6012 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6012. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6012 dimensions and recorded technical data
The recorded 6012 base designation measures 60×95×18 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 80 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6012
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6012 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 95 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 18 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 71.3 mm |
| Recess diameter | D 2 | ≈ 86.5 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 66 mm |
| Diameter of housing abutment | D a | max. 89 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6012 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 95 mm |
| Width | B | 18 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 83.88 mm |
| Caliber diameter outer ring | D2 | 85.98 mm |
| Shoulder diameter inner ring | d1 | 71.325 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 66 mm |
| Maximum diameter of housing shoulder | Da max | 89 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6012 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 95 mm |
| Width | B | 18 mm |
KOYO 6012 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 95 mm |
| Width | B | 18 mm |
KOYO 6012 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 95 mm |
| Width | B | 18 mm |
TIMKEN 6012-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 60 mm |
| O.D. (D) | D | 95 mm / 3.740 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6012 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 60 mm |
| O.D. (D) | D | 95 mm / 3.740 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6012-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 60 mm |
| O.D. (D) | D | 95 mm / 3.740 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6012-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 60 mm |
| O.D. (D) | D | 95 mm / 3.740 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6012Deep groove ball bearing |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.395 kg395 g |
| FAG6012Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.402 kg402 g |
| TIMKEN6012Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| NSK6012Deep groove ball bearing |
| 32.5 kN | 23.2 kN | — | — | 0.412 kg412 g |
| KOYO6012Deep groove ball bearing |
| 36.8 kN | 23.2 kN | — | 7100 rpmLimiting Speeds(Grease Lub.): 7100 min-1Limiting Speeds(Oil Lub.): 8400 min-1 | 0.415 kg415 g |
| SKF6012-2RS1Deep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | — | 4300 rpm | 0.414 kg414 g |
| SKF6012-2RS1/C3Deep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | — | 4300 rpm | 0.414 kg414 g |
| SKF6012-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 4300 rpm | 0.414 kg414 g |
| SKF6012-2RS1/GJNDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 4300 rpm | 0.414 kg414 g |
| SKF6012 2RSJEMDeep groove ball bearing |
| 30.7 kN | 23.2 kN | — | 4300 rpm | 0.42 kg420 g |
| SKF6012-2RZDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 7500 rpm | 0.414 kg414 g |
| SKF6012-2RZ/HC5C3WTHybrid ceramic deep groove ball bearing with seals on both sides |
| 29.6 kN | 23.2 kN | 16000 rpm | 9000 rpm | 0.383 kg383 g |
| SKF6012-2ZDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 7500 rpm | 0.419 kg419 g |
| SKF6012-2Z/C3Deep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 7500 rpm | 0.419 kg419 g |
| SKF6012-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 7500 rpm | 0.42 kg420 g |
| SKF6012 2ZJEMDeep groove ball bearing |
| 30.7 kN | 23.2 kN | 15000 rpm | 7500 rpm | 0.395 kg395 g |
| SKF6012/AXDDeep groove ball bearing |
| 37.1 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.411 kg411 g |
| SKF6012/C3Deep groove ball bearing |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.395 kg395 g |
| SKF6012 JEMDeep groove ball bearing |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.395 kg395 g |
| SKF6012 M/C4VL0241INSOCOAT® deep groove ball bearing |
| 30.7 kN | 23.2 kN | 15000 rpm | 13000 rpm | 0.473 kg473 g |
| SKF6012 M/HC5C4Hybrid ceramic deep groove ball bearing |
| 29.6 kN | 23.2 kN | 16000 rpm | 13000 rpm | 0.436 kg436 g |
| SKF6012 NRDeep groove ball bearing with snap ring |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.41 kg410 g |
| SKF6012 NR/C4Deep groove ball bearing with snap ring |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.42 kg420 g |
| SKF6012-RS1Deep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | — | 4300 rpm | 0.402 kg402 g |
| SKF6012-ZDeep groove ball bearing with seals or shields |
| 30.7 kN | 23.2 kN | 15000 rpm | 9500 rpm | 0.405 kg405 g |
| FAG6012-2RSRDeep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.419 kg419 g |
| FAG6012-2RSR-C2Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.432 kg432 g |
| FAG6012-2RSR-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.419 kg419 g |
| FAG6012-2RSR-L038Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.419 kg419 g |
| FAG6012-2RSR-L038-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.419 kg419 g |
| FAG6012-2RSR-L138-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.42 kg420 g |
| FAG6012-2RSR-L140Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.432 kg432 g |
| FAG6012-2RSR-L140-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.432 kg432 g |
| FAG6012-2ZDeep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.42 kg420 g |
| FAG6012-2Z-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.42 kg420 g |
| FAG6012-2Z-L038Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.44393 kg443.93 g |
| FAG6012-2Z-L038-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.44393 kg443.93 g |
| FAG6012-2Z-L069-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.43 kg430 g |
| FAG6012-2Z-L138Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.42 kg420 g |
| FAG6012-2Z-L140Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.431 kg431 g |
| FAG6012-2Z-L140-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 8500 rpm | 0.431 kg431 g |
| FAG6012-C2Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.402 kg402 g |
| FAG6012-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.402 kg402 g |
| FAG6012-C4Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.402 kg402 g |
| FAG6012-H-2RSR-SN-C3>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | — | 3800 rpm | 0.386 kg386 g |
| FAG6012-H-2RSR-SN>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | — | 3800 rpm | 0.386 kg386 g |
| FAG6012-H-2Z-SN-C3>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | 7700 rpm | 8600 rpm | 0.381 kg381 g |
| FAG6012-H-2Z-SN>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | 7700 rpm | 8600 rpm | 0.381 kg381 g |
| FAG6012-H-SN-C3>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | 7700 rpm | 10100 rpm | 0.394 kg394 g |
| FAG6012-H-SN>NDeep groove ball bearing |
| 28.02 kN | 21.51 kN | 7700 rpm | 10100 rpm | 0.394 kg394 g |
| FAG6012-MDeep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 13100 rpm | 0.493 kg493 g |
| FAG6012-M-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 13100 rpm | 0.51272 kg512.72 g |
| FAG6012-NRDeep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.412 kg412 g |
| FAG6012-RSRDeep groove ball bearing |
| 31.5 kN | 23.2 kN | — | 3750 rpm | 0.4536 kg453.6 g |
| FAG6012-ZDeep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.44393 kg443.93 g |
| FAG6012-Z-C3Deep groove ball bearing |
| 31.5 kN | 23.2 kN | 7600 rpm | 10100 rpm | 0.44393 kg443.93 g |
| TIMKEN6012-2RSDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-2RS-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-2RS-C3/VSL609Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-2RS/VSL609Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-2RZDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012-2RZ-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012-2RZ-NR-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-NRDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-RSDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-RS-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012/VSL609Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-ZDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-Z-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012-Z-NRDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6012-ZZDeep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| TIMKEN6012-ZZ-C3Deep groove ball bearing |
| 29.4 kN | 23.2 kN | — | — | 0.41 kg410 g |
| NSK6012DDUDeep groove ball bearing |
| 32.5 kN | 23.2 kN | — | — | — |
| NSK6012VVDeep groove ball bearing |
| 32.5 kN | 23.2 kN | — | — | — |
| NSK6012ZZDeep groove ball bearing |
| 32.5 kN | 23.2 kN | — | — | — |
| KOYO6012 2RSDeep groove ball bearing |
| 36.8 kN | 23.2 kN | — | 4000 rpmLimiting Speeds(Grease Lub.): 4000 min-1 | 0.415 kg415 g |
| KOYO6012 2RUDeep groove ball bearing |
| 36.8 kN | 23.2 kN | — | 7100 rpmLimiting Speeds(Grease Lub.): 7100 min-1 | 0.415 kg415 g |
| KOYO6012NRDeep groove ball bearing |
| 36.8 kN | 23.2 kN | — | 7100 rpmLimiting Speeds(Grease Lub.): 7100 min-1Limiting Speeds(Oil Lub.): 8400 min-1 | 0.415 kg415 g |
| KOYO6012 ZZDeep groove ball bearing |
| 36.8 kN | 23.2 kN | — | 7100 rpmLimiting Speeds(Grease Lub.): 7100 min-1 | 0.415 kg415 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6012 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6012 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6012 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6012 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6012 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6012-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6012-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6012-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6012-2RS1/GJN | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6012 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6012-2RZ | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6012-2RZ/HC5C3WT | Seal on both sides | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | Grease |
| SKF 6012-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6012-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6012-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6012 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6012/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6012/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6012 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6012 M/C4VL0241 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6012 M/HC5C4 | Without | Not recorded | C4 | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6012 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6012 NR/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6012-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6012-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6012-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6012-2RSR-C2 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6012-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6012-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6012-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6012-2RSR-L138-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6012-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6012-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6012-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6012-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6012-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6012-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6012-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6012-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6012-2Z-L140 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6012-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6012-C2 | Without — Not sealed | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-H-2RSR-SN-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6012-H-2RSR-SN>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6012-H-2Z-SN-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6012-H-2Z-SN>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6012-H-SN-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-H-SN>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6012-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6012-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6012-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6012-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-2RZ-NR-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6012-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6012DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6012VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6012ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6012 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6012 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6012NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6012 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6012
Deep groove ball bearing
View full technical record →FAG6012
Deep groove ball bearing
View full technical record →TIMKEN6012
Deep groove ball bearing
View full technical record →KOYO6012
Deep groove ball bearing
View full technical record →NSK6012
Deep groove ball bearing
View full technical record →TIMKEN6012-2RS
Deep groove ball bearing
View full technical record →KOYO6012 2RS
Deep groove ball bearing
View full technical record →SKF6012-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6012-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →SKF6012-2RS1/C3GJN
Deep groove ball bearing with seals or shields
View full technical record →SKF6012-2RS1/GJN
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6012-2RS-C3
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.