6300 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6300. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page6 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6300 — published size and closure variants
6300 is the base grouping for the specific records below. Read the complete designation and publisher on each row. The source unit is retained beside the converted unit. A shield or seal can change the width; equal bore and outside diameter do not establish the same envelope.
3 source-labelled records; 3 shown initially.
| Publisher / full model | Closure / material | d×D×B in mm | d×D×B in inches | Source unit |
|---|---|---|---|---|
| SMB6300 | OpenChrome steel | 10× | 0.393701× | mm |
| SMB6300ZZ | ShieldedChrome steel | 10× | 0.393701× | mm |
| SMB6300-2RS | SealedChrome steel | 10× | 0.393701× | mm |
Keep RS, 2RS, ZZ and width suffixes distinct
The table records the publisher’s open, shielded or sealed column. An unlisted “RS” marking is not rewritten as “2RS”. Keep special endings such as W21, W23 or a fractional bore suffix: they can identify a different width or bore. No automatic cross-brand substitution is approved.
Metric values converted from printed inch decimals inherit the source rounding. For example, 0.2812 in converts to 7.14248 mm; that extra decimal detail is arithmetic, not a tolerance or a machining target. Never silently round an inch bearing into the nearest metric size. Missing speed, clearance, precision, internal ball diameter, material grade or exact lubricant remain unknown.
Publisher references: SMB product charts and Enduro 1600-series data; checked 2026-10-02. Original BearingScope interpretation. No stock, sales, vehicle fitment or redistributable CAD is implied. Material names describe the source page, not a certificate for every item sold under a similar number.
6300 dimensions and recorded technical data
The recorded 6300 base designation measures 10×35×11 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, NSK, KOYO, NACHI, NTN. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 55 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6300
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6300-Z — 13 dimension fields
Deep groove ball bearing with seals or shields. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 35 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.009 to 0 mm |
| Width | B | 11 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 17.5 mm |
| Recess diameter | D 2 | ≈ 28.68 mm |
| Chamfer dimension | r 1,2 | min. 0.6 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 14.2 mm |
| Diameter of shaft abutment | d a | max. 17.4 mm |
| Diameter of housing abutment | D a | max. 30.8 mm |
| Radius of shaft or housing fillet | r a | max. 0.6 mm |
SKF 6300 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 35 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.009 to 0 mm |
| Width | B | 11 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 17.5 mm |
| Recess diameter | D 2 | ≈ 28.68 mm |
| Chamfer dimension | r 1,2 | min. 0.6 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 14.2 mm |
| Diameter of housing abutment | D a | max. 30.8 mm |
| Radius of shaft or housing fillet | r a | max. 0.6 mm |
KOYO 6300 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 35 mm |
| Width | B | 11 mm |
KOYO 6300 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 35 mm |
| Width | B | 11 mm |
KOYO 6300 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 35 mm |
| Width | B | 11 mm |
TIMKEN 6300-Z — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 35 mm / 1.378 in |
| Width (B) | B | 11 mm / 0.433 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.6 mm / 0.024 in |
TIMKEN 6300-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 35 mm / 1.378 in |
| Width (B) | B | 11 mm / 0.433 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.6 mm / 0.024 in |
TIMKEN 6300-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 35 mm / 1.378 in |
| Width (B) | B | 11 mm / 0.433 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.6 mm / 0.024 in |
Catalogue parameters for 6300
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 6300 — 49 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 10.0 mm |
| Outside diameter | Not separately recorded | 35.0 mm |
| Width | Not separately recorded | 11.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 8.52 kN |
| Basic static load rating | Not separately recorded | 3.4 kN |
| Reference speed | Not separately recorded | 50000.0 r/min |
| Limiting speed | Not separately recorded | 32000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.19 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.0508 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 35 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.009 to 0 mm |
| Width | B | 11 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 17.5 mm |
| Recess diameter | D 2 | ≈ 28.68 mm |
| Chamfer dimension | r 1,2 | min. 0.6 mm |
| ISO tolerance class for dimensions | Not separately recorded | P6 and tighter width tolerance |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 14.2 mm |
| Diameter of housing abutment | D a | max. 30.8 mm |
| Radius of shaft or housing fillet | r a | max. 0.6 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 8.52 kN |
| Basic static load rating | C 0 | 3.4 kN |
| Fatigue load limit | P u | 0.143 kN |
| Reference speed | Not separately recorded | 50000 r/min |
| Limiting speed | Not separately recorded | 32000 r/min |
| Minimum load factor | k r | 0.03 |
| Calculation factor | f 0 | 11 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 4 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 7 µm |
| Maximum axial run-out of inner ring of assembled bearing | t Sia | 7 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 7 µm |
| Perpendicularity of outer ring outside surface | t SD | 4 µm |
| Maximum axial run-out of outer ring of assembled bearing | t Sea | 8 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
KOYO 6300 — 14 recorded parameters
Deep groove ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 10 mm |
| D | Not separately recorded | 35 mm |
| B | Not separately recorded | 11 mm |
| R(Min.) | Not separately recorded | 0.6 mm |
| Basic Load Ratings : Cr | Not separately recorded | 10.1 kN |
| Basic Load Ratings : C0R | Not separately recorded | 3.45 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 0.270 kN |
| Factor : F0 | Not separately recorded | 11.2 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 22000 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 27000 min-1 |
| Da(Min.) | Not separately recorded | 14 mm |
| Da(Max.) | Not separately recorded | 31 mm |
| Ra(Max.) | Not separately recorded | 0.6 mm |
| Mass(Refer.) | Not separately recorded | 0.053 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6300Deep groove ball bearing |
| 8.52 kN | 3.4 kN | 50000 rpm | 32000 rpm | 0.0508 kg50.8 g |
| TIMKEN6300Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| NSK6300Deep groove ball bearing |
| 8.9 kN | 3.45 kN | — | — | 0.052 kg52 g |
| KOYO6300Deep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 22000 rpmLimiting Speeds(Grease Lub.): 22000 min-1Limiting Speeds(Oil Lub.): 27000 min-1 | 0.053 kg53 g |
| NACHI6300Deep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | 0.053 kg53 g |
| NTN6300Deep groove ball bearing |
| 9.1 kN | 3.5 kN | — | — | 0.053 kg53 g |
| SKF6300-2RSHDeep groove ball bearing with seals |
| 8.52 kN | 3.4 kN | — | 15000 rpm | 0.0529 kg52.9 g |
| SKF6300-2RSH/C3Deep groove ball bearing with seals |
| 8.52 kN | 3.4 kN | — | 15000 rpm | 0.0529 kg52.9 g |
| SKF6300-2RSH/C3GJNDeep groove ball bearings |
| — | — | — | — | 0.0529 kg52.9 g |
| SKF6300 2RSJEMDeep groove ball bearing |
| 8.52 kN | 3.4 kN | — | 15000 rpm | 0.0529 kg52.9 g |
| SKF6300-2ZDeep groove ball bearing with seals or shields |
| 8.52 kN | 3.4 kN | 50000 rpm | 26000 rpm | 0.0535 kg53.5 g |
| SKF6300-2Z/C3Deep groove ball bearing with seals or shields |
| 8.52 kN | 3.4 kN | 50000 rpm | 26000 rpm | 0.054 kg54 g |
| SKF6300 2ZJEMDeep groove ball bearing |
| 8.52 kN | 3.4 kN | 50000 rpm | 26000 rpm | 0.0535 kg53.5 g |
| SKF6300/C3Deep groove ball bearing |
| 8.52 kN | 3.4 kN | 50000 rpm | 32000 rpm | 0.0508 kg50.8 g |
| SKF6300 JEMDeep groove ball bearing |
| 8.52 kN | 3.4 kN | 50000 rpm | 32000 rpm | 0.0508 kg50.8 g |
| SKF6300-ZDeep groove ball bearing with seals or shields |
| 8.52 kN | 3.4 kN | 50000 rpm | 32000 rpm | 0.0524 kg52.4 g |
| FAG6300-BDeep groove ball bearing |
| 8.6 kN | 3.45 kN | 21100 rpm | 31000 rpm | 0.0533 kg53.3 g |
| FAG6300-B-2DRS-L278Deep groove ball bearing |
| 8.6 kN | 3.45 kN | — | 16000 rpm | 0.0539 kg53.9 g |
| FAG6300-B-2DRS-L278-C3Deep groove ball bearing |
| 8.6 kN | 3.45 kN | — | 16000 rpm | 0.0539 kg53.9 g |
| FAG6300-B-2Z-L278Deep groove ball bearing |
| 8.6 kN | 3.45 kN | 21100 rpm | 26500 rpm | 0.0538 kg53.8 g |
| FAG6300-B-2Z-L278-C3Deep groove ball bearing |
| 8.6 kN | 3.45 kN | 21100 rpm | 26500 rpm | 0.0538 kg53.8 g |
| FAG6300-B-C3Deep groove ball bearing |
| 8.6 kN | 3.45 kN | 21100 rpm | 31000 rpm | 0.0533 kg53.3 g |
| FAG6300-H-2RSR-C3>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | — | 13800 rpm | 0.057 kg57 g |
| FAG6300-H-2RSR>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | — | 13800 rpm | 0.057 kg57 g |
| FAG6300-H-2Z-C3>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | 19500 rpm | 26500 rpm | 0.057 kg57 g |
| FAG6300-H-2Z>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | 19500 rpm | 26500 rpm | 0.057 kg57 g |
| FAG6300-H-C3>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | 19500 rpm | 31000 rpm | 0.055 kg55 g |
| FAG6300-H>NDeep groove ball bearing |
| 7.65 kN | 3.47 kN | 19500 rpm | 31000 rpm | 0.055 kg55 g |
| TIMKEN6300-2RSDeep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-2RS-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-2RS-NRDeep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-2RS/VSL609Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-2RZDeep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-2RZ-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-RS-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300/VSL609Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-ZDeep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-Z-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-ZZDeep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| TIMKEN6300-ZZ-C3Deep groove ball bearing |
| 8.24 kN | 3.53 kN | — | — | 0.05 kg50 g |
| NSK6300DDUDeep groove ball bearing |
| 8.9 kN | 3.45 kN | — | — | — |
| NSK6300VVDeep groove ball bearing |
| 8.9 kN | 3.45 kN | — | — | — |
| NSK6300ZZDeep groove ball bearing |
| 8.9 kN | 3.45 kN | — | — | — |
| KOYO6300 2RDDeep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 20000 rpmLimiting Speeds(Grease Lub.): 20000 min-1 | 0.053 kg53 g |
| KOYO6300 2RSDeep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 16000 rpmLimiting Speeds(Grease Lub.): 16000 min-1 | 0.053 kg53 g |
| KOYO6300 2RUDeep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 22000 rpmLimiting Speeds(Grease Lub.): 22000 min-1 | 0.053 kg53 g |
| KOYO6300NRDeep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 22000 rpmLimiting Speeds(Grease Lub.): 22000 min-1Limiting Speeds(Oil Lub.): 27000 min-1 | 0.053 kg53 g |
| KOYO6300 ZZDeep groove ball bearing |
| 10.1 kN | 3.45 kN | — | 22000 rpmLimiting Speeds(Grease Lub.): 22000 min-1 | 0.053 kg53 g |
| NACHI6300-2NKE9Deep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
| NACHI6300-2NSE9Deep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
| NACHI6300NKE9Deep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
| NACHI6300NSE9Deep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
| NACHI6300ZEDeep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
| NACHI6300ZZEDeep groove ball bearing |
| 10.2 kN | 3.45 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6300 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| TIMKEN 6300 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6300 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN 6300 | open | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
| SKF 6300-2RSH | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6300-2RSH/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6300-2RSH/C3GJN | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6300 2RSJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6300-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6300-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6300 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6300/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6300 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6300-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6300-B | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6300-B-2DRS-L278 | 2DRS — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L278 — Grease (L278/customer specific) |
| FAG 6300-B-2DRS-L278-C3 | 2DRS — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L278 — Grease (L278/customer specific) |
| FAG 6300-B-2Z-L278 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L278 — Grease (L278/customer specific) |
| FAG 6300-B-2Z-L278-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L278 — Grease (L278/customer specific) |
| FAG 6300-B-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6300-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6300-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6300-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6300-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6300-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6300-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6300-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-2RS-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6300-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6300DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6300VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6300ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6300 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6300ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6300
Deep groove ball bearing
View full technical record →TIMKEN6300
Deep groove ball bearing
View full technical record →KOYO6300
Deep groove ball bearing
View full technical record →NTN6300
Deep groove ball bearing
View full technical record →NSK6300
Deep groove ball bearing
View full technical record →NACHI6300
Deep groove ball bearing
View full technical record →TIMKEN63000-2RS
Deep groove ball bearing
View full technical record →SKF63000-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF63000-2RS1/W64
Deep groove ball bearing
View full technical record →TIMKEN63000-2RS-C3
Deep groove ball bearing
View full technical record →FAG63000-A-2RSR
Deep groove ball bearing
View full technical record →TIMKEN63001-2RS
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.