L44610 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with L44610. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page7 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
TIMKEN L44610 — individual cup dimensions
TIMKEN L44610 is an individual tapered-roller cup (outer ring), not the complete cone-and-cup bearing. The manufacturer lists outside diameter D = 50.292 mm (1.9800 in) and outer-ring width C = 10.668 mm (0.4200 in).
| Measurement | Symbol | Metric | Inches |
|---|---|---|---|
| O.D. (D) | D | 50.292 mm | 1.9800 in |
| Outer Ring Width (C) | C | 10.668 mm | 0.4200 in |
| Max Housing Fillet Radius | Not specified | 1.27 mm | 0.050 in |
| Housing Backing Shoulder Dia. - Frontface (Da) | Da | 47.50 mm | 1.87 in |
| Housing Backing Shoulder Dia. - Backface (Db) | Db | 44.45 mm | 1.75 in |
Use the component number correctly
- D is the nominal cup outside diameter. C measures this outer ring only; it is not the assembled bearing width T. This single-cup record does not establish a shaft bore d or a matching cone.
- Preserve the full component number and its suffix. A shared prefix, similar ring size or a related-products suggestion does not approve a cone/cup combination or a cross-brand replacement.
- For a complete bearing, check both component markings and the manufacturer’s assembled d×D×T record. B+C is not a valid way to calculate T. A seal, axle rating, vehicle application and tightening procedure need their own evidence.
Factual reference: Timken official individual-component catalogue; source snapshot 2026-10-02. Original interpretation by BearingScope. These measurements do not certify a complete assembly, fit or interchange.
TIMKEN L44610 — bearing pairs and set identification
For TIMKEN L44610, the component number alone does not establish every dimension of a complete bearing. This reference identifies documented cone/cup combinations that contain L44610; select the row matching both of your component markings.
Which components make up the set?
| TIMKEN set | Cone | Cup | Reference / package scope |
|---|---|---|---|
| SET4 | L44649 | L44610 | 2002 · historical package |
| SET14 | L44643 | L44610 | 2002 · historical package |
Complete bearing dimensions by exact pair
These TS single-row tapered-roller combinations are reproduced as factual measurements from the 2002 reference. Dimensions are not a fitment approval or a current availability claim. Each cell keeps both published units.
| Cone / cup | Bore d | Outside D | Assembly T |
|---|---|---|---|
| L44640 / L44610 | 23.812 mm 0.938 in | 50.292 mm 1.980 in | 14.224 mm 0.560 in |
| L44643 / L44610 | 25.400 mm 1.000 in | 50.292 mm 1.980 in | 14.224 mm 0.560 in |
| L44642 / L44610 | 25.400 mm 1.000 in | 50.292 mm 1.980 in | 14.224 mm 0.560 in |
| L44649 / L44610 | 26.987 mm 1.063 in | 50.292 mm 1.980 in | 14.224 mm 0.560 in |
Separate ring widths B / C and source page references
B and C below describe separate components. Their sum is not the assembly width T.
| Cone / cup | Cone width B | Cup width C | 2002 PDF pages |
|---|---|---|---|
| L44640 / L44610 | 14.732 mm 0.580 in | 10.668 mm 0.420 in | 205, 377 |
| L44643 / L44610 | 14.732 mm 0.580 in | 10.668 mm 0.420 in | 208, 377 |
| L44642 / L44610 | 14.732 mm 0.580 in | 10.668 mm 0.420 in | 208, 377 |
| L44649 / L44610 | 14.732 mm 0.580 in | 10.668 mm 0.420 in | 210, 378 |
What to confirm before using this reference
- d is the cone bore, D is the cup outside diameter and T is the complete bearing width for the exact pair. B and C measure the separate rings; do not add B and C to calculate T.
- The dimensional table is a historical identification reference from the 2002 Timken Bearing Specification Guide, not a current engineering drawing. Printed metric and inch values are retained, including their original rounding. Check the current drawing before specifying fits or machining.
- A component may appear with several mating numbers. A match here documents that exact Timken combination; it does not approve other suffixes, mixed-brand rings, a vehicle application or a substitute with similar dimensions.
- A cone-and-cup set is not automatically a complete wheel-end repair kit. Seal numbers, collars, spacers and quantities must be confirmed separately unless the specific set note below explicitly lists them.
- For replacement work, inspect and replace the mating cup and cone together as specified for the assembly. Retaining a worn ring or mixing manufacturer geometries can change the contact pattern even when nominal diameters match.
- An axle tightening torque, preload or endplay target cannot be derived from these dimensions. Use the procedure for the identified hub or machine, including any pre-adjusted system restrictions.
Manufacturer references: Timken Bearing Specification Guide, Order 7534 (2002, archived distributor-hosted copy); Timken MileMate set chart, Order 5523 (May 2024), where listed; Timken cup-and-cone replacement guidance, Order 10832 (2016). Sources checked 2026-10-02. Measurement rows and set identities are kept separate by edition. BearingScope provides independent identification guidance, not sales or installation certification.
L44610 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 2 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKFL 44610/VA983Special single row tapered roller bearing, cup |
| — | — | — | — | 0.039 kg39 g |
| SKFL 44610/VU990Single row tapered roller bearing, cup |
| — | — | — | — | 0.038 kg38 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF L 44610/VA983 | Without | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF L 44610/VU990 | Without | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.