Find · understand · compare
6215 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6215. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6215 dimensions and recorded technical data
The recorded 6215 base designation measures 75×130×25 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 108 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6215
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6215/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 75.0 mm |
| Outside diameter | Not supplied separately | 130.0 mm |
| Width | Not supplied separately | 25.0 mm |
SKF 6215 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 130 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.015 to 0 mm |
| Width | B | 25 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 92.05 mm |
| Recess diameter | D 2 | ≈ 116.5 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 84 mm |
| Diameter of housing abutment | D a | max. 121 mm |
| Radius of shaft or housing fillet | r a | max. 1.5 mm |
FAG 6215 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 130 mm |
| Width | B | 25 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 113 mm |
| Caliber diameter outer ring | D2 | 115.5 mm |
| Shoulder diameter inner ring | d1 | 92.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 84 mm |
| Maximum diameter of housing shoulder | Da max | 121 mm |
| Maximum fillet radius | ra max | 1.5 mm |
FAG 6215-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 130 mm |
| Width | B | 25 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 113 mm |
| Caliber diameter outer ring | D2 | 115.5 mm |
| Shoulder diameter inner ring | d1 | 92.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 84 mm |
| Maximum diameter of housing shoulder | Da max | 121 mm |
| Maximum fillet radius | ra max | 1.5 mm |
KOYO 6215 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 130 mm |
| Width | B | 25 mm |
KOYO 6215 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 130 mm |
| Width | B | 25 mm |
KOYO 6215 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 130 mm |
| Width | B | 25 mm |
TIMKEN 6215 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 130 mm / 5.118 in |
| Width (B) | B | 25 mm / 0.984 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6215-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 130 mm / 5.118 in |
| Width (B) | B | 25 mm / 0.984 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6215-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 130 mm / 5.118 in |
| Width (B) | B | 25 mm / 0.984 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6215-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 130 mm / 5.118 in |
| Width (B) | B | 25 mm / 0.984 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6215Deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.16 kg1160 g |
| FAG6215Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.158 kg1158 g |
| TIMKEN6215Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| NSK6215Deep groove ball bearing |
| 73 kN | 49.5 kN | — | — | 1.19 kg1190 g |
| KOYO6215Deep groove ball bearing |
| 84.3 kN | 48.3 kN | — | 4800 rpmLimiting Speeds(Grease Lub.): 4800 min-1Limiting Speeds(Oil Lub.): 5800 min-1 | 1.18 kg1180 g |
| SKF6215-2RS1Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.19 kg1190 g |
| SKF6215-2RS1/C3Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.19 kg1190 g |
| SKF6215-2RS1/HC5C3WTHybrid ceramic deep groove ball bearing with seals on both sides |
| 66.3 kN | 49 kN | — | 3200 rpm | 1.05 kg1050 g |
| SKF6215 2RSJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.2 kg1200 g |
| SKF6215 2RSNRJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.24 kg1240 g |
| SKF6215-2ZDeep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.2 kg1200 g |
| SKF6215-2Z/C3Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.2 kg1200 g |
| SKF6215-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.21 kg1210 g |
| SKF6215-2Z/C4Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.2 kg1200 g |
| SKF6215-2Z/C4VT269Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.2 kg1200 g |
| SKF6215 2ZJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.21 kg1210 g |
| SKF6215 2ZNRJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.22 kg1220 g |
| SKF6215-2Z/VA201Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 49 kN | — | 40 rpm | 1.21 kg1210 g |
| SKF6215-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 49 kN | — | 40 rpm | 1.21 kg1210 g |
| SKF6215-2Z/VA228Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 49 kN | — | 80 rpm | 1.21 kg1210 g |
| SKF6215/AXDDeep groove ball bearing |
| 83.2 kN | 49 kN | 10000 rpm | 6700 rpm | 1.19 kg1190 g |
| SKF6215/C3Deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.16 kg1160 g |
| SKF6215/C3VL0241INSOCOAT® deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.16 kg1160 g |
| SKF6215/C4Deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.16 kg1160 g |
| SKF6215/HC5C3Hybrid ceramic deep groove ball bearing |
| 66.3 kN | 49 kN | 12000 rpm | 8000 rpm | 1.02 kg1020 g |
| SKF6215 JEMDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.16 kg1160 g |
| SKF6215 MDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 9500 rpm | 1.37 kg1370 g |
| SKF6215 M/C3Deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 9500 rpm | 1.38 kg1380 g |
| SKF6215 M/C4VL0241INSOCOAT® deep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 9500 rpm | 1.35 kg1350 g |
| SKF6215 M/HC5C4HS0Hybrid ceramic deep groove ball bearing |
| 66.3 kN | 49 kN | 12000 rpm | 9500 rpm | 1.16 kg1160 g |
| SKF6215 NDeep groove ball bearing with snap ring groove |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.14 kg1140 g |
| SKF6215 NRDeep groove ball bearing with snap ring |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.2 kg1200 g |
| SKF6215 NR/C3Deep groove ball bearing with snap ring |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.2 kg1200 g |
| SKF6215 NRJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.21 kg1210 g |
| SKF6215-RS1Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.17 kg1170 g |
| SKF6215 RSJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | — | 3200 rpm | 1.17 kg1170 g |
| SKF6215/VA201Deep groove ball bearing for high temperature applications |
| — | 49 kN | — | 40 rpm | 1.16 kg1160 g |
| SKF6215-ZDeep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.17 kg1170 g |
| SKF6215-Z/C3Deep groove ball bearing with seals or shields |
| 68.9 kN | 49 kN | 10000 rpm | 5300 rpm | 1.17 kg1170 g |
| SKF6215 ZJEMDeep groove ball bearing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.18 kg1180 g |
| SKF6215-ZNRDeep groove ball bearing with snap ring and integral sealing |
| 68.9 kN | 49 kN | 10000 rpm | 6700 rpm | 1.25 kg1250 g |
| FAG6215-2RSRDeep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.22 kg1220 g |
| FAG6215-2RSR-C2Deep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.22 kg1220 g |
| FAG6215-2RSR-C3Deep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.21 kg1210 g |
| FAG6215-2RSR-C4Deep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.22 kg1220 g |
| FAG6215-2RSR-L140Deep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.183 kg1183 g |
| FAG6215-2ZDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-L069-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-L069-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-L140Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.183 kg1183 g |
| FAG6215-2Z-L140-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.183 kg1183 g |
| FAG6215-2Z-L207-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-2Z-L408-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 6600 rpm | 1.21 kg1210 g |
| FAG6215-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.158 kg1158 g |
| FAG6215-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.158 kg1158 g |
| FAG6215-H-2RSR-SN-C3>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | — | 2850 rpm | 1.18 kg1180 g |
| FAG6215-H-2RSR-SN>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | — | 2850 rpm | 1.18 kg1180 g |
| FAG6215-H-2Z-SN-C3>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | 5800 rpm | 6000 rpm | 1.16 kg1160 g |
| FAG6215-H-2Z-SN>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | 5800 rpm | 6000 rpm | 1.16 kg1160 g |
| FAG6215-H-SN-C3>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | 5800 rpm | 7100 rpm | 1.18 kg1180 g |
| FAG6215-H-SN>NDeep groove ball bearing |
| 60.68 kN | 45.47 kN | 5800 rpm | 7100 rpm | 1.18 kg1180 g |
| FAG6215-J20AADeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.18 kg1180 g |
| FAG6215-J20AA-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.16 kg1160 g |
| FAG6215-J20ABDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.18 kg1180 g |
| FAG6215-J20AB-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.16 kg1160 g |
| FAG6215-J20AB-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.16 kg1160 g |
| FAG6215-J20GA-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.17 kg1170 g |
| FAG6215-MDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.405 kg1405 g |
| FAG6215-M-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.405 kg1405 g |
| FAG6215-M-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.405 kg1405 g |
| FAG6215-M-J20AA-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.34 kg1340 g |
| FAG6215-M-J20GA-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.39 kg1390 g |
| FAG6215-M-J20GC-C4Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 10200 rpm | 1.4 kg1400 g |
| FAG6215-NDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.164 kg1164 g |
| FAG6215-N-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.16 kg1160 g |
| FAG6215-NRDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.187 kg1187 g |
| FAG6215-NR-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.164 kg1164 g |
| FAG6215-RSRDeep groove ball bearing |
| 70 kN | 49 kN | — | 2900 rpm | 1.19 kg1190 g |
| FAG6215-ZDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.152 kg1152 g |
| FAG6215-Z-C3Deep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.152 kg1152 g |
| FAG6215-Z-NDeep groove ball bearing |
| 70 kN | 49 kN | 5900 rpm | 7800 rpm | 1.17 kg1170 g |
| TIMKEN6215-2RSDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-2RS-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-2RS-C3/VSL609Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-2RS/VSL609Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-2RZ-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-C4Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-NRDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-NR-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-RSDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-RS-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215/VSL609Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-ZDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-Z-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-Z-NRDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-Z-NR-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.2 kg1200 g |
| TIMKEN6215-ZZDeep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| TIMKEN6215-ZZ-C3Deep groove ball bearing |
| 66.1 kN | 49.5 kN | — | — | 1.18 kg1180 g |
| NSK6215DDUDeep groove ball bearing |
| 73 kN | 49.5 kN | — | — | — |
| NSK6215VVDeep groove ball bearing |
| 73 kN | 49.5 kN | — | — | — |
| NSK6215ZZDeep groove ball bearing |
| 73 kN | 49.5 kN | — | — | — |
| KOYO6215 2RSDeep groove ball bearing |
| 84.3 kN | 48.3 kN | — | 3100 rpmLimiting Speeds(Grease Lub.): 3100 min-1 | 1.18 kg1180 g |
| KOYO6215 2RUDeep groove ball bearing |
| 84.3 kN | 48.3 kN | — | 4800 rpmLimiting Speeds(Grease Lub.): 4800 min-1 | 1.18 kg1180 g |
| KOYO6215NRDeep groove ball bearing |
| 84.3 kN | 48.3 kN | — | 4800 rpmLimiting Speeds(Grease Lub.): 4800 min-1Limiting Speeds(Oil Lub.): 5800 min-1 | 1.18 kg1180 g |
| KOYO6215 ZZDeep groove ball bearing |
| 84.3 kN | 48.3 kN | — | 4800 rpmLimiting Speeds(Grease Lub.): 4800 min-1 | 1.18 kg1180 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6215 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6215 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6215 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6215 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6215 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6215-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6215-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2RS1/HC5C3WT | Seal on both sides | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | Grease |
| SKF 6215 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6215 2RSNRJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z/C4 | Shield on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z/C4VT269 | Shield on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6215 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6215 2ZNRJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6215-2Z/VA201 | Shield on both sides | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6215-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6215-2Z/VA228 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6215/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6215/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215/C3VL0241 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6215/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6215 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6215 M | Without | P6 and tighter width tolerance | CN | Machined brass | Bearing steel | None |
| SKF 6215 M/C3 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6215 M/C4VL0241 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6215 M/HC5C4HS0 | Without | Not recorded | C4H | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6215 N | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6215 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6215 NR/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215 NRJEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6215 RSJEM | Seal on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215/VA201 | Without | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6215-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6215-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6215 ZJEM | Shield on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6215-ZNR | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| FAG 6215-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2RSR-C2 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2RSR-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6215-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2Z-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6215-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6215-2Z-L069-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6215-2Z-L140 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6215-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6215-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6215-2Z-L408-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L408 — Grease (L408/customer specific) |
| FAG 6215-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-H-2RSR-SN-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6215-H-2RSR-SN>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6215-H-2Z-SN-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6215-H-2Z-SN>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6215-H-SN-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-H-SN>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20AA | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20AB-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-M-J20AA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-M-J20GA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-M-J20GC-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6215-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-N-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-NR-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6215-Z-N | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6215-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-Z-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6215-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6215DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6215VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6215ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6215 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6215 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6215NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6215 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6215
Deep groove ball bearing
View full technical record →FAG6215
Deep groove ball bearing
View full technical record →TIMKEN6215
Deep groove ball bearing
View full technical record →KOYO6215
Deep groove ball bearing
View full technical record →NSK6215
Deep groove ball bearing
View full technical record →TIMKEN6215-2RS
Deep groove ball bearing
View full technical record →KOYO6215 2RS
Deep groove ball bearing
View full technical record →SKF6215-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6215-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →SKF6215-2RS1/HC5C3WT
Hybrid ceramic deep groove ball bearing with seals on both sides
View full technical record →TIMKEN6215-2RS-C3
Deep groove ball bearing
View full technical record →TIMKEN6215-2RS-C3/VSL609
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.