71450 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 71450. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page6 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
TIMKEN 71450 — individual cone dimensions
TIMKEN 71450 is an individual tapered-roller cone: the inner ring, rollers and cage, not the complete cone-and-cup bearing. The manufacturer lists bore d = 114.300 mm (4 1/2 in) and inner-ring width B = 49.213 mm (1.9375 in).
| Measurement | Symbol | Metric | Inches |
|---|---|---|---|
| Bore (d) | d | 114.300 mm | 4 1/2 in |
| Inner Ring Width (B) | B | 49.213 mm | 1.9375 in |
| Effective Center Location | Not specified | -6.6 mm | -0.26 in |
| Shaft Backing Shoulder Diameter - Frontface (da) | da | 125 mm | 4.92 in |
| Shaft Backing Shoulder Diameter - Backface (db) | db | 132 mm | 5.2 in |
| Cage Location rel. to BF (Aa) | Aa | 4.6 mm | 0.18 in |
| Cage Location rel. to FF (Ab) | Ab | 2.5 mm | 0.1 in |
Use the component number correctly
- The bore identifies the shaft-side nominal opening. B measures this cone only; it is not the assembled bearing width T. This single-cone record does not establish an outside diameter D or a matching cup.
- Preserve the full component number and its suffix. A shared prefix, similar ring size or a related-products suggestion does not approve a cone/cup combination or a cross-brand replacement.
- For a complete bearing, check both component markings and the manufacturer’s assembled d×D×T record. B+C is not a valid way to calculate T. A seal, axle rating, vehicle application and tightening procedure need their own evidence.
- Optional measurements with inconsistent printed metric and inch values are omitted from this supplement: Max Shaft Fillet Radius. Verify the manufacturer drawing before using these particular limits.
Factual reference: Timken official individual-component catalogue; source snapshot 2026-10-02. Original interpretation by BearingScope. These measurements do not certify a complete assembly, fit or interchange.
71450 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 22 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| TIMKEN71450 / 71750Tapered roller bearing |
| 364 kN | 543 kN | — | — | 5.15 kg5150 g |
| TIMKEN71450-90041Tapered roller bearing |
| 364 kN | 543 kN | — | — | 5.31 kg5310 g |
| TIMKEN71450-90042Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.77 kg10770 g |
| TIMKEN71450-90045Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90047Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90048Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90049Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90050Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90051Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90053Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90054Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90057Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.91 kg10910 g |
| TIMKEN71450-90059Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.91 kg10910 g |
| TIMKEN71450-90096Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.91 kg10910 g |
| TIMKEN71450-90098Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-90163Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.91 kg10910 g |
| TIMKEN71450-90180Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-902A5Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-902A7Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-902B3Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.97 kg10970 g |
| TIMKEN71450-99415Tapered roller bearing |
| 633 kN | 1090 kN | — | — | 10.77 kg10770 g |
| KOYO71450/750Tapered roller bearing |
| 381 kN | 483 kN | — | 1900 rpmLimiting Speeds(Grease Lub.): 1900 min-1Limiting Speeds(Oil Lub.): 2600 min-1 | 5.05 kg5050 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| TIMKEN 71450 / 71750 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90041 | Open | ABMA Class 0 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90042 | Open | ABMA Class 0 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90045 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90047 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90048 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90049 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90050 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90051 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90053 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90054 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90057 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90059 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90096 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90098 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90163 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-90180 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-902A5 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-902A7 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-902B3 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 71450-99415 | Open | ABMA Class 2 | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 71450/750 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
71450 / 71750
Tapered roller bearing
View full technical record →KOYO71450/750
Tapered roller bearing
View full technical record →TIMKEN71450-90041
Tapered roller bearing
View full technical record →TIMKEN71450-90042
Tapered roller bearing
View full technical record →TIMKEN71450-90045
Tapered roller bearing
View full technical record →TIMKEN71450-90047
Tapered roller bearing
View full technical record →TIMKEN71450-90048
Tapered roller bearing
View full technical record →TIMKEN71450-90049
Tapered roller bearing
View full technical record →TIMKEN71450-90050
Tapered roller bearing
View full technical record →TIMKEN71450-90051
Tapered roller bearing
View full technical record →TIMKEN71450-90053
Tapered roller bearing
View full technical record →TIMKEN71450-90054
Tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.