C: 1.75 in
Bolt-centre distance D: 5.12 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Flange width M: 3.75 in
Drawing dimension N: 1.84 in
Assembly mass: 3.1 lb

F2B-SC-35MTwo-bolt flange · SC35 mmShaft diameter125879Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Flange length B: 155.7 mm
Overall depth C: 44.5 mm
Bolt-centre distance D: 130.0 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 13.5 mm
Drawing dimension L: 46.7 mm
Flange width M: 95.3 mm
Drawing dimension N: 46.7 mm
Assembly mass: 1.5 kg

F2B-SC-108Two-bolt flange · SC1-1/2 inShaft diameter124268Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 6.75 in
Overall depth C: 1.97 in
Bolt-centre distance D: 5.66 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Flange width M: 4.13 in
Drawing dimension N: 1.83 in
Assembly mass: 4.1 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-29, B1-30 (PDF pages 40, 41). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F2B-SC-110Two-bolt flange · SC1-5/8 inShaft diameter124412Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 6.75 in
Overall depth C: 1.97 in
Bolt-centre distance D: 5.66 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Flange width M: 4.13 in
Drawing dimension N: 1.83 in
Assembly mass: 4.0 lb

F2B-SC-40MTwo-bolt flange · SC40 mmShaft diameter125880Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange length B: 171.5 mm
Overall depth C: 50.0 mm
Bolt-centre distance D: 143.8 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 52.1 mm
Flange width M: 104.9 mm
Drawing dimension N: 46.5 mm
Assembly mass: 1.8 kg

F2B-SC-110LTwo-bolt flange · SC1-5/8 inShaft diameter125171Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.06 in
Overall depth C: 1.99 in
Bolt-centre distance D: 5.84 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Flange width M: 4.38 in
Drawing dimension N: 1.91 in
Assembly mass: 5.2 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-29, B1-30, B1-32, B1-33 (PDF pages 40, 41, 43, 44). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F2B-SC-111Two-bolt flange · SC1-11/16 inShaft diameter124279Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.06 in
Overall depth C: 1.99 in
Bolt-centre distance D: 5.84 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Flange width M: 4.38 in
Drawing dimension N: 1.91 in
Assembly mass: 5.0 lb

F2B-SC-112Two-bolt flange · SC1-3/4 inShaft diameter124413Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.06 in
Overall depth C: 1.99 in
Bolt-centre distance D: 5.84 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Flange width M: 4.38 in
Drawing dimension N: 1.91 in
Assembly mass: 4.9 lb

F2B-SC-113Two-bolt flange · SC1-13/16 inShaft diameter124280Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.06 in
Overall depth C: 1.99 in
Bolt-centre distance D: 5.84 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Flange width M: 4.38 in
Drawing dimension N: 1.91 in
Assembly mass: 4.7 lb

F2B-SC-115Two-bolt flange · SC1-15/16 inShaft diameter124269Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.44 in
Overall depth C: 2.02 in
Bolt-centre distance D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Flange width M: 4.56 in
Drawing dimension N: 2.03 in
Assembly mass: 5.4 lb

F2B-SC-200Two-bolt flange · SC2 inShaft diameter124270Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.44 in
Overall depth C: 2.02 in
Bolt-centre distance D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Flange width M: 4.56 in
Drawing dimension N: 2.03 in
Assembly mass: 5.2 lb

F2B-SC-50MTwo-bolt flange · SC50 mmShaft diameter125882Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange length B: 189.0 mm
Overall depth C: 51.3 mm
Bolt-centre distance D: 157.2 mm
Mounting bolt F: M16
Drawing dimension H: 16.0 mm
Drawing dimension J: 14.0 mm
Drawing dimension L: 61.7 mm
Flange width M: 115.8 mm
Drawing dimension N: 51.6 mm
Assembly mass: 2.5 kg

F2B-SC-203Two-bolt flange · SC2-3/16 inShaft diameter124034Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange length B: 8.63 in
Overall depth C: 2.28 in
Bolt-centre distance D: 7.25 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.67 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Flange width M: 5.25 in
Drawing dimension N: 2.27 in
Assembly mass: 6.5 lb

F2B-SC-204Two-bolt flange · SC2-1/4 inShaft diameter124373Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange length B: 8.63 in
Overall depth C: 2.28 in
Bolt-centre distance D: 7.25 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.67 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Flange width M: 5.25 in
Drawing dimension N: 2.27 in
Assembly mass: 6.3 lb

F2B-SC-55MTwo-bolt flange · SC55 mmShaft diameter124942Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Flange length B: 219.2 mm
Overall depth C: 57.9 mm
Bolt-centre distance D: 184.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.0 mm
Drawing dimension J: 17.3 mm
Drawing dimension L: 68.8 mm
Flange width M: 133.4 mm
Drawing dimension N: 57.7 mm
Assembly mass: 3.0 kg

F2B-SC-207Two-bolt flange · SC2-7/16 inShaft diameter053175Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Flange length B: 9.81 in
Overall depth C: 2.38 in
Bolt-centre distance D: 7.96 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.81 in
Drawing dimension J: 0.66 in
Drawing dimension L: 2.97 in
Flange width M: 5.50 in
Drawing dimension N: 2.47 in
Assembly mass: 7.0 lb

F2B-SC-60MTwo-bolt flange · SC60 mmShaft diameter053883Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Flange length B: 249.2 mm
Overall depth C: 60.5 mm
Bolt-centre distance D: 202.1 mm
Mounting bolt F: M22
Drawing dimension H: 20.6 mm
Drawing dimension J: 16.8 mm
Drawing dimension L: 75.4 mm
Flange width M: 139.7 mm
Drawing dimension N: 62.7 mm
Assembly mass: 3.4 kg

F2B-SCM-100Two-bolt flange · SCM1 inShaft diameter126284Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange length B: 5.56 in
Overall depth C: 1.56 in
Bolt-centre distance D: 4.59 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Flange width M: 3.13 in
Drawing dimension N: 1.56 in
Assembly mass: 2.4 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-32, B1-33 (PDF pages 43, 44). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F2B-SCM-25MTwo-bolt flange · SCM25 mmShaft diameter125954Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Flange length B: 141.2 mm
Overall depth C: 39.6 mm
Bolt-centre distance D: 116.7 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 12.4 mm
Drawing dimension L: 39.9 mm
Flange width M: 79.5 mm
Drawing dimension N: 39.6 mm
Assembly mass: 1.0 kg

F2B-SCM-103Two-bolt flange · SCM1-3/16 inShaft diameter126285Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange length B: 6.13 in
Overall depth C: 1.75 in
Bolt-centre distance D: 5.12 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Flange width M: 3.75 in
Drawing dimension N: 1.84 in
Assembly mass: 3.6 lb

F2B-SCM-30MTwo-bolt flange · SCM30 mmShaft diameter125955Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Flange length B: 155.7 mm
Overall depth C: 44.5 mm
Bolt-centre distance D: 130.0 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 13.5 mm
Drawing dimension L: 46.7 mm
Flange width M: 95.3 mm
Drawing dimension N: 46.7 mm
Assembly mass: 1.6 kg

F2B-SCM-107Two-bolt flange · SCM1-7/16 inShaft diameter126287Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 6.75 in
Overall depth C: 1.98 in
Bolt-centre distance D: 5.66 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Flange width M: 4.13 in
Drawing dimension N: 1.83 in
Assembly mass: 4.1 lb

F2B-SCM-35MTwo-bolt flange · SCM35 mmShaft diameter125956Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange length B: 171.5 mm
Overall depth C: 50.3 mm
Bolt-centre distance D: 143.8 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 52.1 mm
Flange width M: 104.9 mm
Drawing dimension N: 46.5 mm
Assembly mass: 1.9 kg

F2B-SCM-108Two-bolt flange · SCM1-1/2 inShaft diameter126288Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.06 in
Overall depth C: 1.99 in
Bolt-centre distance D: 5.84 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Flange width M: 4.38 in
Drawing dimension N: 1.91 in
Assembly mass: 5.3 lb

F2B-SCM-40MTwo-bolt flange · SCM40 mmShaft diameter125957Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange length B: 179.3 mm
Overall depth C: 50.5 mm
Bolt-centre distance D: 148.3 mm
Mounting bolt F: M14
Drawing dimension H: 16.0 mm
Drawing dimension J: 15.0 mm
Drawing dimension L: 56.4 mm
Flange width M: 111.3 mm
Drawing dimension N: 48.5 mm
Assembly mass: 2.3 kg

F2B-SCM-111Two-bolt flange · SCM1-11/16 inShaft diameter126289Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.44 in
Overall depth C: 2.02 in
Bolt-centre distance D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Flange width M: 4.56 in
Drawing dimension N: 2.03 in
Assembly mass: 5.8 lb

F2B-SCM-112Two-bolt flange · SCM1-3/4 inShaft diameter126290Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange length B: 7.44 in
Overall depth C: 2.02 in
Bolt-centre distance D: 6.19 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Flange width M: 4.56 in
Drawing dimension N: 2.03 in
Assembly mass: 5.6 lb

F2B-SCM-45MTwo-bolt flange · SCM45 mmShaft diameter125958Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange length B: 189.0 mm
Overall depth C: 51.3 mm
Bolt-centre distance D: 157.2 mm
Mounting bolt F: M16
Drawing dimension H: 16.0 mm
Drawing dimension J: 14.0 mm
Drawing dimension L: 61.7 mm
Flange width M: 115.8 mm
Drawing dimension N: 51.6 mm
Assembly mass: 2.6 kg

F2B-SCM-115Two-bolt flange · SCM1-15/16 inShaft diameter126292Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange length B: 8.63 in
Overall depth C: 2.28 in
Bolt-centre distance D: 7.25 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.67 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Flange width M: 5.25 in
Drawing dimension N: 2.27 in
Assembly mass: 6.7 lb

F2B-SCM-50MTwo-bolt flange · SCM50 mmShaft diameter125960Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Flange length B: 219.2 mm
Overall depth C: 57.9 mm
Bolt-centre distance D: 184.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.0 mm
Drawing dimension J: 17.3 mm
Drawing dimension L: 68.8 mm
Flange width M: 133.4 mm
Drawing dimension N: 57.7 mm
Assembly mass: 2.9 kg

F2B-SCM-203Two-bolt flange · SCM2-3/16 inShaft diameter062746Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Flange length B: 9.81 in
Overall depth C: 2.38 in
Bolt-centre distance D: 7.96 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.81 in
Drawing dimension J: 0.66 in
Drawing dimension L: 2.97 in
Flange width M: 5.50 in
Drawing dimension N: 2.47 in
Assembly mass: 7.4 lb

F2B-SCM-55MTwo-bolt flange · SCM55 mmShaft diameterOrder-only referenceNumeric part number not statedDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Flange length B: 249.2 mm
Overall depth C: 60.5 mm
Bolt-centre distance D: 202.1 mm
Mounting bolt F: M22
Drawing dimension H: 20.6 mm
Drawing dimension J: 16.8 mm
Drawing dimension L: 75.4 mm
Flange width M: 139.7 mm
Drawing dimension N: 62.7 mm
Assembly mass: 3.2 kg

F4B-SC-008Four-bolt flange · SC1/2 inShaft diameter124048Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Flange side B: 3.00 in
Overall depth C: 1.17 in
Bolt-centre pitch D: 2.13 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.32 in
Drawing dimension L: 0.96 in
Drawing dimension N: 1.69 in
Assembly mass: 1.1 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-44, B1-45 (PDF pages 55, 56). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F4B-SC-010Four-bolt flange · SC5/8 inShaft diameter124049Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.00 in
Flange side B: 3.00 in
Overall depth C: 1.17 in
Bolt-centre pitch D: 2.13 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.32 in
Drawing dimension L: 0.96 in
Drawing dimension N: 1.69 in
Assembly mass: 1.0 lb

F4B-SC-17MFour-bolt flange · SC17 mmShaft diameter125885Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 25.4 mm
Flange side B: 76.2 mm
Overall depth C: 29.7 mm
Bolt-centre pitch D: 54.0 mm
Mounting bolt F: M10
Drawing dimension H: 11.2 mm
Drawing dimension J: 8.1 mm
Drawing dimension L: 24.4 mm
Drawing dimension N: 42.9 mm
Assembly mass: 0.5 kg

F4B-SC-008LFour-bolt flange · SC1/2 inShaft diameter124098Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange side B: 3.38 in
Overall depth C: 1.34 in
Bolt-centre pitch D: 2.5 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Drawing dimension N: 1.94 in
Assembly mass: 1.8 lb

F4B-SC-010LFour-bolt flange · SC5/8 inShaft diameter124099Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange side B: 3.38 in
Overall depth C: 1.34 in
Bolt-centre pitch D: 2.5 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Drawing dimension N: 1.94 in
Assembly mass: 1.7 lb

F4B-SC-012Four-bolt flange · SC3/4 inShaft diameter124100Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange side B: 3.38 in
Overall depth C: 1.34 in
Bolt-centre pitch D: 2.5 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Drawing dimension N: 1.94 in
Assembly mass: 1.6 lb

F4B-SC-013Four-bolt flange · SC13/16 inShaft diameter124567Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Flange side B: 3.38 in
Overall depth C: 1.34 in
Bolt-centre pitch D: 2.5 in
Mounting bolt F: 3/8 in
Drawing dimension H: 0.44 in
Drawing dimension J: 0.36 in
Drawing dimension L: 1.12 in
Drawing dimension N: 1.94 in
Assembly mass: 1.5 lb

F4B-SC-20MFour-bolt flange · SC20 mmShaft diameter125886Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 31.2 mm
Flange side B: 85.9 mm
Overall depth C: 34.0 mm
Bolt-centre pitch D: 63.5 mm
Mounting bolt F: M10
Drawing dimension H: 11.2 mm
Drawing dimension J: 9.1 mm
Drawing dimension L: 28.4 mm
Drawing dimension N: 49.3 mm
Assembly mass: 0.8 kg

F4B-SC-014Four-bolt flange · SC7/8 inShaft diameter124101Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange side B: 3.75 in
Overall depth C: 1.37 in
Bolt-centre pitch D: 2.75 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Drawing dimension N: 2.06 in
Assembly mass: 2.0 lb

F4B-SC-015Four-bolt flange · SC15/16 inShaft diameter124102Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange side B: 3.75 in
Overall depth C: 1.37 in
Bolt-centre pitch D: 2.75 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Drawing dimension N: 2.06 in
Assembly mass: 1.9 lb

F4B-SC-100Four-bolt flange · SC1 inShaft diameter124103Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Flange side B: 3.75 in
Overall depth C: 1.37 in
Bolt-centre pitch D: 2.75 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.42 in
Drawing dimension L: 1.32 in
Drawing dimension N: 2.06 in
Assembly mass: 1.8 lb

F4B-SC-25MFour-bolt flange · SC25 mmShaft diameter125887Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 34.0 mm
Flange side B: 95.3 mm
Overall depth C: 34.8 mm
Bolt-centre pitch D: 69.9 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 10.7 mm
Drawing dimension L: 33.5 mm
Drawing dimension N: 52.3 mm
Assembly mass: 0.9 kg

F4B-SC-101Four-bolt flange · SC1-1/16 inShaft diameter124218Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange side B: 4.25 in
Overall depth C: 1.56 in
Bolt-centre pitch D: 3.25 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Drawing dimension N: 2.19 in
Assembly mass: 2.9 lb

F4B-SC-102Four-bolt flange · SC1-1/8 inShaft diameter124204Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange side B: 4.25 in
Overall depth C: 1.56 in
Bolt-centre pitch D: 3.25 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Drawing dimension N: 2.19 in
Assembly mass: 2.8 lb

F4B-SC-103Four-bolt flange · SC1-3/16 inShaft diameter124205Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange side B: 4.25 in
Overall depth C: 1.56 in
Bolt-centre pitch D: 3.25 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Drawing dimension N: 2.19 in
Assembly mass: 2.7 lb

F4B-SC-104SFour-bolt flange · SC1-1/4 inShaft diameter123173Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange side B: 4.25 in
Overall depth C: 1.56 in
Bolt-centre pitch D: 3.25 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Drawing dimension N: 2.19 in
Assembly mass: 2.6 lb

F4B-SC-30MFour-bolt flange · SC30 mmShaft diameter125888Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Flange side B: 108.0 mm
Overall depth C: 39.6 mm
Bolt-centre pitch D: 82.6 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 12.4 mm
Drawing dimension L: 39.9 mm
Drawing dimension N: 55.6 mm
Assembly mass: 1.3 kg

F4B-SC-104Four-bolt flange · SC1-1/4 inShaft diameter124206Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange side B: 4.75 in
Overall depth C: 1.75 in
Bolt-centre pitch D: 3.63 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Drawing dimension N: 2.44 in
Assembly mass: 4.0 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-44, B1-45, B1-48, B1-49 (PDF pages 55, 56, 59, 60). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F4B-SC-105Four-bolt flange · SC1-5/16 inShaft diameter124219Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange side B: 4.75 in
Overall depth C: 1.75 in
Bolt-centre pitch D: 3.63 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Drawing dimension N: 2.44 in
Assembly mass: 3.9 lb

F4B-SC-106Four-bolt flange · SC1-3/8 inShaft diameter124207Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange side B: 4.75 in
Overall depth C: 1.75 in
Bolt-centre pitch D: 3.63 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Drawing dimension N: 2.44 in
Assembly mass: 3.8 lb

F4B-SC-107Four-bolt flange · SC1-7/16 inShaft diameter124208Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange side B: 4.75 in
Overall depth C: 1.75 in
Bolt-centre pitch D: 3.63 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Drawing dimension N: 2.44 in
Assembly mass: 3.7 lb

F4B-SC-35MFour-bolt flange · SC35 mmShaft diameter125889Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Flange side B: 120.7 mm
Overall depth C: 44.5 mm
Bolt-centre pitch D: 92.1 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 13.5 mm
Drawing dimension L: 46.7 mm
Drawing dimension N: 62.0 mm
Assembly mass: 1.7 kg

F4B-SC-108Four-bolt flange · SC1-1/2 inShaft diameter124209Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.13 in
Overall depth C: 1.98 in
Bolt-centre pitch D: 4.00 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Drawing dimension N: 2.38 in
Assembly mass: 4.8 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-46, B1-47 (PDF pages 57, 58). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F4B-SC-110Four-bolt flange · SC1-5/8 inShaft diameter124210Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.13 in
Overall depth C: 1.98 in
Bolt-centre pitch D: 4.00 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Drawing dimension N: 2.38 in
Assembly mass: 4.7 lb

F4B-SC-40MFour-bolt flange · SC40 mmShaft diameter125890Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 130.3 mm
Overall depth C: 50.3 mm
Bolt-centre pitch D: 101.6 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 52.1 mm
Drawing dimension N: 60.5 mm
Assembly mass: 2.1 kg

F4B-SC-110LFour-bolt flange · SC1-5/8 inShaft diameter125170Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.38 in
Overall depth C: 1.99 in
Bolt-centre pitch D: 4.13 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Drawing dimension N: 2.75 in
Assembly mass: 6.1 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-46, B1-47, B1-48, B1-49 (PDF pages 57, 58, 59, 60). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F4B-SC-111Four-bolt flange · SC1-11/16 inShaft diameter124211Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.38 in
Overall depth C: 1.99 in
Bolt-centre pitch D: 4.13 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Drawing dimension N: 2.75 in
Assembly mass: 6.0 lb

F4B-SC-112Four-bolt flange · SC1-3/4 inShaft diameter124212Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.38 in
Overall depth C: 1.99 in
Bolt-centre pitch D: 4.13 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Drawing dimension N: 2.75 in
Assembly mass: 5.9 lb

F4B-SC-45MFour-bolt flange · SC45 mmShaft diameter125891Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 136.7 mm
Overall depth C: 50.5 mm
Bolt-centre pitch D: 104.8 mm
Mounting bolt F: M12
Drawing dimension H: 16.0 mm
Drawing dimension J: 15.0 mm
Drawing dimension L: 56.4 mm
Drawing dimension N: 69.9 mm
Assembly mass: 2.7 kg

F4B-SC-115Four-bolt flange · SC1-15/16 inShaft diameter124213Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.63 in
Overall depth C: 2.02 in
Bolt-centre pitch D: 4.38 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Drawing dimension N: 2.88 in
Assembly mass: 6.7 lb

F4B-SC-200Four-bolt flange · SC2 inShaft diameter124214Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.63 in
Overall depth C: 2.02 in
Bolt-centre pitch D: 4.38 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Drawing dimension N: 2.88 in
Assembly mass: 6.6 lb

F4B-SC-50MFour-bolt flange · SC50 mmShaft diameter125892Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 143.0 mm
Overall depth C: 51.3 mm
Bolt-centre pitch D: 111.1 mm
Mounting bolt F: M12
Drawing dimension H: 16.0 mm
Drawing dimension J: 14.0 mm
Drawing dimension L: 61.7 mm
Drawing dimension N: 73.2 mm
Assembly mass: 3.0 kg

F4B-SCM-200Four-bolt flange · SCM2 inShaft diameter126192Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange side B: 6.50 in
Overall depth C: 2.28 in
Bolt-centre pitch D: 5.13 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Drawing dimension N: 3.25 in
Assembly mass: 9.3 lb

F4B-SC-203Four-bolt flange · SC2-3/16 inShaft diameter124215Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange side B: 6.50 in
Overall depth C: 2.28 in
Bolt-centre pitch D: 5.13 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Drawing dimension N: 3.25 in
Assembly mass: 9.0 lb

F4B-SC-204Four-bolt flange · SC2-1/4 inShaft diameter124216Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange side B: 6.50 in
Overall depth C: 2.28 in
Bolt-centre pitch D: 5.13 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Drawing dimension N: 3.25 in
Assembly mass: 8.9 lb

F4B-SC-55MFour-bolt flange · SC55 mmShaft diameter125893Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Flange side B: 165.1 mm
Overall depth C: 57.9 mm
Bolt-centre pitch D: 130.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 17.3 mm
Drawing dimension L: 68.8 mm
Drawing dimension N: 82.6 mm
Assembly mass: 4.1 kg

F4B-SCM-204Four-bolt flange · SCM2-1/4 inShaft diameter126283Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Flange side B: 6.88 in
Overall depth C: 2.38 in
Bolt-centre pitch D: 5.63 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.66 in
Drawing dimension L: 2.97 in
Drawing dimension N: 3.50 in
Assembly mass: 11.1 lb

F4B-SC-207Four-bolt flange · SC2-7/16 inShaft diameter124217Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Flange side B: 6.88 in
Overall depth C: 2.38 in
Bolt-centre pitch D: 5.63 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.66 in
Drawing dimension L: 2.97 in
Drawing dimension N: 3.50 in
Assembly mass: 10.6 lb

F4B-SC-60MFour-bolt flange · SC60 mmShaft diameter125894Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Flange side B: 174.8 mm
Overall depth C: 60.5 mm
Bolt-centre pitch D: 142.9 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 16.8 mm
Drawing dimension L: 75.4 mm
Drawing dimension N: 88.9 mm
Assembly mass: 6.0 kg

F4B-SCM-208Four-bolt flange · SCM2-1/2 inShaft diameter126195Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Flange side B: 7.38 in
Overall depth C: 2.78 in
Bolt-centre pitch D: 5.88 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.60 in
Drawing dimension L: 3.31 in
Drawing dimension N: 3.69 in
Assembly mass: 16.0 lb

F4B-SC-211Four-bolt flange · SC2-11/16 inShaft diameter124261Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Flange side B: 7.38 in
Overall depth C: 2.78 in
Bolt-centre pitch D: 5.88 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.60 in
Drawing dimension L: 3.31 in
Drawing dimension N: 3.69 in
Assembly mass: 15.4 lb

F4B-SC-70MFour-bolt flange · SC70 mmShaft diameter125895Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Flange side B: 187.5 mm
Overall depth C: 70.6 mm
Bolt-centre pitch D: 149.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 15.2 mm
Drawing dimension L: 84.1 mm
Drawing dimension N: 93.7 mm
Assembly mass: 6.9 kg

F4B-SC-215Four-bolt flange · SC2-15/16 inShaft diameter124220Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Flange side B: 7.75 in
Overall depth C: 2.88 in
Bolt-centre pitch D: 6.00 in
Mounting bolt F: 3/4 in
Drawing dimension H: 1.00 in
Drawing dimension J: 0.63 in
Drawing dimension L: 3.62 in
Drawing dimension N: 3.88 in
Assembly mass: 17.6 lb

F4B-SC-75MFour-bolt flange · SC75 mmShaft diameter125896Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Flange side B: 196.9 mm
Overall depth C: 73.2 mm
Bolt-centre pitch D: 152.4 mm
Mounting bolt F: M18
Drawing dimension H: 25.4 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 91.9 mm
Drawing dimension N: 98.6 mm
Assembly mass: 8.0 kg

F4B-SCM-100Four-bolt flange · SCM1 inShaft diameter126226Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Flange side B: 4.25 in
Overall depth C: 1.56 in
Bolt-centre pitch D: 3.25 in
Mounting bolt F: 7/16 in
Drawing dimension H: 0.50 in
Drawing dimension J: 0.49 in
Drawing dimension L: 1.57 in
Drawing dimension N: 2.19 in
Assembly mass: 3.0 lb

Source: Dodge Mounted Ball Bearings, printed pages B1-48, B1-49 (PDF pages 59, 60). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

F4B-SCM-25MFour-bolt flange · SCM25 mmShaft diameter125965Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Flange side B: 108.0 mm
Overall depth C: 39.6 mm
Bolt-centre pitch D: 82.6 mm
Mounting bolt F: M10
Drawing dimension H: 12.7 mm
Drawing dimension J: 12.4 mm
Drawing dimension L: 39.9 mm
Drawing dimension N: 55.6 mm
Assembly mass: 1.3 kg

F4B-SCM-103Four-bolt flange · SCM1-3/16 inShaft diameter126227Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Flange side B: 4.75 in
Overall depth C: 1.75 in
Bolt-centre pitch D: 3.63 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.53 in
Drawing dimension L: 1.84 in
Drawing dimension N: 2.44 in
Assembly mass: 4.1 lb

F4B-SCM-30MFour-bolt flange · SCM30 mmShaft diameter125966Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Flange side B: 120.7 mm
Overall depth C: 44.5 mm
Bolt-centre pitch D: 92.1 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 13.5 mm
Drawing dimension L: 46.7 mm
Drawing dimension N: 62.0 mm
Assembly mass: 1.4 kg

F4B-SCM-107Four-bolt flange · SCM1-7/16 inShaft diameter126187Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.13 in
Overall depth C: 1.98 in
Bolt-centre pitch D: 4.00 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.56 in
Drawing dimension J: 0.63 in
Drawing dimension L: 2.05 in
Drawing dimension N: 2.38 in
Assembly mass: 5.0 lb

F4B-SCM-35MFour-bolt flange · SCM35 mmShaft diameter125967Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 130.3 mm
Overall depth C: 50.3 mm
Bolt-centre pitch D: 101.6 mm
Mounting bolt F: M12
Drawing dimension H: 14.2 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 52.1 mm
Drawing dimension N: 60.5 mm
Assembly mass: 2.1 kg

F4B-SCM-108Four-bolt flange · SCM1-1/2 inShaft diameter126188Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.38 in
Overall depth C: 1.99 in
Bolt-centre pitch D: 4.13 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.59 in
Drawing dimension L: 2.22 in
Drawing dimension N: 2.75 in
Assembly mass: 6.1 lb

F4B-SCM-40MFour-bolt flange · SCM40 mmShaft diameter125968Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 136.7 mm
Overall depth C: 50.5 mm
Bolt-centre pitch D: 104.8 mm
Mounting bolt F: M12
Drawing dimension H: 16.0 mm
Drawing dimension J: 15.0 mm
Drawing dimension L: 56.4 mm
Drawing dimension N: 69.9 mm
Assembly mass: 2.7 kg

F4B-SCM-111Four-bolt flange · SCM1-11/16 inShaft diameter126189Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.63 in
Overall depth C: 2.02 in
Bolt-centre pitch D: 4.38 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Drawing dimension N: 2.88 in
Assembly mass: 7.1 lb

F4B-SCM-112Four-bolt flange · SCM1-3/4 inShaft diameter126190Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Flange side B: 5.63 in
Overall depth C: 2.02 in
Bolt-centre pitch D: 4.38 in
Mounting bolt F: 1/2 in
Drawing dimension H: 0.63 in
Drawing dimension J: 0.55 in
Drawing dimension L: 2.43 in
Drawing dimension N: 2.88 in
Assembly mass: 6.9 lb

F4B-SCM-45MFour-bolt flange · SCM45 mmShaft diameter125969Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Flange side B: 143.0 mm
Overall depth C: 51.3 mm
Bolt-centre pitch D: 111.1 mm
Mounting bolt F: M12
Drawing dimension H: 16.0 mm
Drawing dimension J: 14.0 mm
Drawing dimension L: 61.7 mm
Drawing dimension N: 73.2 mm
Assembly mass: 3.0 kg

F4B-SCM-115Four-bolt flange · SCM1-15/16 inShaft diameter126191Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Flange side B: 6.50 in
Overall depth C: 2.28 in
Bolt-centre pitch D: 5.13 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.68 in
Drawing dimension L: 2.71 in
Drawing dimension N: 3.25 in
Assembly mass: 9.5 lb

F4B-SCM-50MFour-bolt flange · SCM50 mmShaft diameter125970Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Flange side B: 165.1 mm
Overall depth C: 57.9 mm
Bolt-centre pitch D: 130.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 17.3 mm
Drawing dimension L: 68.8 mm
Drawing dimension N: 82.6 mm
Assembly mass: 4.1 kg

F4B-SCM-203Four-bolt flange · SCM2-3/16 inShaft diameter126193Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Flange side B: 6.88 in
Overall depth C: 2.38 in
Bolt-centre pitch D: 5.63 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.66 in
Drawing dimension L: 2.97 in
Drawing dimension N: 3.50 in
Assembly mass: 11.3 lb

F4B-SCM-55MFour-bolt flange · SCM55 mmShaft diameter125971Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Flange side B: 174.8 mm
Overall depth C: 60.5 mm
Bolt-centre pitch D: 142.9 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 16.8 mm
Drawing dimension L: 75.4 mm
Drawing dimension N: 88.9 mm
Assembly mass: 6.0 kg

F4B-SCM-207Four-bolt flange · SCM2-7/16 inShaft diameter126194Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Flange side B: 7.38 in
Overall depth C: 2.78 in
Bolt-centre pitch D: 5.88 in
Mounting bolt F: 5/8 in
Drawing dimension H: 0.69 in
Drawing dimension J: 0.60 in
Drawing dimension L: 3.31 in
Drawing dimension N: 3.69 in
Assembly mass: 16.2 lb

F4B-SCM-65MFour-bolt flange · SCM65 mmShaft diameter125972Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Flange side B: 187.5 mm
Overall depth C: 70.6 mm
Bolt-centre pitch D: 149.2 mm
Mounting bolt F: M16
Drawing dimension H: 17.5 mm
Drawing dimension J: 15.2 mm
Drawing dimension L: 84.1 mm
Drawing dimension N: 93.7 mm
Assembly mass: 7.3 kg

F4B-SCM-211Four-bolt flange · SCM2-11/16 inShaft diameter126186Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Flange side B: 7.75 in
Overall depth C: 2.88 in
Bolt-centre pitch D: 6.00 in
Mounting bolt F: 3/4 in
Drawing dimension H: 1.00 in
Drawing dimension J: 0.63 in
Drawing dimension L: 3.62 in
Drawing dimension N: 3.88 in
Assembly mass: 18.3 lb

F4B-SCM-70MFour-bolt flange · SCM70 mmShaft diameter125973Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Flange side B: 196.9 mm
Overall depth C: 73.2 mm
Bolt-centre pitch D: 152.4 mm
Mounting bolt F: M18
Drawing dimension H: 25.4 mm
Drawing dimension J: 16.0 mm
Drawing dimension L: 91.9 mm
Drawing dimension N: 98.6 mm
Assembly mass: 8.0 kg

F4B-SCM-215Four-bolt flange · SCM2-15/16 inShaft diameter126196Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Flange side B: 7.75 in
Overall depth C: 3.09 in
Bolt-centre pitch D: 6.00 in
Mounting bolt F: 3/4 in
Drawing dimension H: 0.88 in
Drawing dimension J: 0.59 in
Drawing dimension L: 3.83 in
Drawing dimension N: 4.09 in
Assembly mass: 21.5 lb

F4B-SCM-300Four-bolt flange · SCM3 inShaft diameter126197Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Flange side B: 7.75 in
Overall depth C: 3.09 in
Bolt-centre pitch D: 6.00 in
Mounting bolt F: 3/4 in
Drawing dimension H: 0.88 in
Drawing dimension J: 0.59 in
Drawing dimension L: 3.83 in
Drawing dimension N: 4.09 in
Assembly mass: 21.2 lb

F4B-SCM-75MFour-bolt flange · SCM75 mmShaft diameter125974Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 60.5 mm
Flange side B: 196.9 mm
Overall depth C: 78.5 mm
Bolt-centre pitch D: 152.4 mm
Mounting bolt F: M18
Drawing dimension H: 22.4 mm
Drawing dimension J: 15.0 mm
Drawing dimension L: 97.3 mm
Drawing dimension N: 103.9 mm
Assembly mass: 9.4 kg

F4B-SCM-307Four-bolt flange · SCM3-7/16 inShaft diameter126198Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.56 in
Flange side B: 8.44 in
Overall depth C: 3.38 in
Bolt-centre pitch D: 6.75 in
Mounting bolt F: 3/4 in
Drawing dimension H: 1.00 in
Drawing dimension J: 0.60 in
Drawing dimension L: 4.35 in
Drawing dimension N: 4.63 in
Assembly mass: 28.0 lb

F4B-SCM-308Four-bolt flange · SCM3-1/2 inShaft diameter126199Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.56 in
Flange side B: 8.44 in
Overall depth C: 3.38 in
Bolt-centre pitch D: 6.75 in
Mounting bolt F: 3/4 in
Drawing dimension H: 1.00 in
Drawing dimension J: 0.60 in
Drawing dimension L: 4.35 in
Drawing dimension N: 4.63 in
Assembly mass: 27.4 lb

F4B-SCM-85MFour-bolt flange · SCM85 mmShaft diameter125975Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 65.0 mm
Flange side B: 214.4 mm
Overall depth C: 85.9 mm
Bolt-centre pitch D: 171.5 mm
Mounting bolt F: M18
Drawing dimension H: 25.4 mm
Drawing dimension J: 15.2 mm
Drawing dimension L: 110.5 mm
Drawing dimension N: 117.6 mm
Assembly mass: 12.2 kg

WSTU-SC-008Wide-slot take-up · SC1/2 inShaft diameter125343Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Drawing dimension B: 3.69 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.38 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.25 in
Drawing dimension L: 1.12 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension T: 1.38 in
Assembly mass: 2.1 lb
Take-up frame: WS300

Source: Dodge Mounted Ball Bearings, printed pages B1-62, B1-63 (PDF pages 73, 74). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SC-010Wide-slot take-up · SC5/8 inShaft diameter125344Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Drawing dimension B: 3.69 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.38 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.25 in
Drawing dimension L: 1.12 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension T: 1.38 in
Assembly mass: 2.0 lb
Take-up frame: WS300

WSTU-SC-012Wide-slot take-up · SC3/4 inShaft diameter125010Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.23 in
Drawing dimension B: 3.69 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.38 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.25 in
Drawing dimension L: 1.12 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.50 in
Drawing dimension S: 0.73 in
Drawing dimension T: 1.38 in
Assembly mass: 1.9 lb
Take-up frame: WS300

WSTU-SC-20MWide-slot take-up · SC20 mmShaft diameter125910Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 31.2 mm
Drawing dimension B: 93.7 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 50.8 mm
Drawing dimension E: 60.5 mm
Take-up drawing F: 15.9 mm
Drawing dimension G: 9.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 50.8 mm
Drawing dimension K: 31.8 mm
Drawing dimension L: 28.4 mm
Take-up slot limits M: 75.82/76.58 mm
Drawing dimension N: 92.2 mm
Drawing dimension R: 12.7 mm
Drawing dimension S: 18.5 mm
Drawing dimension T: 35.1 mm
Assembly mass: 0.9 kg
Take-up frame: WS300

WSTU-SC-014Wide-slot take-up · SC7/8 inShaft diameter125356Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Drawing dimension B: 3.81 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.44 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.31 in
Drawing dimension L: 1.32 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension T: 1.38 in
Assembly mass: 2.2 lb
Take-up frame: WS300

WSTU-SC-015Wide-slot take-up · SC15/16 inShaft diameter125011Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Drawing dimension B: 3.81 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.44 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.31 in
Drawing dimension L: 1.32 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension T: 1.38 in
Assembly mass: 2.1 lb
Take-up frame: WS300

WSTU-SC-100Wide-slot take-up · SC1 inShaft diameter125012Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.34 in
Drawing dimension B: 3.81 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.00 in
Drawing dimension E: 2.44 in
Take-up drawing F: 5/8 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.00 in
Drawing dimension K: 1.31 in
Drawing dimension L: 1.32 in
Take-up slot limits M: 2.985/3.015 in
Drawing dimension N: 3.63 in
Drawing dimension R: 0.56 in
Drawing dimension S: 0.78 in
Drawing dimension T: 1.38 in
Assembly mass: 2.0 lb
Take-up frame: WS300

WSTU-SC-25MWide-slot take-up · SC25 mmShaft diameter125911Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 34.0 mm
Drawing dimension B: 96.8 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 50.8 mm
Drawing dimension E: 62.0 mm
Take-up drawing F: 15.9 mm
Drawing dimension G: 9.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 50.8 mm
Drawing dimension K: 33.3 mm
Drawing dimension L: 33.5 mm
Take-up slot limits M: 75.82/76.58 mm
Drawing dimension N: 92.2 mm
Drawing dimension R: 14.2 mm
Drawing dimension S: 19.8 mm
Drawing dimension T: 35.1 mm
Assembly mass: 1.0 kg
Take-up frame: WS300

WSTU-SC-101Wide-slot take-up · SC1-1/16 inShaft diameter125357Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Drawing dimension B: 4.38 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.25 in
Drawing dimension E: 2.75 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.19 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.57 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension T: 1.63 in
Assembly mass: 3.1 lb
Take-up frame: WS308

WSTU-SC-102Wide-slot take-up · SC1-1/8 inShaft diameter125358Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Drawing dimension B: 4.38 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.25 in
Drawing dimension E: 2.75 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.19 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.57 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension T: 1.63 in
Assembly mass: 3.0 lb
Take-up frame: WS308

WSTU-SC-103Wide-slot take-up · SC1-3/16 inShaft diameter125113Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Drawing dimension B: 4.38 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.25 in
Drawing dimension E: 2.75 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.19 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.57 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension T: 1.63 in
Assembly mass: 2.9 lb
Take-up frame: WS308

WSTU-SC-104SWide-slot take-up · SC1-1/4 inShaft diameter123175Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Drawing dimension B: 4.38 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.25 in
Drawing dimension E: 2.75 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.19 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.57 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension T: 1.63 in
Assembly mass: 2.8 lb
Take-up frame: WS308

WSTU-SC-30MWide-slot take-up · SC30 mmShaft diameter125912Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Drawing dimension B: 111.3 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 57.2 mm
Drawing dimension E: 69.9 mm
Take-up drawing F: 19.1 mm
Drawing dimension G: 9.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 55.6 mm
Drawing dimension K: 36.6 mm
Drawing dimension L: 39.9 mm
Take-up slot limits M: 88.39/89.15 mm
Drawing dimension N: 104.9 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension T: 41.3 mm
Assembly mass: 1.3 kg
Take-up frame: WS308

WSTU-SC-104Wide-slot take-up · SC1-1/4 inShaft diameter125360Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Drawing dimension B: 4.87 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.50 in
Drawing dimension E: 3.06 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.50 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.50 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.84 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension T: 1.63 in
Assembly mass: 3.8 lb
Take-up frame: WS308

Source: Dodge Mounted Ball Bearings, printed pages B1-62, B1-63, B1-66, B1-67 (PDF pages 73, 74, 77, 78). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SC-105Wide-slot take-up · SC1-5/16 inShaft diameter125359Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Drawing dimension B: 4.87 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.50 in
Drawing dimension E: 3.06 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.50 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.50 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.84 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension T: 1.63 in
Assembly mass: 3.7 lb
Take-up frame: WS308

WSTU-SC-106Wide-slot take-up · SC1-3/8 inShaft diameter125361Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Drawing dimension B: 4.87 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.50 in
Drawing dimension E: 3.06 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.50 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.50 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.84 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension T: 1.63 in
Assembly mass: 3.6 lb
Take-up frame: WS308

WSTU-SC-107Wide-slot take-up · SC1-7/16 inShaft diameter125114Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Drawing dimension B: 4.87 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.50 in
Drawing dimension E: 3.06 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.50 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.50 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.84 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension T: 1.63 in
Assembly mass: 3.5 lb
Take-up frame: WS308

WSTU-SC-35MWide-slot take-up · SC35 mmShaft diameter125913Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Drawing dimension B: 123.7 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 63.5 mm
Drawing dimension E: 77.7 mm
Take-up drawing F: 19.1 mm
Drawing dimension G: 12.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 63.5 mm
Drawing dimension K: 36.6 mm
Drawing dimension L: 46.7 mm
Take-up slot limits M: 88.39/89.15 mm
Drawing dimension N: 104.9 mm
Drawing dimension R: 17.0 mm
Drawing dimension S: 26.4 mm
Drawing dimension T: 41.3 mm
Assembly mass: 1.6 kg
Take-up frame: WS308

WSTU-SC-108Wide-slot take-up · SC1-1/2 inShaft diameter125120Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.69 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.50 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.05 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.50 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.1 lb
Take-up frame: WS400

WSTU-SC-110Wide-slot take-up · SC1-5/8 inShaft diameter125355Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.69 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.50 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.05 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.50 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.0 lb
Take-up frame: WS400

WSTU-SC-40MWide-slot take-up · SC40 mmShaft diameter125914Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 144.5 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 82.6 mm
Drawing dimension E: 88.9 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 52.1 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 114.3 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 2.8 kg
Take-up frame: WS400

WSTU-SC-110LWide-slot take-up · SC1-5/8 inShaft diameter125151Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.63 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.44 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.22 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.1 lb
Take-up frame: WS400

Source: Dodge Mounted Ball Bearings, printed pages B1-64, B1-65 (PDF pages 75, 76). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SC-111Wide-slot take-up · SC1-11/16 inShaft diameter125115Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.63 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.44 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.22 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.0 lb
Take-up frame: WS400

WSTU-SC-112Wide-slot take-up · SC1-3/4 inShaft diameter125362Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.63 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.44 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.22 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 5.9 lb
Take-up frame: WS400

WSTU-SC-113Wide-slot take-up · SC1-13/16 inShaft diameter125121Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.63 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.44 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.22 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 5.8 lb
Take-up frame: WS400

WSTU-SC-45MWide-slot take-up · SC45 mmShaft diameter125915Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 143.0 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 82.6 mm
Drawing dimension E: 87.4 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 56.4 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 120.7 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 2.7 kg
Take-up frame: WS400

WSTU-SC-115Wide-slot take-up · SC1-15/16 inShaft diameter125116Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.82 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.38 in
Drawing dimension E: 3.56 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.43 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.4 lb
Take-up frame: WS400

WSTU-SC-200Wide-slot take-up · SC2 inShaft diameter125363Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.82 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.38 in
Drawing dimension E: 3.56 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.43 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.2 lb
Take-up frame: WS400

WSTU-SC-50MWide-slot take-up · SC50 mmShaft diameter125916Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 147.8 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 85.9 mm
Drawing dimension E: 90.4 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 61.7 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 120.7 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 2.9 kg
Take-up frame: WS400

WSTU-SC-203Wide-slot take-up · SC2-3/16 inShaft diameter125117Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Drawing dimension B: 6.69 in
Drawing dimension C: 1.063 in
Drawing dimension D: 3.75 in
Drawing dimension E: 4.19 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.00 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.71 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension T: 2.50 in
Assembly mass: 10.0 lb
Take-up frame: WS502

WSTU-SC-204Wide-slot take-up · SC2-1/4 inShaft diameter125364Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Drawing dimension B: 6.69 in
Drawing dimension C: 1.063 in
Drawing dimension D: 3.75 in
Drawing dimension E: 4.19 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.00 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.71 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension T: 2.50 in
Assembly mass: 9.8 lb
Take-up frame: WS502

WSTU-SC-55MWide-slot take-up · SC55 mmShaft diameter125917Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Drawing dimension B: 169.9 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 95.3 mm
Drawing dimension E: 106.4 mm
Take-up drawing F: 31.8 mm
Drawing dimension G: 19.1 mm
Drawing dimension H: 25.4 mm
Drawing dimension J: 101.6 mm
Drawing dimension K: 63.5 mm
Drawing dimension L: 68.8 mm
Take-up slot limits M: 129.79/130.56 mm
Drawing dimension N: 149.4 mm
Drawing dimension R: 22.1 mm
Drawing dimension S: 34.3 mm
Drawing dimension T: 63.5 mm
Assembly mass: 4.5 kg
Take-up frame: WS502

WSTU-SCM-204Wide-slot take-up · SCM2-1/4 inShaft diameter135184Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Drawing dimension B: 7.50 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.00 in
Drawing dimension E: 4.69 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.97 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension T: 2.50 in
Assembly mass: 11.2 lb
Take-up frame: WS502

Source: Dodge Mounted Ball Bearings, printed pages B1-64, B1-65, B1-68, B1-69 (PDF pages 75, 76, 79, 80). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SC-207Wide-slot take-up · SC2-7/16 inShaft diameter125118Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Drawing dimension B: 7.50 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.00 in
Drawing dimension E: 4.69 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.97 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension T: 2.50 in
Assembly mass: 10.8 lb
Take-up frame: WS502

WSTU-SC-60MWide-slot take-up · SC60 mmShaft diameter125918Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Drawing dimension B: 190.5 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 101.6 mm
Drawing dimension E: 119.1 mm
Take-up drawing F: 31.8 mm
Drawing dimension G: 19.1 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 101.6 mm
Drawing dimension K: 63.5 mm
Drawing dimension L: 75.4 mm
Take-up slot limits M: 129.79/130.56 mm
Drawing dimension N: 149.4 mm
Drawing dimension R: 22.9 mm
Drawing dimension S: 35.8 mm
Drawing dimension T: 63.5 mm
Assembly mass: 4.9 kg
Take-up frame: WS502

WSTU-SCM-208Wide-slot take-up · SCM2-1/2 inShaft diameter135185Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Drawing dimension B: 8.56 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 5.38 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.31 in
Take-up slot limits M: 5.923/5.953 in
Drawing dimension N: 6.56 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension T: 2.75 in
Assembly mass: 18.0 lb
Take-up frame: WS515

WSTU-SC-211Wide-slot take-up · SC2-11/16 inShaft diameter064704Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Drawing dimension B: 8.56 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 5.38 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.31 in
Take-up slot limits M: 5.923/5.953 in
Drawing dimension N: 6.56 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension T: 2.75 in
Assembly mass: 17.8 lb
Take-up frame: WS515

WSTU-SC-70MWide-slot take-up · SC70 mmShaft diameter062975Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Drawing dimension B: 217.4 mm
Drawing dimension C: 27.0 mm
Drawing dimension D: 120.7 mm
Drawing dimension E: 136.7 mm
Take-up drawing F: 38.1 mm
Drawing dimension G: 20.6 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 111.3 mm
Drawing dimension K: 69.9 mm
Drawing dimension L: 84.1 mm
Take-up slot limits M: 150.44/151.21 mm
Drawing dimension N: 166.6 mm
Drawing dimension R: 26.9 mm
Drawing dimension S: 37.6 mm
Drawing dimension T: 69.9 mm
Assembly mass: 8.0 kg
Take-up frame: WS515

WSTU-SC-215Wide-slot take-up · SC2-15/16 inShaft diameter125119Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Drawing dimension B: 9.13 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 5.50 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.62 in
Take-up slot limits M: 5.923/5.953 in
Drawing dimension N: 6.69 in
Drawing dimension R: 0.86 in
Drawing dimension S: 1.47 in
Drawing dimension T: 2.75 in
Assembly mass: 18.9 lb
Take-up frame: WS515

WSTU-SC-75MWide-slot take-up · SC75 mmShaft diameter125919Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Drawing dimension B: 231.9 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 120.7 mm
Drawing dimension E: 139.7 mm
Take-up drawing F: 38.1 mm
Drawing dimension G: 20.6 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 111.3 mm
Drawing dimension K: 69.9 mm
Drawing dimension L: 91.9 mm
Take-up slot limits M: 150.44/151.21 mm
Drawing dimension N: 169.9 mm
Drawing dimension R: 21.8 mm
Drawing dimension S: 37.3 mm
Drawing dimension T: 69.9 mm
Assembly mass: 8.6 kg
Take-up frame: WS515

WSTU-SCM-100Wide-slot take-up · SCM1 inShaft diameter135117Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.52 in
Drawing dimension B: 4.38 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.25 in
Drawing dimension E: 2.75 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.38 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.19 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.57 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.58 in
Drawing dimension S: 0.94 in
Drawing dimension T: 1.63 in
Assembly mass: 2.9 lb
Take-up frame: WS308

Source: Dodge Mounted Ball Bearings, printed pages B1-66, B1-67 (PDF pages 77, 78). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SCM-25MWide-slot take-up · SCM25 mmShaft diameter125989Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 38.6 mm
Drawing dimension B: 111.3 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 57.2 mm
Drawing dimension E: 69.9 mm
Take-up drawing F: 19.1 mm
Drawing dimension G: 9.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 55.6 mm
Drawing dimension K: 36.6 mm
Drawing dimension L: 39.9 mm
Take-up slot limits M: 88.39/89.15 mm
Drawing dimension N: 104.9 mm
Drawing dimension R: 14.7 mm
Drawing dimension S: 23.9 mm
Drawing dimension T: 41.3 mm
Assembly mass: 1.4 kg
Take-up frame: WS308

WSTU-SCM-103Wide-slot take-up · SCM1-3/16 inShaft diameter135118Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.71 in
Drawing dimension B: 4.87 in
Drawing dimension C: 0.531 in
Drawing dimension D: 2.50 in
Drawing dimension E: 3.06 in
Take-up drawing F: 3/4 in
Drawing dimension G: 0.50 in
Drawing dimension H: 0.63 in
Drawing dimension J: 2.50 in
Drawing dimension K: 1.44 in
Drawing dimension L: 1.84 in
Take-up slot limits M: 3.480/3.510 in
Drawing dimension N: 4.13 in
Drawing dimension R: 0.67 in
Drawing dimension S: 1.04 in
Drawing dimension T: 1.63 in
Assembly mass: 3.9 lb
Take-up frame: WS308

WSTU-SCM-30MWide-slot take-up · SCM30 mmShaft diameter125990Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 43.4 mm
Drawing dimension B: 123.7 mm
Drawing dimension C: 13.49 mm
Drawing dimension D: 63.5 mm
Drawing dimension E: 77.7 mm
Take-up drawing F: 19.1 mm
Drawing dimension G: 12.7 mm
Drawing dimension H: 16.0 mm
Drawing dimension J: 63.5 mm
Drawing dimension K: 36.6 mm
Drawing dimension L: 46.7 mm
Take-up slot limits M: 88.39/89.15 mm
Drawing dimension N: 104.9 mm
Drawing dimension R: 17.0 mm
Drawing dimension S: 26.4 mm
Drawing dimension T: 41.3 mm
Assembly mass: 1.7 kg
Take-up frame: WS308

WSTU-SCM-107Wide-slot take-up · SCM1-7/16 inShaft diameter135116Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.69 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.50 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.05 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.50 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.1 lb
Take-up frame: WS400

WSTU-SCM-35MWide-slot take-up · SCM35 mmShaft diameter125991Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 144.5 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 82.6 mm
Drawing dimension E: 88.9 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 52.1 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 114.3 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 2.9 kg
Take-up frame: WS400

WSTU-SCM-108Wide-slot take-up · SCM1-1/2 inShaft diameter135120Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.63 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.25 in
Drawing dimension E: 3.44 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.22 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.0 lb
Take-up frame: WS400

WSTU-SCM-40MWide-slot take-up · SCM40 mmShaft diameter125992Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 143.0 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 82.6 mm
Drawing dimension E: 87.4 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 56.4 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 120.7 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 2.8 kg
Take-up frame: WS400

WSTU-SCM-111Wide-slot take-up · SCM1-11/16 inShaft diameter135121Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.82 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.38 in
Drawing dimension E: 3.56 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.43 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.4 lb
Take-up frame: WS400

WSTU-SCM-112Wide-slot take-up · SCM1-3/4 inShaft diameter135182Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 1.94 in
Drawing dimension B: 5.82 in
Drawing dimension C: 0.688 in
Drawing dimension D: 3.38 in
Drawing dimension E: 3.56 in
Take-up drawing F: 1 in
Drawing dimension G: 0.63 in
Drawing dimension H: 0.75 in
Drawing dimension J: 3.25 in
Drawing dimension K: 1.94 in
Drawing dimension L: 2.43 in
Take-up slot limits M: 3.985/4.015 in
Drawing dimension N: 4.75 in
Drawing dimension R: 0.75 in
Drawing dimension S: 1.19 in
Drawing dimension T: 1.94 in
Assembly mass: 6.4 lb
Take-up frame: WS400

WSTU-SCM-45MWide-slot take-up · SCM45 mmShaft diameter125993Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 49.3 mm
Drawing dimension B: 147.8 mm
Drawing dimension C: 17.48 mm
Drawing dimension D: 85.9 mm
Drawing dimension E: 90.4 mm
Take-up drawing F: 25.4 mm
Drawing dimension G: 16.0 mm
Drawing dimension H: 19.1 mm
Drawing dimension J: 82.6 mm
Drawing dimension K: 49.3 mm
Drawing dimension L: 61.7 mm
Take-up slot limits M: 101.22/101.98 mm
Drawing dimension N: 120.7 mm
Drawing dimension R: 19.1 mm
Drawing dimension S: 30.2 mm
Drawing dimension T: 49.3 mm
Assembly mass: 3.0 kg
Take-up frame: WS400

WSTU-SCM-115Wide-slot take-up · SCM1-15/16 inShaft diameter135123Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.22 in
Drawing dimension B: 6.69 in
Drawing dimension C: 1.063 in
Drawing dimension D: 3.75 in
Drawing dimension E: 4.19 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.00 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.71 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.87 in
Drawing dimension S: 1.35 in
Drawing dimension T: 2.50 in
Assembly mass: 10.1 lb
Take-up frame: WS502

Source: Dodge Mounted Ball Bearings, printed pages B1-68, B1-69 (PDF pages 79, 80). Checked 2026-10-04. Standard assembly shown; do not transfer these values to a different suffix or unlisted variant.

WSTU-SCM-50MWide-slot take-up · SCM50 mmShaft diameter125994Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 56.4 mm
Drawing dimension B: 169.9 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 95.3 mm
Drawing dimension E: 106.4 mm
Take-up drawing F: 31.8 mm
Drawing dimension G: 19.1 mm
Drawing dimension H: 25.4 mm
Drawing dimension J: 101.6 mm
Drawing dimension K: 63.5 mm
Drawing dimension L: 68.8 mm
Take-up slot limits M: 129.79/130.56 mm
Drawing dimension N: 149.4 mm
Drawing dimension R: 22.1 mm
Drawing dimension S: 34.3 mm
Drawing dimension T: 63.5 mm
Assembly mass: 4.7 kg
Take-up frame: WS502

WSTU-SCM-203Wide-slot take-up · SCM2-3/16 inShaft diameter135125Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.31 in
Drawing dimension B: 7.50 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.00 in
Drawing dimension E: 4.69 in
Take-up drawing F: 1-1/4 in
Drawing dimension G: 0.75 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.00 in
Drawing dimension K: 2.50 in
Drawing dimension L: 2.97 in
Take-up slot limits M: 5.110/5.140 in
Drawing dimension N: 5.88 in
Drawing dimension R: 0.90 in
Drawing dimension S: 1.41 in
Drawing dimension T: 2.50 in
Assembly mass: 11.4 lb
Take-up frame: WS502

WSTU-SCM-55MWide-slot take-up · SCM55 mmShaft diameter125995Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 58.7 mm
Drawing dimension B: 190.5 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 101.6 mm
Drawing dimension E: 119.1 mm
Take-up drawing F: 31.8 mm
Drawing dimension G: 19.1 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 101.6 mm
Drawing dimension K: 63.5 mm
Drawing dimension L: 75.4 mm
Take-up slot limits M: 129.79/130.56 mm
Drawing dimension N: 149.4 mm
Drawing dimension R: 22.9 mm
Drawing dimension S: 35.8 mm
Drawing dimension T: 63.5 mm
Assembly mass: 5.1 kg
Take-up frame: WS502

WSTU-SCM-207Wide-slot take-up · SCM2-7/16 inShaft diameter135127Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.54 in
Drawing dimension B: 8.56 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 5.38 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.31 in
Take-up slot limits M: 5.923/5.953 in
Drawing dimension N: 6.56 in
Drawing dimension R: 1.06 in
Drawing dimension S: 1.48 in
Drawing dimension T: 2.75 in
Assembly mass: 18.2 lb
Take-up frame: WS515

WSTU-SCM-65MWide-slot take-up · SCM65 mmShaft diameter125996Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 64.5 mm
Drawing dimension B: 217.4 mm
Drawing dimension C: 27.0 mm
Drawing dimension D: 120.7 mm
Drawing dimension E: 136.7 mm
Take-up drawing F: 38.1 mm
Drawing dimension G: 20.6 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 111.3 mm
Drawing dimension K: 69.9 mm
Drawing dimension L: 84.1 mm
Take-up slot limits M: 150.44/151.21 mm
Drawing dimension N: 166.6 mm
Drawing dimension R: 26.9 mm
Drawing dimension S: 37.6 mm
Drawing dimension T: 69.9 mm
Assembly mass: 8.1 kg
Take-up frame: WS515

WSTU-SCM-211Wide-slot take-up · SCM2-11/16 inShaft diameter135129Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.33 in
Drawing dimension B: 9.13 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 5.50 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.62 in
Take-up slot limits M: 5.923/5.953 in
Drawing dimension N: 6.69 in
Drawing dimension R: 0.86 in
Drawing dimension S: 1.47 in
Drawing dimension T: 2.75 in
Assembly mass: 19.0 lb
Take-up frame: WS515

WSTU-SCM-70MWide-slot take-up · SCM70 mmShaft diameter125997Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 59.2 mm
Drawing dimension B: 231.9 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 120.7 mm
Drawing dimension E: 139.7 mm
Take-up drawing F: 38.1 mm
Drawing dimension G: 20.6 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 111.3 mm
Drawing dimension K: 69.9 mm
Drawing dimension L: 91.9 mm
Take-up slot limits M: 150.44/151.21 mm
Drawing dimension N: 169.9 mm
Drawing dimension R: 21.8 mm
Drawing dimension S: 37.3 mm
Drawing dimension T: 69.9 mm
Assembly mass: 8.9 kg
Take-up frame: WS515

WSTU-SCM-215Wide-slot take-up · SCM2-15/16 inShaft diameter135130Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Drawing dimension B: 9.13 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 2.38 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.83 in
Take-up slot limits M: 6.485/6.515 in
Drawing dimension N: 7.25 in
Drawing dimension R: 0.88 in
Drawing dimension S: 1.50 in
Drawing dimension T: 2.75 in
Assembly mass: 21.7 lb
Take-up frame: WS608

WSTU-SCM-300Wide-slot take-up · SCM3 inShaft diameter135181Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in in

Inner-ring width A: 2.38 in
Drawing dimension B: 9.13 in
Drawing dimension C: 1.063 in
Drawing dimension D: 4.75 in
Drawing dimension E: 2.38 in
Take-up drawing F: 1-1/2 in
Drawing dimension G: 0.81 in
Drawing dimension H: 1.25 in
Drawing dimension J: 4.38 in
Drawing dimension K: 2.75 in
Drawing dimension L: 3.83 in
Take-up slot limits M: 6.485/6.515 in
Drawing dimension N: 7.25 in
Drawing dimension R: 0.88 in
Drawing dimension S: 1.50 in
Drawing dimension T: 2.75 in
Assembly mass: 21.5 lb
Take-up frame: WS608

WSTU-SCM-75MWide-slot take-up · SCM75 mmShaft diameter125998Catalogue part numberDetails

Complete assembly · Set-screw locking · Dimensions in mm

Inner-ring width A: 60.5 mm
Drawing dimension B: 231.6 mm
Drawing dimension C: 27.00 mm
Drawing dimension D: 120.7 mm
Drawing dimension E: 60.5 mm
Take-up drawing F: 38.1 mm
Drawing dimension G: 20.6 mm
Drawing dimension H: 31.8 mm
Drawing dimension J: 111.3 mm
Drawing dimension K: 69.9 mm
Drawing dimension L: 97.3 mm
Take-up slot limits M: 164.72/165.48 mm
Drawing dimension N: 184.2 mm
Drawing dimension R: 22.4 mm
Drawing dimension S: 38.1 mm
Drawing dimension T: 69.9 mm
Assembly mass: 9.5 kg
Take-up frame: WS608

Structure · function · identification

What is this bearing type?

A mounted bearing unit combines a bearing insert with a supporting housing and sealing arrangement. A pillow block, flange unit and take-up unit can use similar inserts while having entirely different mounting geometry.

Part or design	What it does	What to verify
Insert	Supports the shaft and includes the specified locking and sealing features.	A replacement insert is not a complete unit.
Housing	Provides a foot, flange or other mounting arrangement.	Check bolt pattern, shaft centre height and available space.
Shaft locking	May use set screws, an eccentric collar, an adapter or another design.	Preserve the locking method and shaft requirements.

On a small screen, scroll the table horizontally to read all three columns.

Variants that change the answer

Two-bolt and four-bolt flanges differ from foot-mounted units. Outer-ring profile and the insert/housing combination also matter; matching the bore is only the first check.

What the family name cannot tell you

Housing length is not bearing outside diameter. A unit drawing may use L, H or mounting-hole dimensions that cannot be compared directly with a bare bearing’s d×D×B.

Identify the exact part before comparing

Record the complete unit marking as well as the insert marking.
Compare shaft size, housing shape, mounting holes and centre height.
Check locking, relubrication access and sealing before shortlisting an alternative.

Inspect real catalogue records below →Insert-only records →Separate housings →Unit drawing lookup →

Technical reference basis: NSK: Ball Bearing Units. Explanation and lookup workflow: BearingScope. Manufacturer-specific limits remain attached to the exact product record.

Pillow bearing, pillow block and mounted bearing: what do the names mean?

Pillow bearing and bearing pillow block are common search variations for a bearing carried in a foot-mounted housing. The complete mounted unit includes the bearing and supporting housing; a housing-only result is not a complete unit.

NSK uses pillow block and plummer block terminology for its ball-bearing units. Other catalogues use plummer block for separately assembled housings. Keep the manufacturer's full designation and assembly scope visible instead of assuming the words always identify the same construction.

Reference basis: NSK Ball Bearing Units; BearingScope component-identification workflow. Explanation and comparison workflow: BearingScope.

Pillow block vs flange vs take-up unit

NSK lists cast iron, ductile iron, steel and stainless housing choices in its unit range. Material is a separate selection field: a cast-iron pillow block and a stainless unit should not be treated as equivalent from bore size alone.

On a small screen, scroll the table sideways to read every column.

Shape	How to recognise the mounting	Record for comparison
Pillow block	Foot/base mounting	Shaft centre height, foot dimensions and bolt spacing
Square flange	Four-bolt flange	Flange outline, bolt pattern and mounting-face position
Oval / diamond flange	Two-bolt flange	Hole spacing and available mounting envelope
Take-up unit	Housing intended for adjustment in its support	Guide arrangement, travel and matching frame
Cartridge or hanger unit	Different supporting arrangement	The actual drawing, not a borrowed pillow-block dimension

Reference basis: NSK Ball Bearing Units and NSK Self-Lube Mounted Units. Explanation and comparison workflow: BearingScope.

1 inch is 25.4 mm, not 25 mm

Enter the original shaft units before choosing a candidate. The exact conversion is 1 inch = 25.4 mm. A 25 mm shaft and a 1 inch shaft differ by 0.4 mm; that difference is not a suffix formatting choice.

The table below separates metric and inch catalogue examples. Use the full designation rather than deleting an inch suffix to obtain more search results. All housing dimensions remain in millimetres even when the shaft bore is specified in inches.

Can I search a fraction such as 3/4 or 1 1/2?

Yes. Select Inches / fractions, enter the original fraction, and the table filters immediately. The filter converts the input; it does not create an unlisted manufacturer model.

Does a shared housing prove the same shaft bore?

No. Compare the complete unit and insert designation. A housing can appear in more than one catalogue assembly; the bore must be verified for the actual insert.

Why did my shaft-size search return no examples?

This is a selected reference table, not an exhaustive catalogue. An empty result is a remaining data gap, not evidence that no such bearing unit exists.

Reference basis: Exact inch-to-millimetre conversion; SKF UC catalogue examples below. Explanation and comparison workflow: BearingScope.

Which dimensions belong in a pillow-block size chart?

For a complete replacement comparison, also retain foot width, hole/slot geometry, fastener requirements, seal arrangement, locking method and available clearance. This table is a dimensional starting point, not a declaration that the mounting or load capacity is interchangeable.

On a small screen, scroll the table sideways to read every column.

Dimension	Meaning in this reference	Do not substitute
d	Shaft bore	Housing seat diameter
H1	Shaft centre height in this catalogue	Overall height H
H	Overall height in this catalogue	Shaft centre height H1
L	Overall housing length	Insert bearing outside diameter
J	Mounting-bolt centre distance	Hole diameter or slot length

Reference basis: SKF UC dimensional drawings; BearingScope comparison record. Explanation and comparison workflow: BearingScope.

UCP vs UCF vs UCFL vs UCFC: what changes?

In the SKF UC-range reference used here, these prefixes identify different complete-unit housings. A shared insert size does not make their mounting interfaces interchangeable. Keep the full unit designation rather than searching only the final three digits.

On a small screen, scroll the table sideways to read every column.

Unit family	Mounting structure in this reference	Critical comparison
UCP	Foot-mounted pillow block	Shaft centre height H1 and mounting-bolt distance J
UCF	Square four-bolt flange	Square flange side L and bolt spacing J
UCFL	Oval two-bolt flange	Overall envelope H × L and bolt spacing J
UCFC	Round four-bolt flange with a register	Overall diameter L, bolt-circle J, adjacent-hole spacing J1 and register Da

Reference basis: SKF UC range publication 17273, dimensional tables and drawings on pages 8–19. Explanation and comparison workflow: BearingScope.

Inch suffixes, rounded millimetres and missing sizes

The expanded table includes the 41 UCP entries printed in the selected metric and inch sections. It is a source-edition reference, not a claim that every current SKF product or every manufacturer's UCP size is listed.

For example, 15/16 inch converts exactly to 23.8125 mm, while this catalogue prints 23.813 mm. The shaft filter accepts the exact fraction and its published rounded metric value. The displayed values remain as published; rounding does not alter shaft tolerances.

A size absent from these tables remains unresolved. Do not invent a UCP202, UCP203 or an unlisted inch suffix by extending the numbering pattern. Housing and insert conflicts found in the source are flagged rather than silently corrected.

Reference basis: SKF UC range publication 17273, pages 8–11; exact inch conversion. Explanation and comparison workflow: BearingScope.

From shaft bore to a complete pillow block: compare the right dimensions

A shaft-size request needs a complete unit example, not just a housing number. The additional FAG table below includes the bore, bolt spacing, shaft-centre height, insert designation and housing designation from the same model record.

For example, FAG UELP206 is a 30 mm-bore long-base unit. Its source labels the shaft-centre distance H = 42.9 mm and overall height H2 = 83 mm. Do not compare that H blindly with the SKF UC table: SKF uses H1 for the shaft centre and H for overall height in that publication.

Type a complete unit marking, an insert marking or a housing marking in the reference filter. A component match helps identify the assembly record; it does not establish that the component can replace another brand’s part.

On a small screen, scroll the table sideways to read every column.

Comparison item	Meaning	What the lookup does not prove
Shaft bore d	Diameter of the shaft passing through the insert	Match the stated unit and precision; do not use a housing envelope as the bore.
Mounting span J	Distance between fixing-hole centres in the named drawing	Compare both hole spacing and hole or slot dimensions.
Shaft centre / flange projection	The shaft location or axial position relative to the mounting surface	Use the definition beside the value, not the letter alone.
Housing and insert markings	Separate component identifiers within a complete unit	A housing marking alone is not the full bearing assembly designation.
Basic load rating	A rating of the bearing record	It is not the permissible load of the housing, bolts or the complete machine.

Reference basis: Schaeffler medias FAG UELP, UELF and UELFL individual product records; SKF UC range publication 17273. Symbols are manufacturer- and drawing-specific. Explanation and comparison workflow: BearingScope.

Complete unit · shaft bore · mounting dimensions

Timken pillow blocks and take-up units: shaft sizes and dimensions

Start with the shaft diameter, then compare the complete unit designation and mounting geometry. These documented Timken U-series examples have cast-iron housings and UC set-screw locking inserts. They are reference candidates, not a statement of stock, equipment fitment or approved interchangeability.

Inches are not millimetres. A 1-inch shaft is 25.4 mm, not 25 mm. Enter fractions as 1/2, 3/4 or 1 1/4 and select Inches. If an old note says “1 1 2”, confirm that it means 1½ inches before choosing a unit. Missing units and fraction marks cannot establish a fit.

Complete unit or insert Shaft diameter d Input units Mounting structure

102 documented units. Filters update immediately.

TIMKEN · Pillow block

UCP201

Shaft d: 12 mm

UC insert: UC201

Shaft centre height H: 30.2 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 30.2 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 60 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.6 kg

The catalogue combines this unit with other bore variants in a shared specification block. Housing dimensions, load ratings and mass above reproduce that block; mass is not an independently verified weight for each variant. Cr and C0r are basic ratings, not permissible machine loads. A bolt-size entry is not a tightening torque.

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 16. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP201-8

Shaft d: 1/2 in (12.7 mm, calculated)

UC insert: UC201-8

Shaft centre height H: 30.2 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 30.2 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 60 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP202

Shaft d: 15 mm

UC insert: UC202

Shaft centre height H: 30.2 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 30.2 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 60 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP202-10

Shaft d: 5/8 in (15.875 mm, calculated)

UC insert: UC202-10

Shaft centre height H: 30.2 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 30.2 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 60 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP203

Shaft d: 17 mm

UC insert: UC203

Shaft centre height H: 30.2 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 30.2 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 60 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP204-12

Shaft d: 3/4 in (19.05 mm, calculated)

UC insert: UC204-12

Shaft centre height H: 33.3 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 33.3 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 65 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.7 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP204

Shaft d: 20 mm

UC insert: UC204

Shaft centre height H: 33.3 mm
Mounting-bolt centre distance J: 95 mm
Housing length L: 127 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Shaft centre height H: 33.3 mm
Housing length L: 127 mm
Source outline dimension L1: 36 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 95 mm
Overall height H2: 65 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.7 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP205-14

Shaft d: 7/8 in (22.225 mm, calculated)

UC insert: UC205-14

Shaft centre height H: 36.5 mm
Mounting-bolt centre distance J: 105 mm
Housing length L: 140 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Shaft centre height H: 36.5 mm
Housing length L: 140 mm
Source outline dimension L1: 38 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 105 mm
Overall height H2: 70 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP205-15

Shaft d: 15/16 in (23.8125 mm, calculated)

UC insert: UC205-15

Shaft centre height H: 36.5 mm
Mounting-bolt centre distance J: 105 mm
Housing length L: 140 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Shaft centre height H: 36.5 mm
Housing length L: 140 mm
Source outline dimension L1: 38 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 105 mm
Overall height H2: 70 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP205

Shaft d: 25 mm

UC insert: UC205

Shaft centre height H: 36.5 mm
Mounting-bolt centre distance J: 105 mm
Housing length L: 140 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Shaft centre height H: 36.5 mm
Housing length L: 140 mm
Source outline dimension L1: 38 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 105 mm
Overall height H2: 70 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP205-16

Shaft d: 1 in (25.4 mm, calculated)

UC insert: UC205-16

Shaft centre height H: 36.5 mm
Mounting-bolt centre distance J: 105 mm
Housing length L: 140 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Shaft centre height H: 36.5 mm
Housing length L: 140 mm
Source outline dimension L1: 38 mm
Housing width A: 38 mm
Foot thickness H1: 16 mm
Mounting-bolt centre distance J: 105 mm
Overall height H2: 70 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Mounting slot width N: 13 mm
Mounting slot length N1: 18 mm
Catalogue mounting bolt: M10
Shared catalogue mass: 0.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP206-18

Shaft d: 1 1/8 in (28.575 mm, calculated)

UC insert: UC206-18

Shaft centre height H: 42.9 mm
Mounting-bolt centre distance J: 121 mm
Housing length L: 165 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Shaft centre height H: 42.9 mm
Housing length L: 165 mm
Source outline dimension L1: 48 mm
Housing width A: 48 mm
Foot thickness H1: 17 mm
Mounting-bolt centre distance J: 121 mm
Overall height H2: 84 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.3 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP206

Shaft d: 30 mm

UC insert: UC206

Shaft centre height H: 42.9 mm
Mounting-bolt centre distance J: 121 mm
Housing length L: 165 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Shaft centre height H: 42.9 mm
Housing length L: 165 mm
Source outline dimension L1: 48 mm
Housing width A: 48 mm
Foot thickness H1: 17 mm
Mounting-bolt centre distance J: 121 mm
Overall height H2: 84 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.3 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP206-19

Shaft d: 1 3/16 in (30.1625 mm, calculated)

UC insert: UC206-19

Shaft centre height H: 42.9 mm
Mounting-bolt centre distance J: 121 mm
Housing length L: 165 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Shaft centre height H: 42.9 mm
Housing length L: 165 mm
Source outline dimension L1: 48 mm
Housing width A: 48 mm
Foot thickness H1: 17 mm
Mounting-bolt centre distance J: 121 mm
Overall height H2: 84 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.3 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP206-20

Shaft d: 1 1/4 in (31.75 mm, calculated)

UC insert: UC206-20

Shaft centre height H: 42.9 mm
Mounting-bolt centre distance J: 121 mm
Housing length L: 165 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Shaft centre height H: 42.9 mm
Housing length L: 165 mm
Source outline dimension L1: 48 mm
Housing width A: 48 mm
Foot thickness H1: 17 mm
Mounting-bolt centre distance J: 121 mm
Overall height H2: 84 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.3 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP207-20

Shaft d: 1 1/4 in (31.75 mm, calculated)

UC insert: UC207-20

Shaft centre height H: 47.6 mm
Mounting-bolt centre distance J: 127 mm
Housing length L: 167 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Shaft centre height H: 47.6 mm
Housing length L: 167 mm
Source outline dimension L1: 47 mm
Housing width A: 48 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 127 mm
Overall height H2: 95 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP207-21

Shaft d: 1 5/16 in (33.3375 mm, calculated)

UC insert: UC207-21

Shaft centre height H: 47.6 mm
Mounting-bolt centre distance J: 127 mm
Housing length L: 167 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Shaft centre height H: 47.6 mm
Housing length L: 167 mm
Source outline dimension L1: 47 mm
Housing width A: 48 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 127 mm
Overall height H2: 95 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP207-22

Shaft d: 1 3/8 in (34.925 mm, calculated)

UC insert: UC207-22

Shaft centre height H: 47.6 mm
Mounting-bolt centre distance J: 127 mm
Housing length L: 167 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Shaft centre height H: 47.6 mm
Housing length L: 167 mm
Source outline dimension L1: 47 mm
Housing width A: 48 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 127 mm
Overall height H2: 95 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP207

Shaft d: 35 mm

UC insert: UC207

Shaft centre height H: 47.6 mm
Mounting-bolt centre distance J: 127 mm
Housing length L: 167 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Shaft centre height H: 47.6 mm
Housing length L: 167 mm
Source outline dimension L1: 47 mm
Housing width A: 48 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 127 mm
Overall height H2: 95 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP207-23

Shaft d: 1 7/16 in (36.5125 mm, calculated)

UC insert: UC207-23

Shaft centre height H: 47.6 mm
Mounting-bolt centre distance J: 127 mm
Housing length L: 167 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Shaft centre height H: 47.6 mm
Housing length L: 167 mm
Source outline dimension L1: 47 mm
Housing width A: 48 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 127 mm
Overall height H2: 95 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 1.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP208-24

Shaft d: 1 1/2 in (38.1 mm, calculated)

UC insert: UC208-24

Shaft centre height H: 49.2 mm
Mounting-bolt centre distance J: 137 mm
Housing length L: 184 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Shaft centre height H: 49.2 mm
Housing length L: 184 mm
Source outline dimension L1: 53 mm
Housing width A: 54 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 137 mm
Overall height H2: 98 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.0 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP208-25

Shaft d: 1 9/16 in (39.6875 mm, calculated)

UC insert: UC208-25

Shaft centre height H: 49.2 mm
Mounting-bolt centre distance J: 137 mm
Housing length L: 184 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Shaft centre height H: 49.2 mm
Housing length L: 184 mm
Source outline dimension L1: 53 mm
Housing width A: 54 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 137 mm
Overall height H2: 98 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.0 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP208

Shaft d: 40 mm

UC insert: UC208

Shaft centre height H: 49.2 mm
Mounting-bolt centre distance J: 137 mm
Housing length L: 184 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Shaft centre height H: 49.2 mm
Housing length L: 184 mm
Source outline dimension L1: 53 mm
Housing width A: 54 mm
Foot thickness H1: 18 mm
Mounting-bolt centre distance J: 137 mm
Overall height H2: 98 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.0 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP209-26

Shaft d: 1 5/8 in (41.275 mm, calculated)

UC insert: UC209-26

Shaft centre height H: 54.0 mm
Mounting-bolt centre distance J: 146 mm
Housing length L: 190 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Shaft centre height H: 54.0 mm
Housing length L: 190 mm
Source outline dimension L1: 55 mm
Housing width A: 54 mm
Foot thickness H1: 20 mm
Mounting-bolt centre distance J: 146 mm
Overall height H2: 106 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.2 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP209-27

Shaft d: 1 11/16 in (42.8625 mm, calculated)

UC insert: UC209-27

Shaft centre height H: 54.0 mm
Mounting-bolt centre distance J: 146 mm
Housing length L: 190 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Shaft centre height H: 54.0 mm
Housing length L: 190 mm
Source outline dimension L1: 55 mm
Housing width A: 54 mm
Foot thickness H1: 20 mm
Mounting-bolt centre distance J: 146 mm
Overall height H2: 106 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.2 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP209-28

Shaft d: 1 3/4 in (44.45 mm, calculated)

UC insert: UC209-28

Shaft centre height H: 54.0 mm
Mounting-bolt centre distance J: 146 mm
Housing length L: 190 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Shaft centre height H: 54.0 mm
Housing length L: 190 mm
Source outline dimension L1: 55 mm
Housing width A: 54 mm
Foot thickness H1: 20 mm
Mounting-bolt centre distance J: 146 mm
Overall height H2: 106 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.2 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP209

Shaft d: 45 mm

UC insert: UC209

Shaft centre height H: 54.0 mm
Mounting-bolt centre distance J: 146 mm
Housing length L: 190 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Shaft centre height H: 54.0 mm
Housing length L: 190 mm
Source outline dimension L1: 55 mm
Housing width A: 54 mm
Foot thickness H1: 20 mm
Mounting-bolt centre distance J: 146 mm
Overall height H2: 106 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Mounting slot width N: 17 mm
Mounting slot length N1: 21 mm
Catalogue mounting bolt: M14
Shared catalogue mass: 2.2 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP210-30

Shaft d: 1 7/8 in (47.625 mm, calculated)

UC insert: UC210-30

Shaft centre height H: 57.2 mm
Mounting-bolt centre distance J: 159 mm
Housing length L: 206 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Shaft centre height H: 57.2 mm
Housing length L: 206 mm
Source outline dimension L1: 60 mm
Housing width A: 60 mm
Foot thickness H1: 21 mm
Mounting-bolt centre distance J: 159 mm
Overall height H2: 113 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 2.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 17. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP210-31

Shaft d: 1 15/16 in (49.2125 mm, calculated)

UC insert: UC210-31

Shaft centre height H: 57.2 mm
Mounting-bolt centre distance J: 159 mm
Housing length L: 206 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Shaft centre height H: 57.2 mm
Housing length L: 206 mm
Source outline dimension L1: 60 mm
Housing width A: 60 mm
Foot thickness H1: 21 mm
Mounting-bolt centre distance J: 159 mm
Overall height H2: 113 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 2.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP210

Shaft d: 50 mm

UC insert: UC210

Shaft centre height H: 57.2 mm
Mounting-bolt centre distance J: 159 mm
Housing length L: 206 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Shaft centre height H: 57.2 mm
Housing length L: 206 mm
Source outline dimension L1: 60 mm
Housing width A: 60 mm
Foot thickness H1: 21 mm
Mounting-bolt centre distance J: 159 mm
Overall height H2: 113 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 2.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP210-32

Shaft d: 2 in (50.8 mm, calculated)

UC insert: UC210-32

Shaft centre height H: 57.2 mm
Mounting-bolt centre distance J: 159 mm
Housing length L: 206 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Shaft centre height H: 57.2 mm
Housing length L: 206 mm
Source outline dimension L1: 60 mm
Housing width A: 60 mm
Foot thickness H1: 21 mm
Mounting-bolt centre distance J: 159 mm
Overall height H2: 113 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 2.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP211-32

Shaft d: 2 in (50.8 mm, calculated)

UC insert: UC211-32

Shaft centre height H: 63.5 mm
Mounting-bolt centre distance J: 171 mm
Housing length L: 219 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Shaft centre height H: 63.5 mm
Housing length L: 219 mm
Source outline dimension L1: 65 mm
Housing width A: 60 mm
Foot thickness H1: 23 mm
Mounting-bolt centre distance J: 171 mm
Overall height H2: 125 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 3.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP211-34

Shaft d: 2 1/8 in (53.975 mm, calculated)

UC insert: UC211-34

Shaft centre height H: 63.5 mm
Mounting-bolt centre distance J: 171 mm
Housing length L: 219 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Shaft centre height H: 63.5 mm
Housing length L: 219 mm
Source outline dimension L1: 65 mm
Housing width A: 60 mm
Foot thickness H1: 23 mm
Mounting-bolt centre distance J: 171 mm
Overall height H2: 125 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 3.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP211

Shaft d: 55 mm

UC insert: UC211

Shaft centre height H: 63.5 mm
Mounting-bolt centre distance J: 171 mm
Housing length L: 219 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Shaft centre height H: 63.5 mm
Housing length L: 219 mm
Source outline dimension L1: 65 mm
Housing width A: 60 mm
Foot thickness H1: 23 mm
Mounting-bolt centre distance J: 171 mm
Overall height H2: 125 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 3.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP211-35

Shaft d: 2 3/16 in (55.5625 mm, calculated)

UC insert: UC211-35

Shaft centre height H: 63.5 mm
Mounting-bolt centre distance J: 171 mm
Housing length L: 219 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Shaft centre height H: 63.5 mm
Housing length L: 219 mm
Source outline dimension L1: 65 mm
Housing width A: 60 mm
Foot thickness H1: 23 mm
Mounting-bolt centre distance J: 171 mm
Overall height H2: 125 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 22 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 3.6 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP212-36

Shaft d: 2 1/4 in (57.15 mm, calculated)

UC insert: UC212-36

Shaft centre height H: 69.8 mm
Mounting-bolt centre distance J: 184 mm
Housing length L: 241 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Shaft centre height H: 69.8 mm
Housing length L: 241 mm
Source outline dimension L1: 73 mm
Housing width A: 70 mm
Foot thickness H1: 25 mm
Mounting-bolt centre distance J: 184 mm
Overall height H2: 138 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 25 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 4.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP212

Shaft d: 60 mm

UC insert: UC212

Shaft centre height H: 69.8 mm
Mounting-bolt centre distance J: 184 mm
Housing length L: 241 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Shaft centre height H: 69.8 mm
Housing length L: 241 mm
Source outline dimension L1: 73 mm
Housing width A: 70 mm
Foot thickness H1: 25 mm
Mounting-bolt centre distance J: 184 mm
Overall height H2: 138 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 25 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 4.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP212-38

Shaft d: 2 3/8 in (60.325 mm, calculated)

UC insert: UC212-38

Shaft centre height H: 69.8 mm
Mounting-bolt centre distance J: 184 mm
Housing length L: 241 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Shaft centre height H: 69.8 mm
Housing length L: 241 mm
Source outline dimension L1: 73 mm
Housing width A: 70 mm
Foot thickness H1: 25 mm
Mounting-bolt centre distance J: 184 mm
Overall height H2: 138 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 25 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 4.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP212-39

Shaft d: 2 7/16 in (61.9125 mm, calculated)

UC insert: UC212-39

Shaft centre height H: 69.8 mm
Mounting-bolt centre distance J: 184 mm
Housing length L: 241 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Shaft centre height H: 69.8 mm
Housing length L: 241 mm
Source outline dimension L1: 73 mm
Housing width A: 70 mm
Foot thickness H1: 25 mm
Mounting-bolt centre distance J: 184 mm
Overall height H2: 138 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 20 mm
Mounting slot length N1: 25 mm
Catalogue mounting bolt: M16
Shared catalogue mass: 4.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP213-40

Shaft d: 2 1/2 in (63.5 mm, calculated)

UC insert: UC213-40

Shaft centre height H: 76.2 mm
Mounting-bolt centre distance J: 203 mm
Housing length L: 265 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN
Shaft centre height H: 76.2 mm
Housing length L: 265 mm
Source outline dimension L1: 78 mm
Housing width A: 70 mm
Foot thickness H1: 27 mm
Mounting-bolt centre distance J: 203 mm
Overall height H2: 150 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 5.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP213

Shaft d: 65 mm

UC insert: UC213

Shaft centre height H: 76.2 mm
Mounting-bolt centre distance J: 203 mm
Housing length L: 265 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN
Shaft centre height H: 76.2 mm
Housing length L: 265 mm
Source outline dimension L1: 78 mm
Housing width A: 70 mm
Foot thickness H1: 27 mm
Mounting-bolt centre distance J: 203 mm
Overall height H2: 150 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 5.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP214-44

Shaft d: 2 3/4 in (69.85 mm, calculated)

UC insert: UC214-44

Shaft centre height H: 79.4 mm
Mounting-bolt centre distance J: 210 mm
Housing length L: 266 mm
Insert inner-ring width B: 74.6 mm
Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN
Shaft centre height H: 79.4 mm
Housing length L: 266 mm
Source outline dimension L1: 75 mm
Housing width A: 72 mm
Foot thickness H1: 27 mm
Mounting-bolt centre distance J: 210 mm
Overall height H2: 157 mm
Insert centre-to-face S: 30.2 mm
Insert inner-ring width B: 74.6 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 6.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP214

Shaft d: 70 mm

UC insert: UC214

Shaft centre height H: 79.4 mm
Mounting-bolt centre distance J: 210 mm
Housing length L: 266 mm
Insert inner-ring width B: 74.6 mm
Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN
Shaft centre height H: 79.4 mm
Housing length L: 266 mm
Source outline dimension L1: 75 mm
Housing width A: 72 mm
Foot thickness H1: 27 mm
Mounting-bolt centre distance J: 210 mm
Overall height H2: 157 mm
Insert centre-to-face S: 30.2 mm
Insert inner-ring width B: 74.6 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 6.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP215-47

Shaft d: 2 15/16 in (74.6125 mm, calculated)

UC insert: UC215-47

Shaft centre height H: 82.6 mm
Mounting-bolt centre distance J: 217 mm
Housing length L: 275 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Shaft centre height H: 82.6 mm
Housing length L: 275 mm
Source outline dimension L1: 78 mm
Housing width A: 74 mm
Foot thickness H1: 28 mm
Mounting-bolt centre distance J: 217 mm
Overall height H2: 162 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 7.4 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP215

Shaft d: 75 mm

UC insert: UC215

Shaft centre height H: 82.6 mm
Mounting-bolt centre distance J: 217 mm
Housing length L: 275 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Shaft centre height H: 82.6 mm
Housing length L: 275 mm
Source outline dimension L1: 78 mm
Housing width A: 74 mm
Foot thickness H1: 28 mm
Mounting-bolt centre distance J: 217 mm
Overall height H2: 162 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 7.4 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP215-48

Shaft d: 3 in (76.2 mm, calculated)

UC insert: UC215-48

Shaft centre height H: 82.6 mm
Mounting-bolt centre distance J: 217 mm
Housing length L: 275 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Shaft centre height H: 82.6 mm
Housing length L: 275 mm
Source outline dimension L1: 78 mm
Housing width A: 74 mm
Foot thickness H1: 28 mm
Mounting-bolt centre distance J: 217 mm
Overall height H2: 162 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 30 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 7.4 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP216-50

Shaft d: 3 1/8 in (79.375 mm, calculated)

UC insert: UC216-50

Shaft centre height H: 88.9 mm
Mounting-bolt centre distance J: 232 mm
Housing length L: 292 mm
Insert inner-ring width B: 82.6 mm
Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN
Shaft centre height H: 88.9 mm
Housing length L: 292 mm
Source outline dimension L1: 83 mm
Housing width A: 78 mm
Foot thickness H1: 30 mm
Mounting-bolt centre distance J: 232 mm
Overall height H2: 174 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 82.6 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 35 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 9.0 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP216

Shaft d: 80 mm

UC insert: UC216

Shaft centre height H: 88.9 mm
Mounting-bolt centre distance J: 232 mm
Housing length L: 292 mm
Insert inner-ring width B: 82.6 mm
Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN
Shaft centre height H: 88.9 mm
Housing length L: 292 mm
Source outline dimension L1: 83 mm
Housing width A: 78 mm
Foot thickness H1: 30 mm
Mounting-bolt centre distance J: 232 mm
Overall height H2: 174 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 82.6 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 35 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 9.0 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP217-52

Shaft d: 3 1/4 in (82.55 mm, calculated)

UC insert: UC217-52

Shaft centre height H: 95.2 mm
Mounting-bolt centre distance J: 247 mm
Housing length L: 310 mm
Insert inner-ring width B: 85.7 mm
Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN
Shaft centre height H: 95.2 mm
Housing length L: 310 mm
Source outline dimension L1: 87 mm
Housing width A: 83 mm
Foot thickness H1: 32 mm
Mounting-bolt centre distance J: 247 mm
Overall height H2: 185 mm
Insert centre-to-face S: 34.1 mm
Insert inner-ring width B: 85.7 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 35 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 10.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP217

Shaft d: 85 mm

UC insert: UC217

Shaft centre height H: 95.2 mm
Mounting-bolt centre distance J: 247 mm
Housing length L: 310 mm
Insert inner-ring width B: 85.7 mm
Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN
Shaft centre height H: 95.2 mm
Housing length L: 310 mm
Source outline dimension L1: 87 mm
Housing width A: 83 mm
Foot thickness H1: 32 mm
Mounting-bolt centre distance J: 247 mm
Overall height H2: 185 mm
Insert centre-to-face S: 34.1 mm
Insert inner-ring width B: 85.7 mm
Mounting slot width N: 25 mm
Mounting slot length N1: 35 mm
Catalogue mounting bolt: M20
Shared catalogue mass: 10.8 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP218-56

Shaft d: 3 1/2 in (88.9 mm, calculated)

UC insert: UC218-56

Shaft centre height H: 101.6 mm
Mounting-bolt centre distance J: 262 mm
Housing length L: 327 mm
Insert inner-ring width B: 96.0 mm
Basic dynamic rating Cr: 96.1 kN
Basic static rating C0r: 71.5 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 96.1 kN
Basic static rating C0r: 71.5 kN
Shaft centre height H: 101.6 mm
Housing length L: 327 mm
Source outline dimension L1: 94 mm
Housing width A: 88 mm
Foot thickness H1: 33 mm
Mounting-bolt centre distance J: 262 mm
Overall height H2: 198 mm
Insert centre-to-face S: 39.7 mm
Insert inner-ring width B: 96.0 mm
Mounting slot width N: 27 mm
Mounting slot length N1: 40 mm
Catalogue mounting bolt: M22
Shared catalogue mass: 13.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Pillow block

UCP218

Shaft d: 90 mm

UC insert: UC218

Shaft centre height H: 101.6 mm
Mounting-bolt centre distance J: 262 mm
Housing length L: 327 mm
Insert inner-ring width B: 96.0 mm
Basic dynamic rating Cr: 96.1 kN
Basic static rating C0r: 71.5 kN

All 15 source parameters and limitations

Basic dynamic rating Cr: 96.1 kN
Basic static rating C0r: 71.5 kN
Shaft centre height H: 101.6 mm
Housing length L: 327 mm
Source outline dimension L1: 94 mm
Housing width A: 88 mm
Foot thickness H1: 33 mm
Mounting-bolt centre distance J: 262 mm
Overall height H2: 198 mm
Insert centre-to-face S: 39.7 mm
Insert inner-ring width B: 96.0 mm
Mounting slot width N: 27 mm
Mounting slot length N1: 40 mm
Catalogue mounting bolt: M22
Shared catalogue mass: 13.9 kg

H means shaft centre height in this Timken table; H2 means overall height. Do not substitute the H/H1 convention of another catalogue. Mounting slots N and N1 are not the shaft bore d.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT201

Shaft d: 12 mm

UC insert: UC201

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

The catalogue dimensions describe the take-up housing and its guide features. They do not specify the frame, available adjustment travel or a pillow-block mounting pattern. Use the complete take-up drawing for installation.

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 28. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT201-8

Shaft d: 1/2 in (12.7 mm, calculated)

UC insert: UC201-8

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT202

Shaft d: 15 mm

UC insert: UC202

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT202-10

Shaft d: 5/8 in (15.875 mm, calculated)

UC insert: UC202-10

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT203

Shaft d: 17 mm

UC insert: UC203

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT204-12

Shaft d: 3/4 in (19.05 mm, calculated)

UC insert: UC204-12

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT204

Shaft d: 20 mm

UC insert: UC204

Overall outline height H: 89 mm
Overall outline length L: 94 mm
Housing width A: 32 mm
Insert inner-ring width B: 31.0 mm
Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 12.8 kN
Basic static rating C0r: 6.7 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 61 mm
Source outline dimension A2: 21 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 94 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 12.7 mm
Insert inner-ring width B: 31.0 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT205-14

Shaft d: 7/8 in (22.225 mm, calculated)

UC insert: UC205-14

Overall outline height H: 89 mm
Overall outline length L: 97 mm
Housing width A: 32 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 62 mm
Source outline dimension A2: 24 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 97 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT205-15

Shaft d: 15/16 in (23.8125 mm, calculated)

UC insert: UC205-15

Overall outline height H: 89 mm
Overall outline length L: 97 mm
Housing width A: 32 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 62 mm
Source outline dimension A2: 24 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 97 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT205

Shaft d: 25 mm

UC insert: UC205

Overall outline height H: 89 mm
Overall outline length L: 97 mm
Housing width A: 32 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 62 mm
Source outline dimension A2: 24 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 97 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT205-16

Shaft d: 1 in (25.4 mm, calculated)

UC insert: UC205-16

Overall outline height H: 89 mm
Overall outline length L: 97 mm
Housing width A: 32 mm
Insert inner-ring width B: 34.1 mm
Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 14.0 kN
Basic static rating C0r: 7.9 kN
Overall outline height H: 89 mm
Source outline dimension H1: 76 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 62 mm
Source outline dimension A2: 24 mm
Housing width A: 32 mm
Source outline dimension N: 19 mm
Overall outline length L: 97 mm
Source outline dimension H2: 51 mm
Insert centre-to-face S: 14.3 mm
Insert inner-ring width B: 34.1 mm
Source outline dimension L3: 51 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 32 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 0.8 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT206-18

Shaft d: 1 1/8 in (28.575 mm, calculated)

UC insert: UC206-18

Overall outline height H: 102 mm
Overall outline length L: 113 mm
Housing width A: 37 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 70 mm
Source outline dimension A2: 28 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 113 mm
Source outline dimension H2: 56 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Source outline dimension L3: 57 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT206

Shaft d: 30 mm

UC insert: UC206

Overall outline height H: 102 mm
Overall outline length L: 113 mm
Housing width A: 37 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 70 mm
Source outline dimension A2: 28 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 113 mm
Source outline dimension H2: 56 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Source outline dimension L3: 57 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT206-19

Shaft d: 1 3/16 in (30.1625 mm, calculated)

UC insert: UC206-19

Overall outline height H: 102 mm
Overall outline length L: 113 mm
Housing width A: 37 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 70 mm
Source outline dimension A2: 28 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 113 mm
Source outline dimension H2: 56 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Source outline dimension L3: 57 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT206-20

Shaft d: 1 1/4 in (31.75 mm, calculated)

UC insert: UC206-20

Overall outline height H: 102 mm
Overall outline length L: 113 mm
Housing width A: 37 mm
Insert inner-ring width B: 38.1 mm
Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 19.5 kN
Basic static rating C0r: 11.3 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 10 mm
Source outline dimension L1: 70 mm
Source outline dimension A2: 28 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 113 mm
Source outline dimension H2: 56 mm
Insert centre-to-face S: 15.9 mm
Insert inner-ring width B: 38.1 mm
Source outline dimension L3: 57 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT207-20

Shaft d: 1 1/4 in (31.75 mm, calculated)

UC insert: UC207-20

Overall outline height H: 102 mm
Overall outline length L: 129 mm
Housing width A: 37 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 13 mm
Source outline dimension L1: 78 mm
Source outline dimension A2: 30 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 129 mm
Source outline dimension H2: 64 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Source outline dimension L3: 64 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT207-21

Shaft d: 1 5/16 in (33.3375 mm, calculated)

UC insert: UC207-21

Overall outline height H: 102 mm
Overall outline length L: 129 mm
Housing width A: 37 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 13 mm
Source outline dimension L1: 78 mm
Source outline dimension A2: 30 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 129 mm
Source outline dimension H2: 64 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Source outline dimension L3: 64 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT207-22

Shaft d: 1 3/8 in (34.925 mm, calculated)

UC insert: UC207-22

Overall outline height H: 102 mm
Overall outline length L: 129 mm
Housing width A: 37 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 13 mm
Source outline dimension L1: 78 mm
Source outline dimension A2: 30 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 129 mm
Source outline dimension H2: 64 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Source outline dimension L3: 64 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT207

Shaft d: 35 mm

UC insert: UC207

Overall outline height H: 102 mm
Overall outline length L: 129 mm
Housing width A: 37 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 13 mm
Source outline dimension L1: 78 mm
Source outline dimension A2: 30 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 129 mm
Source outline dimension H2: 64 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Source outline dimension L3: 64 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT207-23

Shaft d: 1 7/16 in (36.5125 mm, calculated)

UC insert: UC207-23

Overall outline height H: 102 mm
Overall outline length L: 129 mm
Housing width A: 37 mm
Insert inner-ring width B: 42.9 mm
Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 25.7 kN
Basic static rating C0r: 15.4 kN
Overall outline height H: 102 mm
Source outline dimension H1: 89 mm
Source outline dimension L2: 13 mm
Source outline dimension L1: 78 mm
Source outline dimension A2: 30 mm
Housing width A: 37 mm
Source outline dimension N: 22 mm
Overall outline length L: 129 mm
Source outline dimension H2: 64 mm
Insert centre-to-face S: 17.5 mm
Insert inner-ring width B: 42.9 mm
Source outline dimension L3: 64 mm
Source outline dimension N1: 16 mm
Source outline dimension N2: 37 mm
Source outline dimension A1: 12 mm
Shared catalogue mass: 1.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT208-24

Shaft d: 1 1/2 in (38.1 mm, calculated)

UC insert: UC208-24

Overall outline height H: 114 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Overall outline height H: 114 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 88 mm
Source outline dimension A2: 33 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT208-25

Shaft d: 1 9/16 in (39.6875 mm, calculated)

UC insert: UC208-25

Overall outline height H: 114 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Overall outline height H: 114 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 88 mm
Source outline dimension A2: 33 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT208

Shaft d: 40 mm

UC insert: UC208

Overall outline height H: 114 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 29.1 kN
Basic static rating C0r: 17.8 kN
Overall outline height H: 114 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 88 mm
Source outline dimension A2: 33 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT209-26

Shaft d: 1 5/8 in (41.275 mm, calculated)

UC insert: UC209-26

Overall outline height H: 117 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 87 mm
Source outline dimension A2: 35 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT209-27

Shaft d: 1 11/16 in (42.8625 mm, calculated)

UC insert: UC209-27

Overall outline height H: 117 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 87 mm
Source outline dimension A2: 35 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT209-28

Shaft d: 1 3/4 in (44.45 mm, calculated)

UC insert: UC209-28

Overall outline height H: 117 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 87 mm
Source outline dimension A2: 35 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT209

Shaft d: 45 mm

UC insert: UC209

Overall outline height H: 117 mm
Overall outline length L: 144 mm
Housing width A: 49 mm
Insert inner-ring width B: 49.2 mm
Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 34.1 kN
Basic static rating C0r: 21.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 87 mm
Source outline dimension A2: 35 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 144 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 49.2 mm
Source outline dimension L3: 83 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.5 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT210-30

Shaft d: 1 7/8 in (47.625 mm, calculated)

UC insert: UC210-30

Overall outline height H: 117 mm
Overall outline length L: 149 mm
Housing width A: 49 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 90 mm
Source outline dimension A2: 37 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 149 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Source outline dimension L3: 86 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.6 kg

Reference: Timken U Series Ball Bearing Housed Unit Catalog, printed page 29. Public edition retrieved 2026-10-02. Values are millimetres, kilonewtons and kilograms as labelled; inch shaft conversions use 25.4 mm per inch. Original unit markings are retained.

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT210-31

Shaft d: 1 15/16 in (49.2125 mm, calculated)

UC insert: UC210-31

Overall outline height H: 117 mm
Overall outline length L: 149 mm
Housing width A: 49 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 90 mm
Source outline dimension A2: 37 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 149 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Source outline dimension L3: 86 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT210

Shaft d: 50 mm

UC insert: UC210

Overall outline height H: 117 mm
Overall outline length L: 149 mm
Housing width A: 49 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 90 mm
Source outline dimension A2: 37 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 149 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Source outline dimension L3: 86 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT210-32

Shaft d: 2 in (50.8 mm, calculated)

UC insert: UC210-32

Overall outline height H: 117 mm
Overall outline length L: 149 mm
Housing width A: 49 mm
Insert inner-ring width B: 51.6 mm
Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 35.1 kN
Basic static rating C0r: 23.3 kN
Overall outline height H: 117 mm
Source outline dimension H1: 102 mm
Source outline dimension L2: 16 mm
Source outline dimension L1: 90 mm
Source outline dimension A2: 37 mm
Housing width A: 49 mm
Source outline dimension N: 29 mm
Overall outline length L: 149 mm
Source outline dimension H2: 83 mm
Insert centre-to-face S: 19.0 mm
Insert inner-ring width B: 51.6 mm
Source outline dimension L3: 86 mm
Source outline dimension N1: 19 mm
Source outline dimension N2: 49 mm
Source outline dimension A1: 16 mm
Shared catalogue mass: 2.6 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT211-32

Shaft d: 2 in (50.8 mm, calculated)

UC insert: UC211-32

Overall outline height H: 146 mm
Overall outline length L: 171 mm
Housing width A: 64 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 106 mm
Source outline dimension A2: 38 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 171 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Source outline dimension L3: 95 mm
Source outline dimension N1: 25 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT211-34

Shaft d: 2 1/8 in (53.975 mm, calculated)

UC insert: UC211-34

Overall outline height H: 146 mm
Overall outline length L: 171 mm
Housing width A: 64 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 106 mm
Source outline dimension A2: 38 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 171 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Source outline dimension L3: 95 mm
Source outline dimension N1: 25 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT211

Shaft d: 55 mm

UC insert: UC211

Overall outline height H: 146 mm
Overall outline length L: 171 mm
Housing width A: 64 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 106 mm
Source outline dimension A2: 38 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 171 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Source outline dimension L3: 95 mm
Source outline dimension N1: 25 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT211-35

Shaft d: 2 3/16 in (55.5625 mm, calculated)

UC insert: UC211-35

Overall outline height H: 146 mm
Overall outline length L: 171 mm
Housing width A: 64 mm
Insert inner-ring width B: 55.6 mm
Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 43.4 kN
Basic static rating C0r: 29.4 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 106 mm
Source outline dimension A2: 38 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 171 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 22.2 mm
Insert inner-ring width B: 55.6 mm
Source outline dimension L3: 95 mm
Source outline dimension N1: 25 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT212-36

Shaft d: 2 1/4 in (57.15 mm, calculated)

UC insert: UC212-36

Overall outline height H: 146 mm
Overall outline length L: 194 mm
Housing width A: 64 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 119 mm
Source outline dimension A2: 42 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 194 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 102 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT212

Shaft d: 60 mm

UC insert: UC212

Overall outline height H: 146 mm
Overall outline length L: 194 mm
Housing width A: 64 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 119 mm
Source outline dimension A2: 42 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 194 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 102 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT212-38

Shaft d: 2 3/8 in (60.325 mm, calculated)

UC insert: UC212-38

Overall outline height H: 146 mm
Overall outline length L: 194 mm
Housing width A: 64 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 119 mm
Source outline dimension A2: 42 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 194 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 102 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT212-39

Shaft d: 2 7/16 in (61.9125 mm, calculated)

UC insert: UC212-39

Overall outline height H: 146 mm
Overall outline length L: 194 mm
Housing width A: 64 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 52.4 kN
Basic static rating C0r: 36.2 kN
Overall outline height H: 146 mm
Source outline dimension H1: 130 mm
Source outline dimension L2: 19 mm
Source outline dimension L1: 119 mm
Source outline dimension A2: 42 mm
Housing width A: 64 mm
Source outline dimension N: 35 mm
Overall outline length L: 194 mm
Source outline dimension H2: 102 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 102 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 64 mm
Source outline dimension A1: 22 mm
Shared catalogue mass: 4.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT213-40

Shaft d: 2 1/2 in (63.5 mm, calculated)

UC insert: UC213-40

Overall outline height H: 167 mm
Overall outline length L: 224 mm
Housing width A: 70 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 137 mm
Source outline dimension A2: 44 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 224 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 6.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT213

Shaft d: 65 mm

UC insert: UC213

Overall outline height H: 167 mm
Overall outline length L: 224 mm
Housing width A: 70 mm
Insert inner-ring width B: 65.1 mm
Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 57.2 kN
Basic static rating C0r: 40.1 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 137 mm
Source outline dimension A2: 44 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 224 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 25.4 mm
Insert inner-ring width B: 65.1 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 6.9 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT214-44

Shaft d: 2 3/4 in (69.85 mm, calculated)

UC insert: UC214-44

Overall outline height H: 167 mm
Overall outline length L: 224 mm
Housing width A: 70 mm
Insert inner-ring width B: 74.6 mm
Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 137 mm
Source outline dimension A2: 46 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 224 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 30.2 mm
Insert inner-ring width B: 74.6 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 7.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT214

Shaft d: 70 mm

UC insert: UC214

Overall outline height H: 167 mm
Overall outline length L: 224 mm
Housing width A: 70 mm
Insert inner-ring width B: 74.6 mm
Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 62.2 kN
Basic static rating C0r: 44.1 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 137 mm
Source outline dimension A2: 46 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 224 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 30.2 mm
Insert inner-ring width B: 74.6 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 7.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT215-47

Shaft d: 2 15/16 in (74.6125 mm, calculated)

UC insert: UC215-47

Overall outline height H: 167 mm
Overall outline length L: 232 mm
Housing width A: 70 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 140 mm
Source outline dimension A2: 48 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 232 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 7.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT215

Shaft d: 75 mm

UC insert: UC215

Overall outline height H: 167 mm
Overall outline length L: 232 mm
Housing width A: 70 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 140 mm
Source outline dimension A2: 48 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 232 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 7.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT215-48

Shaft d: 3 in (76.2 mm, calculated)

UC insert: UC215-48

Overall outline height H: 167 mm
Overall outline length L: 232 mm
Housing width A: 70 mm
Insert inner-ring width B: 77.8 mm
Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 67.4 kN
Basic static rating C0r: 48.3 kN
Overall outline height H: 167 mm
Source outline dimension H1: 151 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 140 mm
Source outline dimension A2: 48 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 232 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 77.8 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 7.3 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT216-50

Shaft d: 3 1/8 in (79.375 mm, calculated)

UC insert: UC216-50

Overall outline height H: 184 mm
Overall outline length L: 235 mm
Housing width A: 70 mm
Insert inner-ring width B: 82.6 mm
Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN
Overall outline height H: 184 mm
Source outline dimension H1: 165 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 140 mm
Source outline dimension A2: 51 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 235 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 82.6 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 8.2 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT216

Shaft d: 80 mm

UC insert: UC216

Overall outline height H: 184 mm
Overall outline length L: 235 mm
Housing width A: 70 mm
Insert inner-ring width B: 82.6 mm
Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 72.7 kN
Basic static rating C0r: 53.0 kN
Overall outline height H: 184 mm
Source outline dimension H1: 165 mm
Source outline dimension L2: 21 mm
Source outline dimension L1: 140 mm
Source outline dimension A2: 51 mm
Housing width A: 70 mm
Source outline dimension N: 41 mm
Overall outline length L: 235 mm
Source outline dimension H2: 111 mm
Insert centre-to-face S: 33.3 mm
Insert inner-ring width B: 82.6 mm
Source outline dimension L3: 121 mm
Source outline dimension N1: 32 mm
Source outline dimension N2: 70 mm
Source outline dimension A1: 26 mm
Shared catalogue mass: 8.2 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT217-52

Shaft d: 3 1/4 in (82.55 mm, calculated)

UC insert: UC217-52

Overall outline height H: 198 mm
Overall outline length L: 260 mm
Housing width A: 73 mm
Insert inner-ring width B: 85.7 mm
Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN
Overall outline height H: 198 mm
Source outline dimension H1: 173 mm
Source outline dimension L2: 29 mm
Source outline dimension L1: 162 mm
Source outline dimension A2: 54 mm
Housing width A: 73 mm
Source outline dimension N: 48 mm
Overall outline length L: 260 mm
Source outline dimension H2: 124 mm
Insert centre-to-face S: 34.1 mm
Insert inner-ring width B: 85.7 mm
Source outline dimension L3: 157 mm
Source outline dimension N1: 38 mm
Source outline dimension N2: 73 mm
Source outline dimension A1: 30 mm
Shared catalogue mass: 11.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

TIMKEN · Take-up unit

UCT217

Shaft d: 85 mm

UC insert: UC217

Overall outline height H: 198 mm
Overall outline length L: 260 mm
Housing width A: 73 mm
Insert inner-ring width B: 85.7 mm
Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN

All 18 source parameters and limitations

Basic dynamic rating Cr: 84.0 kN
Basic static rating C0r: 61.9 kN
Overall outline height H: 198 mm
Source outline dimension H1: 173 mm
Source outline dimension L2: 29 mm
Source outline dimension L1: 162 mm
Source outline dimension A2: 54 mm
Housing width A: 73 mm
Source outline dimension N: 48 mm
Overall outline length L: 260 mm
Source outline dimension H2: 124 mm
Insert centre-to-face S: 34.1 mm
Insert inner-ring width B: 85.7 mm
Source outline dimension L3: 157 mm
Source outline dimension N1: 38 mm
Source outline dimension N2: 73 mm
Source outline dimension A1: 30 mm
Shared catalogue mass: 11.0 kg

Search this complete Timken designation →

A search can return no loaded product. The documented catalogue entry is still shown here; no replacement or product record has been invented.

Check more than the shaft diameter

For these Timken UCP units, H is the shaft centre height, H2 the overall height and J the mounting-bolt centre distance. The SKF table on this page uses different H/H1 meanings: compare the labels, not just the symbol. B is insert inner-ring width, not the length L of the housing.

UCT is a take-up housing for an adjustable mounting arrangement; it is not a two-foot pillow block. Its H/H1, L1/L2/L3, N/N1/N2 and A/A1/A2 dimensions describe the take-up outline and guide features. Keep those source symbols together and verify the frame geometry; the table does not specify a complete tensioning frame or adjustment travel.

One shaft diameter can have more than one housing size. For example, the 206-20 and 207-20 groups both include a 1¼-inch bore, but their mounting dimensions and basic ratings differ. Confirm the full manufacturer designation, layout, clearance, locking arrangement, lubrication, speed and actual operating loads before treating any candidate as usable. Round-bore values do not prove square- or hex-shaft compatibility.

Documented manufacturer examples

SKF UCP pillow block dimensions: metric and inch shafts

These are selected catalogue examples, not every manufacturer or every UCP model. The same housing can occur with different shaft bores. Read the complete designation, including the inch suffix.

Model or housingShaft sizeInput units

41 documented examples. Filters update immediately.

In this catalogue H1 = shaft centre height, H = overall height, L = housing length, and J = mounting-bolt centre distance. All housing dimensions below are millimetres, not the insert’s outside diameter and width. Scroll sideways on smaller screens.

SKF unit	Shaft d (mm)	Original shaft units	Centre H1 (mm)	Overall H (mm)	L (mm)	J (mm)	Housing	Details / lookup
UCP204	20	20 mm	33.3	64.29	127	95	P204	Catalogue fields A (mm) 34 A1 (mm) 20.8 B (mm) 31 H (mm) 64.29 H1 (mm) 33.3 H2 (mm) 13.49 J (mm) 95 L (mm) 127 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 18.3 Basic dynamic C (kN) 12.7 Basic static C0 (kN) 6.7 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 6500 Mass (kg) 0.66 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP205	25	25 mm	36.5	70.64	139.7	105	P205	Catalogue fields A (mm) 38.1 A1 (mm) 21.27 B (mm) 34 H (mm) 70.64 H1 (mm) 36.5 H2 (mm) 15.88 J (mm) 105 L (mm) 139.7 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 19.7 Basic dynamic C (kN) 14 Basic static C0 (kN) 7.8 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 5850 Mass (kg) 0.86 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP206	30	30 mm	42.9	83.34	165.1	121	P206	Catalogue fields A (mm) 44.6 A1 (mm) 23.6 B (mm) 38.1 H (mm) 83.34 H1 (mm) 42.9 H2 (mm) 16.67 J (mm) 121 L (mm) 165.1 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 22.2 Basic dynamic C (kN) 19.5 Basic static C0 (kN) 11.4 Fatigue load limit Pu (kN) 0.5 Limiting speed, h6 heading (r/min) 5000 Mass (kg) 1.34 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP306	30	30 mm	50	100	182	140	P306	Catalogue fields A (mm) 47 A1 (mm) 31.6 B (mm) 43 H (mm) 100 H1 (mm) 50 H2 (mm) 21 J (mm) 140 L (mm) 182 N (mm) 19 N1 (mm) 17 G (as printed) M14 s1 (mm) 26 Basic dynamic C (kN) 26.5 Basic static C0 (kN) 15 Fatigue load limit Pu (kN) 0.64 Limiting speed, h6 heading (r/min) 5300 Mass (kg) 2.15 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP207	35	35 mm	47.6	93.66	166.69	127	P207	Catalogue fields A (mm) 45.8 A1 (mm) 26.7 B (mm) 42.9 H (mm) 93.66 H1 (mm) 47.6 H2 (mm) 18.26 J (mm) 127 L (mm) 166.69 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 25.4 Basic dynamic C (kN) 25.5 Basic static C0 (kN) 15.3 Fatigue load limit Pu (kN) 0.7 Limiting speed, h6 heading (r/min) 4300 Mass (kg) 1.62 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP307	35	35 mm	56	111.4	209	160.5	P307	Catalogue fields A (mm) 54 A1 (mm) 35.8 B (mm) 48 H (mm) 111.4 H1 (mm) 56 H2 (mm) 23 J (mm) 160.5 L (mm) 209 N (mm) 24.5 N1 (mm) 17 G (as printed) M14 s1 (mm) 29 Basic dynamic C (kN) 33.2 Basic static C0 (kN) 19.3 Fatigue load limit Pu (kN) 0.815 Limiting speed, h6 heading (r/min) 4700 Mass (kg) 3 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP208	40	40 mm	49.2	101	184.15	137	P208	Catalogue fields A (mm) 48.8 A1 (mm) 29 B (mm) 49.2 H (mm) 101 H1 (mm) 49.2 H2 (mm) 20.64 J (mm) 137 L (mm) 184.15 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 30.2 Basic dynamic C (kN) 32.5 Basic static C0 (kN) 20 Fatigue load limit Pu (kN) 0.9 Limiting speed, h6 heading (r/min) 3750 Mass (kg) 2.17 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP308	40	40 mm	60	119.4	221	170.5	P308	Catalogue fields A (mm) 57 A1 (mm) 37.8 B (mm) 52 H (mm) 119.4 H1 (mm) 60 H2 (mm) 25 J (mm) 170.5 L (mm) 221 N (mm) 26.5 N1 (mm) 17 G (as printed) M14 s1 (mm) 33 Basic dynamic C (kN) 41 Basic static C0 (kN) 24 Fatigue load limit Pu (kN) 1.02 Limiting speed, h6 heading (r/min) 4200 Mass (kg) 3.55 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP209	45	45 mm	54	107.95	189.71	146	P209	Catalogue fields A (mm) 51.2 A1 (mm) 29.3 B (mm) 49.2 H (mm) 107.95 H1 (mm) 54 H2 (mm) 19.05 J (mm) 146 L (mm) 189.71 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 30.2 Basic dynamic C (kN) 32.5 Basic static C0 (kN) 20.4 Fatigue load limit Pu (kN) 0.9 Limiting speed, h6 heading (r/min) 3400 Mass (kg) 2.4 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP309	45	45 mm	67	136	247	190	P309	Catalogue fields A (mm) 63 A1 (mm) 41.8 B (mm) 57 H (mm) 136 H1 (mm) 67 H2 (mm) 25 J (mm) 190 L (mm) 247 N (mm) 29 N1 (mm) 20 G (as printed) M16 s1 (mm) 35 Basic dynamic C (kN) 52.7 Basic static C0 (kN) 32 Fatigue load limit Pu (kN) 1.34 Limiting speed, h6 heading (r/min) 3750 Mass (kg) 5.05 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP210	50	50 mm	57.2	115.89	206.38	159	P210	Catalogue fields A (mm) 55.6 A1 (mm) 30.7 B (mm) 51.6 H (mm) 115.89 H1 (mm) 57.2 H2 (mm) 19.05 J (mm) 159 L (mm) 206.38 N (mm) 22 N1 (mm) 20 G (as printed) M16 s1 (mm) 32.6 Basic dynamic C (kN) 35.1 Basic static C0 (kN) 23.2 Fatigue load limit Pu (kN) 1 Limiting speed, h6 heading (r/min) 3300 Mass (kg) 2.88 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP310	50	50 mm	75	152	275	212.5	P310	Catalogue fields A (mm) 65 A1 (mm) 43 B (mm) 61 H (mm) 152 H1 (mm) 75 H2 (mm) 25 J (mm) 212.5 L (mm) 275 N (mm) 34.5 N1 (mm) 20 G (as printed) M16 s1 (mm) 39 Basic dynamic C (kN) 61.8 Basic static C0 (kN) 38 Fatigue load limit Pu (kN) 1.6 Limiting speed, h6 heading (r/min) 3400 Mass (kg) 6.4 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP211	55	55 mm	63.5	126.21	219.08	171	P211	Catalogue fields A (mm) 58.9 A1 (mm) 34.6 B (mm) 55.6 H (mm) 126.21 H1 (mm) 63.5 H2 (mm) 22.23 J (mm) 171 L (mm) 219.08 N (mm) 22 N1 (mm) 20 G (as printed) M16 s1 (mm) 33.4 Basic dynamic C (kN) 43.6 Basic static C0 (kN) 29 Fatigue load limit Pu (kN) 1.3 Limiting speed, h6 heading (r/min) 3000 Mass (kg) 3.95 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP311	55	55 mm	80	162	302	236.5	P311	Catalogue fields A (mm) 68 A1 (mm) 45 B (mm) 66 H (mm) 162 H1 (mm) 80 H2 (mm) 25 J (mm) 236.5 L (mm) 302 N (mm) 37.5 N1 (mm) 20 G (as printed) M16 s1 (mm) 41 Basic dynamic C (kN) 71.5 Basic static C0 (kN) 45 Fatigue load limit Pu (kN) 1.9 Limiting speed, h6 heading (r/min) 3100 Mass (kg) 7.8 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Source limitation: The insert designation has a typographical conflict in this catalogue; an insert replacement is not inferred. Search records →
UCP212	60	60 mm	69.8	141.29	239.71	184	P212	Catalogue fields A (mm) 61.6 A1 (mm) 34.3 B (mm) 65.1 H (mm) 141.29 H1 (mm) 69.8 H2 (mm) 22.23 J (mm) 184 L (mm) 239.71 N (mm) 25 N1 (mm) 20 G (as printed) M16 s1 (mm) 39.7 Basic dynamic C (kN) 52.7 Basic static C0 (kN) 36 Fatigue load limit Pu (kN) 1.5 Limiting speed, h6 heading (r/min) 2700 Mass (kg) 5.05 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP312	60	60 mm	85	170.8	321	250.5	Not verified	Catalogue fields A (mm) 72 A1 (mm) 47.8 B (mm) 71 H (mm) 170.8 H1 (mm) 85 H2 (mm) 35 J (mm) 250.5 L (mm) 321 N (mm) 36.5 N1 (mm) 24 G (as printed) M20 s1 (mm) 45 Basic dynamic C (kN) 81.9 Basic static C0 (kN) 52 Fatigue load limit Pu (kN) 2.2 Limiting speed, h6 heading (r/min) 2900 Mass (kg) 9.6 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Source limitation: The catalogue prints P3112 in the housing column. Housing identity is withheld pending confirmation; the unit is printed UCP312. Search records →
UCP213	65	65 mm	76.2	153.59	265.11	203	P213	Catalogue fields A (mm) 71.9 A1 (mm) 34.9 B (mm) 65.1 H (mm) 153.59 H1 (mm) 76.2 H2 (mm) 25.4 J (mm) 203 L (mm) 265.11 N (mm) 30 N1 (mm) 25 G (as printed) M20 s1 (mm) 39.7 Basic dynamic C (kN) 57.2 Basic static C0 (kN) 40 Fatigue load limit Pu (kN) 1.7 Limiting speed, h6 heading (r/min) 2350 Mass (kg) 6.63 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP214	70	70 mm	79.4	159.54	265.91	210	P214	Catalogue fields A (mm) 72.1 A1 (mm) 40.5 B (mm) 74.6 H (mm) 159.54 H1 (mm) 79.4 H2 (mm) 28.18 J (mm) 210 L (mm) 265.91 N (mm) 30 N1 (mm) 25 G (as printed) M20 s1 (mm) 44.4 Basic dynamic C (kN) 62.4 Basic static C0 (kN) 44 Fatigue load limit Pu (kN) 1.9 Limiting speed, h6 heading (r/min) 2250 Mass (kg) 7.17 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP215	75	75 mm	82.6	166	271.47	217	P215	Catalogue fields A (mm) 73 A1 (mm) 42 B (mm) 77.8 H (mm) 166 H1 (mm) 82.6 H2 (mm) 25.4 J (mm) 217 L (mm) 271.47 N (mm) 30 N1 (mm) 25 G (as printed) M20 s1 (mm) 44.5 Basic dynamic C (kN) 66.3 Basic static C0 (kN) 49 Fatigue load limit Pu (kN) 2 Limiting speed, h6 heading (r/min) 2100 Mass (kg) 8.17 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP315	75	75 mm	100	202	368	290.5	P315	Catalogue fields A (mm) 86 A1 (mm) 57.6 B (mm) 82 H (mm) 202 H1 (mm) 100 H2 (mm) 40 J (mm) 290.5 L (mm) 368 N (mm) 39.5 N1 (mm) 27 G (as printed) M22 s1 (mm) 50 Basic dynamic C (kN) 114 Basic static C0 (kN) 76.5 Fatigue load limit Pu (kN) 3 Limiting speed, h6 heading (r/min) 2300 Mass (kg) 15.5 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP216	80	80 mm	88.9	176.21	292.1	232	P216	Catalogue fields A (mm) 77.8 A1 (mm) 45.2 B (mm) 82.6 H (mm) 176.21 H1 (mm) 88.9 H2 (mm) 34 J (mm) 232 L (mm) 292.1 N (mm) 35 N1 (mm) 25 G (as printed) M20 s1 (mm) 49.3 Basic dynamic C (kN) 71.5 Basic static C0 (kN) 54 Fatigue load limit Pu (kN) 2.2 Limiting speed, h6 heading (r/min) 1900 Mass (kg) 9.3 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP316	80	80 mm	106	215	378	300.5	P316	Catalogue fields A (mm) 93 A1 (mm) 61.8 B (mm) 86 H (mm) 215 H1 (mm) 106 H2 (mm) 40 J (mm) 300.5 L (mm) 378 N (mm) 39.5 N1 (mm) 27 G (as printed) M22 s1 (mm) 52 Basic dynamic C (kN) 124 Basic static C0 (kN) 86.5 Fatigue load limit Pu (kN) 3.25 Limiting speed, h6 heading (r/min) 2150 Mass (kg) 18.2 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP217	85	85 mm	95.2	188.91	310.36	247	P217	Catalogue fields A (mm) 83.2 A1 (mm) 47.6 B (mm) 85.7 H (mm) 188.91 H1 (mm) 95.2 H2 (mm) 36 J (mm) 247 L (mm) 310.36 N (mm) 35 N1 (mm) 25 G (as printed) M20 s1 (mm) 51.6 Basic dynamic C (kN) 83.2 Basic static C0 (kN) 64 Fatigue load limit Pu (kN) 2.5 Limiting speed, h6 heading (r/min) 1800 Mass (kg) 12.9 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP218	90	90 mm	101.6	202.41	327.03	262	P218	Catalogue fields A (mm) 88 A1 (mm) 50.8 B (mm) 96 H (mm) 202.41 H1 (mm) 101.6 H2 (mm) 38 J (mm) 262 L (mm) 327.03 N (mm) 40 N1 (mm) 27 G (as printed) M22 s1 (mm) 56.3 Basic dynamic C (kN) 95.6 Basic static C0 (kN) 72 Fatigue load limit Pu (kN) 2.7 Limiting speed, h6 heading (r/min) 1600 Mass (kg) 14.5 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP320	100	100 mm	140	283	482	380	P320	Catalogue fields A (mm) 107 A1 (mm) 71.4 B (mm) 108 H (mm) 283 H1 (mm) 140 H2 (mm) 55 J (mm) 380 L (mm) 482 N (mm) 49.5 N1 (mm) 36 G (as printed) M30 s1 (mm) 66 Basic dynamic C (kN) 174 Basic static C0 (kN) 140 Fatigue load limit Pu (kN) 4.75 Limiting speed, h6 heading (r/min) 1700 Mass (kg) 36.7 SKF UC range publication 17273, printed pages 8–9. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP204-12	19.05	3/4 in	33.3	64.29	127	95	P204	Catalogue fields A (mm) 34 A1 (mm) 20.8 B (mm) 31 H (mm) 64.29 H1 (mm) 33.3 H2 (mm) 13.49 J (mm) 95 L (mm) 127 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 18.3 Basic dynamic C (kN) 12.7 Basic static C0 (kN) 6.7 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 6500 Mass (kg) 0.67 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP205-14	22.225	7/8 in	36.5	70.64	139.7	105	P205	Catalogue fields A (mm) 38.1 A1 (mm) 21.27 B (mm) 34 H (mm) 70.64 H1 (mm) 36.5 H2 (mm) 15.88 J (mm) 105 L (mm) 139.7 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 19.7 Basic dynamic C (kN) 14 Basic static C0 (kN) 7.8 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 5850 Mass (kg) 0.89 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP205-15	23.813	15/16 in	36.5	70.64	139.7	105	P205	Catalogue fields A (mm) 38.1 A1 (mm) 21.27 B (mm) 34 H (mm) 70.64 H1 (mm) 36.5 H2 (mm) 15.88 J (mm) 105 L (mm) 139.7 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 19.7 Basic dynamic C (kN) 14 Basic static C0 (kN) 7.8 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 5850 Mass (kg) 0.88 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP205-16	25.4	1 in	36.5	70.64	139.7	105	P205	Catalogue fields A (mm) 38.1 A1 (mm) 21.27 B (mm) 34 H (mm) 70.64 H1 (mm) 36.5 H2 (mm) 15.88 J (mm) 105 L (mm) 139.7 N (mm) 18 N1 (mm) 13 G (as printed) M10 s1 (mm) 19.7 Basic dynamic C (kN) 14 Basic static C0 (kN) 7.8 Fatigue load limit Pu (kN) 0.3 Limiting speed, h6 heading (r/min) 5850 Mass (kg) 0.86 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP206-18	28.575	1 1/8 in	42.9	83.34	165.1	121	P206	Catalogue fields A (mm) 44.6 A1 (mm) 23.6 B (mm) 38.1 H (mm) 83.34 H1 (mm) 42.9 H2 (mm) 16.67 J (mm) 121 L (mm) 165.1 N (mm) 21 N1 (mm) 17 G (as printed) M10 s1 (mm) 22.2 Basic dynamic C (kN) 19.5 Basic static C0 (kN) 11.4 Fatigue load limit Pu (kN) 0.5 Limiting speed, h6 heading (r/min) 5000 Mass (kg) 1.36 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP206-19	30.163	1 3/16 in	42.9	83.34	165.1	121	P206	Catalogue fields A (mm) 44.6 A1 (mm) 23.6 B (mm) 38.1 H (mm) 83.34 H1 (mm) 42.9 H2 (mm) 16.67 J (mm) 121 L (mm) 165.1 N (mm) 21 N1 (mm) 17 G (as printed) M10 s1 (mm) 22.2 Basic dynamic C (kN) 19.5 Basic static C0 (kN) 11.4 Fatigue load limit Pu (kN) 0.5 Limiting speed, h6 heading (r/min) 5000 Mass (kg) 1.34 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP207-20	31.75	1 1/4 in	47.6	93.66	166.69	127	P207	Catalogue fields A (mm) 45.8 A1 (mm) 26.7 B (mm) 42.9 H (mm) 93.66 H1 (mm) 47.6 H2 (mm) 18.26 J (mm) 127 L (mm) 166.69 N (mm) 21 N1 (mm) 17 G (as printed) M12 s1 (mm) 25.4 Basic dynamic C (kN) 25.5 Basic static C0 (kN) 15.3 Fatigue load limit Pu (kN) 0.7 Limiting speed, h6 heading (r/min) 4300 Mass (kg) 1.67 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP207-22	34.925	1 3/8 in	47.6	93.66	166.69	127	P207	Catalogue fields A (mm) 45.8 A1 (mm) 26.7 B (mm) 42.9 H (mm) 93.66 H1 (mm) 47.6 H2 (mm) 18.26 J (mm) 127 L (mm) 166.69 N (mm) 21 N1 (mm) 17 G (as printed) M12 s1 (mm) 25.4 Basic dynamic C (kN) 25.5 Basic static C0 (kN) 15.3 Fatigue load limit Pu (kN) 0.7 Limiting speed, h6 heading (r/min) 4300 Mass (kg) 1.62 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP207-23	36.513	1 7/16 in	47.6	93.66	166.69	127	P207	Catalogue fields A (mm) 45.8 A1 (mm) 26.7 B (mm) 42.9 H (mm) 93.66 H1 (mm) 47.6 H2 (mm) 18.26 J (mm) 127 L (mm) 166.69 N (mm) 21 N1 (mm) 17 G (as printed) M12 s1 (mm) 25.4 Basic dynamic C (kN) 25.5 Basic static C0 (kN) 15.3 Fatigue load limit Pu (kN) 0.7 Limiting speed, h6 heading (r/min) 4300 Mass (kg) 1.59 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP208-24	38.1	1 1/2 in	49.2	101	184.15	137	P208	Catalogue fields A (mm) 48.8 A1 (mm) 29 B (mm) 49.2 H (mm) 101 H1 (mm) 49.2 H2 (mm) 20.64 J (mm) 137 L (mm) 184.15 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 30.2 Basic dynamic C (kN) 32.5 Basic static C0 (kN) 20 Fatigue load limit Pu (kN) 0.9 Limiting speed, h6 heading (r/min) 3750 Mass (kg) 2.22 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP209-28	44.45	1 3/4 in	54	107.95	189.71	146	P209	Catalogue fields A (mm) 51.2 A1 (mm) 29.3 B (mm) 49.2 H (mm) 107.95 H1 (mm) 54 H2 (mm) 19.05 J (mm) 146 L (mm) 189.71 N (mm) 21 N1 (mm) 17 G (as printed) M14 s1 (mm) 30.2 Basic dynamic C (kN) 32.5 Basic static C0 (kN) 20.4 Fatigue load limit Pu (kN) 0.9 Limiting speed, h6 heading (r/min) 3400 Mass (kg) 2.41 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP211-32	50.8	2 in	63.5	126.21	219.08	171	P211	Catalogue fields A (mm) 58.9 A1 (mm) 34.6 B (mm) 55.6 H (mm) 126.21 H1 (mm) 63.5 H2 (mm) 22.23 J (mm) 171 L (mm) 219.08 N (mm) 22 N1 (mm) 20 G (as printed) M16 s1 (mm) 33.4 Basic dynamic C (kN) 43.6 Basic static C0 (kN) 29 Fatigue load limit Pu (kN) 1.3 Limiting speed, h6 heading (r/min) 3000 Mass (kg) 4.1 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP212-36	57.15	2 1/4 in	69.8	141.29	239.71	184	P212	Catalogue fields A (mm) 61.6 A1 (mm) 34.3 B (mm) 65.1 H (mm) 141.29 H1 (mm) 69.8 H2 (mm) 22.23 J (mm) 184 L (mm) 239.71 N (mm) 25 N1 (mm) 20 G (as printed) M16 s1 (mm) 39.7 Basic dynamic C (kN) 52.7 Basic static C0 (kN) 36 Fatigue load limit Pu (kN) 1.5 Limiting speed, h6 heading (r/min) 2700 Mass (kg) 5.18 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP213-40	63.5	2 1/2 in	76.2	153.59	265.11	203	P213	Catalogue fields A (mm) 71.9 A1 (mm) 34.9 B (mm) 65.1 H (mm) 153.59 H1 (mm) 76.2 H2 (mm) 25.4 J (mm) 203 L (mm) 265.11 N (mm) 30 N1 (mm) 25 G (as printed) M16 s1 (mm) 39.7 Basic dynamic C (kN) 57.2 Basic static C0 (kN) 40 Fatigue load limit Pu (kN) 1.7 Limiting speed, h6 heading (r/min) 2350 Mass (kg) 6.7 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP315-48	76.2	3 in	100	202.7	368	290	P315	Catalogue fields A (mm) 86 A1 (mm) 57.6 B (mm) 82 H (mm) 202.7 H1 (mm) 100 H2 (mm) 40 J (mm) 290 L (mm) 368 N (mm) 39.5 N1 (mm) 27 G (as printed) 22 s1 (mm) 50 Basic dynamic C (kN) 114 Basic static C0 (kN) 76.5 Fatigue load limit Pu (kN) 3 Limiting speed, h6 heading (r/min) 2300 Mass (kg) 15.4 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →
UCP320-64	101.6	4 in	140	283.7	482	380	P320	Catalogue fields A (mm) 107 A1 (mm) 71.4 B (mm) 108 H (mm) 283.7 H1 (mm) 140 H2 (mm) 55 J (mm) 380 L (mm) 482 N (mm) 49.5 N1 (mm) 36 G (as printed) 30 s1 (mm) 66 Basic dynamic C (kN) 174 Basic static C0 (kN) 140 Fatigue load limit Pu (kN) 4.75 Limiting speed, h6 heading (r/min) 1700 Mass (kg) 36.4 SKF UC range publication 17273, printed pages 10–11. Basic ratings are not an assembled-machine allowable-load approval. The speed heading specifies h6 shaft tolerance. Search records →

Source: SKF insert bearing units, UC range, publication 17273, metric and inch pillow-block tables. Reviewed 2026-10-01. The reference table is independent of product availability in the site database; a search may have no loaded product. No blank specification is inferred from a neighbouring size.

Complete unit, not an empty housing

FAG pillow block shaft-size reference

Match the shaft bore first, then inspect the complete unit’s mounting dimensions and component markings. These manufacturer-labelled examples complement the SKF tables; they are not cross-brand replacement approvals.

Unit or component markingShaft bore d (mm)

9 documented units. Filters update as you type.

Enter the actual bore in millimetres. For an inch shaft, convert the full fraction first; this reference preserves the source’s reported precision. Scroll the table sideways on a narrow screen.

Complete FAG unit	Shaft d (mm)	Mounting layout	Housing dimensions (mm)	Component details
UELP205	25	Long-base pillow block	Base length L = 140Bolt spacing J = 105Shaft centre H = 36.5	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 25 mm Length total · L 140 mm Height · H2 71 mm Basic dynamic load rating, radial · Cr 14,900 N Basic static load rating, radial · C0r 7,800 N Mass · ≈m 0.84 kg Distance fixing bore · J 105 mm Width (slot) · N 13 mm Length (slot) · N1 19 mm Distance shaft axis · H 36.5 mm Width (base) · A 38 mm Width (head) · A1 23 mm Height (base) · H1 15 mm Locking collar total width · B1 44.5 mm Distance of raceway to locking collar · S1 27 mm Connection thread for lubrication · Q M6 Housing GEHP205-GG Bearing designation UEL205 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP205. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP205 record →
UELP206	30	Long-base pillow block	Base length L = 165Bolt spacing J = 121Shaft centre H = 42.9	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 30 mm Length total · L 165 mm Height · H2 83 mm Basic dynamic load rating, radial · Cr 20,700 N Basic static load rating, radial · C0r 11,300 N Mass · ≈m 1.36 kg Distance fixing bore · J 121 mm Width (slot) · N 17 mm Length (slot) · N1 21 mm Distance shaft axis · H 42.9 mm Width (base) · A 48 mm Width (head) · A1 25 mm Height (base) · H1 17 mm Locking collar total width · B1 48.5 mm Distance of raceway to locking collar · S1 30.2 mm Connection thread for lubrication · Q M6 Housing GEHP206-GG Bearing designation UEL206 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP206. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP206 record →
UELP207	35	Long-base pillow block	Base length L = 167Bolt spacing J = 127Shaft centre H = 47.6	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 35 mm Length total · L 167 mm Height · H2 93 mm Basic dynamic load rating, radial · Cr 27,500 N Basic static load rating, radial · C0r 15,300 N Mass · ≈m 1.68 kg Distance fixing bore · J 127 mm Width (slot) · N 17 mm Length (slot) · N1 21 mm Distance shaft axis · H 47.6 mm Width (base) · A 48 mm Width (head) · A1 26 mm Height (base) · H1 18 mm Locking collar total width · B1 51.3 mm Distance of raceway to locking collar · S1 32.5 mm Connection thread for lubrication · Q M6 Housing GEHP207-GG Bearing designation UEL207 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP207. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP207 record →
UELP208	40	Long-base pillow block	Base length L = 184Bolt spacing J = 137Shaft centre H = 49.2	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 40 mm Length total · L 184 mm Height · H2 99 mm Basic dynamic load rating, radial · Cr 34,500 N Basic static load rating, radial · C0r 19,800 N Mass · ≈m 2.07 kg Distance fixing bore · J 137 mm Width (slot) · N 17 mm Length (slot) · N1 21 mm Distance shaft axis · H 49.2 mm Width (base) · A 54 mm Width (head) · A1 29 mm Height (base) · H1 18 mm Locking collar total width · B1 56.5 mm Distance of raceway to locking collar · S1 35.1 mm Connection thread for lubrication · Q M6 Housing GEHP208-GG Bearing designation UEL208 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP208. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP208 record →
UELP209	45	Long-base pillow block	Base length L = 190Bolt spacing J = 146Shaft centre H = 54	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 45 mm Length total · L 190 mm Height · H2 106 mm Basic dynamic load rating, radial · Cr 34,500 N Basic static load rating, radial · C0r 20,400 N Mass · ≈m 2.55 kg Distance fixing bore · J 146 mm Width (slot) · N 17 mm Length (slot) · N1 21 mm Distance shaft axis · H 54 mm Width (base) · A 54 mm Width (head) · A1 30 mm Height (base) · H1 20 mm Locking collar total width · B1 56.5 mm Distance of raceway to locking collar · S1 35.1 mm Connection thread for lubrication · Q M6 Housing GEHP209-GG Bearing designation UEL209 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP209. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP209 record →
UELP210	50	Long-base pillow block	Base length L = 206Bolt spacing J = 159Shaft centre H = 57.2	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 50 mm Length total · L 206 mm Height · H2 114 mm Basic dynamic load rating, radial · Cr 37,500 N Basic static load rating, radial · C0r 23,200 N Mass · ≈m 2.95 kg Distance fixing bore · J 159 mm Width (slot) · N 20 mm Length (slot) · N1 25 mm Distance shaft axis · H 57.2 mm Width (base) · A 60 mm Width (head) · A1 31 mm Height (base) · H1 21 mm Locking collar total width · B1 62.8 mm Distance of raceway to locking collar · S1 38.2 mm Connection thread for lubrication · Q M6 Housing GEHP210-GG Bearing designation UEL210 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP210. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP210 record →
UELP211	55	Long-base pillow block	Base length L = 219Bolt spacing J = 171Shaft centre H = 63.5	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 55 mm Length total · L 219 mm Height · H2 126 mm Basic dynamic load rating, radial · Cr 46,000 N Basic static load rating, radial · C0r 29,000 N Mass · ≈m 3.69 kg Distance fixing bore · J 171 mm Width (slot) · N 20 mm Length (slot) · N1 25 mm Distance shaft axis · H 63.5 mm Width (base) · A 60 mm Width (head) · A1 32 mm Height (base) · H1 23 mm Locking collar total width · B1 71.4 mm Distance of raceway to locking collar · S1 43.6 mm Connection thread for lubrication · Q M6 Housing GEHP211-GG Bearing designation UEL211 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP211. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP211 record →
UELP212	60	Long-base pillow block	Base length L = 241Bolt spacing J = 184Shaft centre H = 69.8	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 60 mm Length total · L 241 mm Height · H2 138 mm Basic dynamic load rating, radial · Cr 56,000 N Basic static load rating, radial · C0r 36,000 N Mass · ≈m 4.94 kg Distance fixing bore · J 184 mm Width (slot) · N 20 mm Length (slot) · N1 25 mm Distance shaft axis · H 69.8 mm Width (base) · A 70 mm Width (head) · A1 34 mm Height (base) · H1 25 mm Locking collar total width · B1 77.9 mm Distance of raceway to locking collar · S1 46.9 mm Connection thread for lubrication · Q M6 Housing GEHP212-GG Bearing designation UEL212 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP212. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP212 record →
UELP216	80	Long-base pillow block	Base length L = 292Bolt spacing J = 232Shaft centre H = 88.9	View 20 fields Long-base cast-iron pillow block unit, with an eccentric-locking-collar insert and RSR seals. Bore diameter · d 80 mm Length total · L 292 mm Height · H2 175 mm Basic dynamic load rating, radial · Cr 76,000 N Basic static load rating, radial · C0r 54,000 N Mass · ≈m 8.5 kg Distance fixing bore · J 232 mm Width (slot) · N 25 mm Length (slot) · N1 31 mm Distance shaft axis · H 88.9 mm Width (base) · A 78 mm Width (head) · A1 44 mm Height (base) · H1 30 mm Locking collar total width · B1 70.7 mm Distance of raceway to locking collar · S1 47.3 mm Connection thread for lubrication · Q M6 Housing GEHP216-GG Bearing designation UEL216 Operating temperature min. · Tmin -20 °C Operating temperature max. · Tmax 120 °C Source: Schaeffler medias, FAG UELP216. Original product record captured 2026-09-02. Labels and symbols are retained from that record. A missing field is not filled from another size or manufacturer. Basic bearing load ratings do not establish the permissible load of the housing, bolts or assembled machine. Temperature values belong to this specific record, not every unit in the series. Open full UELP216 record →

No match means no verified example in this subset. It does not mean the requested bore, construction or material is unavailable. Use the original designation and mounting drawing before choosing an insert, housing or complete assembly.

Continue with the exact component

Insert bearing details →Housing-only identification →Drawings and named dimensions →Search the full designation →Check replacement evidence →UCF / UCFL / UCFC dimensions →

These reference pages do not sell bearings or approve a replacement. Keep the manufacturer, full designation, source edition and unresolved installation requirements with each comparison.

Application starting points

Where this family is used

Conveyors, agricultural drives and supported shafts.

Read equipment selection guides →

Do not skip

Selection and interchange checks

Match shaft size, bolt centres, housing style and shaft locking; a matching insert alone does not establish unit interchangeability.

Full verification checklist →

Database-backed results

Mounted bearing units — actual products

4,430 records

First 12 records. Open all results to filter brands and technical attributes. These are search candidates, not approved replacements.

Brand / complete designation	Type	d×D×B (mm)	Closure	Original precision	Clearance
INABA25-XL	Flanged housing unit	25×95×—	Not reported	Not reported	Not reported
INABLCTE30-XL	Flanged housing unit	30×84×—	Not reported	Not reported	Not reported
KOYOBLF201	Ball bearing unit	12×—×—	Not reported	Not reported	Not reported
KOYOBLF202	Ball bearing unit	15×—×—	Not reported	Not reported	Not reported
KOYOBLF203	Ball bearing unit	17×—×—	Not reported	Not reported	Not reported
KOYOBLF204	Ball bearing unit	20×—×—	Not reported	Not reported	Not reported
KOYOBLF205	Ball bearing unit	25×—×—	Not reported	Not reported	Not reported
KOYOBLF206	Ball bearing unit	30×—×—	Not reported	Not reported	Not reported
KOYOBLF207	Ball bearing unit	35×—×—	Not reported	Not reported	Not reported
KOYOBLP201	Ball bearing unit	12×—×22	Not reported	Not reported	Not reported
KOYOBLP202	Ball bearing unit	15×—×22	Not reported	Not reported	Not reported
KOYOBLP203	Ball bearing unit	17×—×22	Not reported	Not reported	Not reported

— = not recorded. Width conventions differ for tapered assemblies, thrust bearings and mounted units. Always inspect the dimensional drawing.

Filter all 4,430 records →

All recorded subtypes in this family

Original catalogue descriptions are preserved in the records. Identical display names, including singular/plural variants, share one combined entry. Selecting a subtype opens its brand and technical filters.

Find a subtype

Ball bearing units402 Damping carriage, recirculating roller bearing unit22 Flanged housing unit1,030 Guideways for linear recirculating ball bearing unit4 Icos oil-sealed bearing unit3 Linear ball bearing and housing unit149 Linear plain bearing and housing unit14 Linear recirculating ball bearing unit3 Linear recirculating roller bearing unit35 Plummer block housing units2,494 Take-up housing unit274

Reference basis & data limits

Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.

Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.

Find a Dodge mounted bearing by shaft size

Compare mounting dimensions

What is this bearing type?

Variants that change the answer

What the family name cannot tell you

Identify the exact part before comparing

Pillow bearing, pillow block and mounted bearing: what do the names mean?

Pillow block vs flange vs take-up unit

1 inch is 25.4 mm, not 25 mm

Can I search a fraction such as 3/4 or 1 1/2?

Does a shared housing prove the same shaft bore?

Why did my shaft-size search return no examples?

Which dimensions belong in a pillow-block size chart?

UCP vs UCF vs UCFL vs UCFC: what changes?

Inch suffixes, rounded millimetres and missing sizes

From shaft bore to a complete pillow block: compare the right dimensions

Timken pillow blocks and take-up units: shaft sizes and dimensions

UCP201

UCP201-8

UCP202

UCP202-10

UCP203

UCP204-12

UCP204

UCP205-14

UCP205-15

UCP205

UCP205-16

UCP206-18

UCP206

UCP206-19

UCP206-20

UCP207-20

UCP207-21

UCP207-22

UCP207

UCP207-23

UCP208-24

UCP208-25

UCP208

UCP209-26

UCP209-27

UCP209-28

UCP209

UCP210-30

UCP210-31

UCP210

UCP210-32

UCP211-32

UCP211-34

UCP211

UCP211-35

UCP212-36

UCP212

UCP212-38

UCP212-39

UCP213-40

UCP213

UCP214-44

UCP214

UCP215-47

UCP215

UCP215-48

UCP216-50

UCP216

UCP217-52

UCP217

UCP218-56

UCP218

UCT201

UCT201-8

UCT202

UCT202-10

UCT203

UCT204-12

UCT204

UCT205-14

UCT205-15

UCT205

UCT205-16