6000 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6000. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page7 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6000 — published size and closure variants
6000 is the base grouping for the specific records below. Read the complete designation and publisher on each row. The source unit is retained beside the converted unit. A shield or seal can change the width; equal bore and outside diameter do not establish the same envelope.
3 source-labelled records; 3 shown initially.
| Publisher / full model | Closure / material | d×D×B in mm | d×D×B in inches | Source unit |
|---|---|---|---|---|
| SMB6000 | OpenChrome steel | 10× | 0.393701× | mm |
| SMB6000ZZ | ShieldedChrome steel | 10× | 0.393701× | mm |
| SMB6000-2RS | SealedChrome steel | 10× | 0.393701× | mm |
Keep RS, 2RS, ZZ and width suffixes distinct
The table records the publisher’s open, shielded or sealed column. An unlisted “RS” marking is not rewritten as “2RS”. Keep special endings such as W21, W23 or a fractional bore suffix: they can identify a different width or bore. No automatic cross-brand substitution is approved.
Metric values converted from printed inch decimals inherit the source rounding. For example, 0.2812 in converts to 7.14248 mm; that extra decimal detail is arithmetic, not a tolerance or a machining target. Never silently round an inch bearing into the nearest metric size. Missing speed, clearance, precision, internal ball diameter, material grade or exact lubricant remain unknown.
Publisher references: SMB product charts and Enduro 1600-series data; checked 2026-10-02. Original BearingScope interpretation. No stock, sales, vehicle fitment or redistributable CAD is implied. Material names describe the source page, not a certificate for every item sold under a similar number.
6000 — source-labelled NSK dimensions
Nominal dimensions from the NSK Bearing Replacement Guide, reference BRG/C/E/11.15. This is a historical catalogue reference, checked 2026-10-03; it is not a current product-availability list or an interchange approval. Each row preserves its complete printed designation.
| Complete NSK designation | Bore d | Outside D | Width B | Source page / boundary |
|---|---|---|---|---|
| NSK catalogue record6000 | 10 mm | 26 mm | 8 mm | Printed p. 29Nominal envelope only; complete execution as marked |
| NSK catalogue record6000D | 10 mm | 26 mm | 8 mm | Printed p. 29Nominal envelope only; complete execution as marked |
| NSK catalogue record6000DDU | 10 mm | 26 mm | 8 mm | Printed p. 29Nominal envelope only; complete execution as marked |
| NSK catalogue record6000VV | 10 mm | 26 mm | 8 mm | Printed p. 29Nominal envelope only; complete execution as marked |
| NSK catalogue record6000Z | 10 mm | 26 mm | 8 mm | Printed p. 30Nominal envelope only; complete execution as marked |
| NSK catalogue record6000ZZ | 10 mm | 26 mm | 8 mm | Printed p. 30Nominal envelope only; complete execution as marked |
| NSK catalogue record6000ZZNR | 10 mm | 26 mm | 8 mm | Printed p. 30Nominal envelope only; complete execution as marked |
Read d×D×B together. Equal outside dimensions do not prove equal seals, internal clearance, precision, load ratings, lubricant or speed limits. Those properties are not supplied by this dimensional table. A DU, DDU, Z, ZZ, VV, DD or other marking is kept as printed; missing suffix records are not created from a base model.
6000 dimensions and recorded technical data
The recorded 6000 base designation measures 10×26×8 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, NSK, KOYO, NACHI. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 103 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6000
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6000/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 10.0 mm |
| Outside diameter | Not supplied separately | 26.0 mm |
| Width | Not supplied separately | 8.0 mm |
SKF 6000 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 26 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.008 to 0 mm |
| Width | B | 8 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 14.8 mm |
| Recess diameter | D 2 | ≈ 22.6 mm |
| Chamfer dimension | r 1,2 | min. 0.3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 12 mm |
| Diameter of housing abutment | D a | max. 24 mm |
| Radius of shaft or housing fillet | r a | max. 0.3 mm |
KOYO 6000 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 26 mm |
| Width | B | 8 mm |
KOYO 6000 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 26 mm |
| Width | B | 8 mm |
TIMKEN 6000-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 26 mm / 1.024 in |
| Width (B) | B | 8 mm / 0.315 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.3 mm / 0.012 in |
TIMKEN 6000-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 26 mm / 1.024 in |
| Width (B) | B | 8 mm / 0.315 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.3 mm / 0.012 in |
TIMKEN 6000-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 26 mm / 1.024 in |
| Width (B) | B | 8 mm / 0.315 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.3 mm / 0.012 in |
TIMKEN 6000 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 10 mm |
| O.D. (D) | D | 26 mm / 1.024 in |
| Width (B) | B | 8 mm / 0.315 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 0.3 mm / 0.012 in |
Catalogue parameters for 6000
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 6000 — 49 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 10.0 mm |
| Outside diameter | Not separately recorded | 26.0 mm |
| Width | Not separately recorded | 8.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 4.75 kN |
| Basic static load rating | Not separately recorded | 1.96 kN |
| Reference speed | Not separately recorded | 67000.0 r/min |
| Limiting speed | Not separately recorded | 40000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.07 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.0178 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 26 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.008 to 0 mm |
| Width | B | 8 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 14.8 mm |
| Recess diameter | D 2 | ≈ 22.6 mm |
| Chamfer dimension | r 1,2 | min. 0.3 mm |
| ISO tolerance class for dimensions | Not separately recorded | P6 and tighter width tolerance |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 12 mm |
| Diameter of housing abutment | D a | max. 24 mm |
| Radius of shaft or housing fillet | r a | max. 0.3 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 4.75 kN |
| Basic static load rating | C 0 | 1.96 kN |
| Fatigue load limit | P u | 0.083 kN |
| Reference speed | Not separately recorded | 67000 r/min |
| Limiting speed | Not separately recorded | 40000 r/min |
| Minimum load factor | k r | 0.03 |
| Calculation factor | f 0 | 12 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 4 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 7 µm |
| Maximum axial run-out of inner ring of assembled bearing | t Sia | 7 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 6 µm |
| Perpendicularity of outer ring outside surface | t SD | 4 µm |
| Maximum axial run-out of outer ring of assembled bearing | t Sea | 8 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
KOYO 6000 — 14 recorded parameters
Deep groove ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
The plain KOYO 6000 record is open. For a sealed candidate, inspect the separate KOYO 6000 2RS record; for a shielded candidate, inspect KOYO 6000 ZZ. Both are listed in this page’s exact-designation references with their own parameters. The base number alone does not specify a closure.
These are distinct catalogue constructions, not a suggestion to add a loose seal to an open bearing. Seal replacement or removal requires the original assembly information; no loose-seal part number or equipment fitment is established by these records.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 10 mm |
| D | Not separately recorded | 26 mm |
| B | Not separately recorded | 8 mm |
| R(Min.) | Not separately recorded | 0.3 mm |
| Basic Load Ratings : Cr | Not separately recorded | 5.70 kN |
| Basic Load Ratings : C0R | Not separately recorded | 1.95 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 0.100 kN |
| Factor : F0 | Not separately recorded | 12.3 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 31000 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 36000 min-1 |
| Da(Min.) | Not separately recorded | 12 mm |
| Da(Max.) | Not separately recorded | 24 mm |
| Ra(Max.) | Not separately recorded | 0.3 mm |
| Mass(Refer.) | Not separately recorded | 0.019 kg |
NTN 6000LU — 20 recorded parameters
Single row deep groove ball bearings
Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.
For this exact NTN 6000LU record, the nominal envelope is 10×26×8 mm (d = internal diameter; D = external diameter; B = bearing/inner ring width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 0.393701×1.023622×0.314961 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6000LU: contact seal on one side. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Dimensions and properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Internal diameter | d | 10 mm |
| External diameter | D | 26 mm |
| Bearing/Inner ring width | B | 8 mm |
| Min fillet radius | rs | 0.3 mm |
| Radial clearance class | Not separately recorded | CN |
| Mass | Not separately recorded | 0.019 kg |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dynamic load | C | 5.05 kN |
| Static load | C0 | 1.96 kN |
| Fatigue limit load | Cu | 0.138 kN |
| Coefficient | f0 | 12.4 |
| Grease lubrication limit speed | N lim | 21000 r/min |
| Min operating temperature | Tmin | -25 °C |
| Max operating temperature | Tmax | 110 °C |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Min shoulder diameter IR | da min | 12 mm |
| Max shoulder diameter IR | da max | 13.5 mm |
| Max shoulder diameter OR | Da max | 24 mm |
| Max shaft & housing fillet radius | ra max | 0.3 mm |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue construction | Not separately recorded | Deep groove ball bearing, radial contact, pressed steel cage, contact seal on one side |
| Cage construction | Not separately recorded | pressed steel cage |
| Closure construction | Not separately recorded | contact seal on one side |
NSK 6000 — 15 recorded parameters
Single row deep groove ball bearings
Reference: NSK Rolling Bearings catalogue E1103c, Part C; source snapshot 2026-10-02.
For this exact NSK 6000 record, the nominal envelope is 10×26×8 mm (d = bore diameter; D = outside diameter; B = bearing width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 0.393701×1.023622×0.314961 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6000: Open. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Boundary dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 26 mm |
| Bearing width | B | 8 mm |
| Minimum bearing chamfer | r min. | 0.3 mm |
Load ratings
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic radial load rating | Cr | 5050 N |
| Basic static radial load rating | C0r | 1970 N |
| Equivalent-load calculation factor | f0 | 12.4 |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum shaft shoulder diameter | da min. | 12 mm |
| Maximum shaft shoulder diameter | da max. | 13 mm |
| Maximum housing shoulder diameter | Da max. | 24 mm |
| Maximum shaft or housing fillet radius | ra max. | 0.3 mm |
Lubrication-qualified speed
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting speed with grease | Not separately recorded | 30000 r/min |
| Limiting speed with oil (open bearing) | Not separately recorded | 36000 r/min |
Reference mass
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Approximate catalogue mass (open reference) | Not separately recorded | 0.018 kg |
Construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue closure construction | Not separately recorded | Open |
NACHI 6000 — 15 recorded parameters
Deep groove ball bearing
Reference: NACHI Deep Groove Ball Bearings catalogue B3402E-2; source snapshot 2026-10-02.
For this exact NACHI 6000 record, the nominal envelope is 10×26×8 mm (d = bore diameter; D = outside diameter; B = bearing width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 0.393701×1.023622×0.314961 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6000: Open. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Boundary dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 10 mm |
| Outside diameter | D | 26 mm |
| Bearing width | B | 8 mm |
| Minimum bearing chamfer | r min. | 0.3 mm |
Load ratings
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic radial load rating | Cr | 5750 N |
| Basic static radial load rating | C0r | 1970 N |
Equivalent-load factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue load calculation factor | f0 | 12.4 |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum shaft shoulder diameter | da min. | 12 mm |
| Maximum housing shoulder diameter | Da max. | 24 mm |
| Maximum adjacent fillet radius | ra max. | 0.3 mm |
Construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Closure arrangement | Not separately recorded | Open |
| Listed closure suffix | Not separately recorded | None (open type) |
Reference mass
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue row mass (variants not individually specified) | Not separately recorded | 0.019 kg |
Lubrication-qualified speed
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting speed with grease (open) | Not separately recorded | 30000 r/min |
| Limiting speed with oil (open) | Not separately recorded | 36000 r/min |
KOYO 6000 2RS — 16 recorded parameters
Deep groove ball bearing
Reference: JTEKT / KOYO public product catalogue; source snapshot 2026-09-02.
Looking for a 6000 sealed bearing? KOYO 6000 2RS is a recorded catalogue candidate with contact seals on both sides. Its recorded nominal size is 10×26×8 mm, in the order bore d × outside diameter D × width B.
In JTEKT / KOYO Table 6-2, 2RS identifies contact seals on both sides. The corresponding one-sided code is RS. This manufacturer-specific explanation is consistent with the classification of this exact product record; it does not turn every 6000 base record into a sealed or shielded version.
Select the full marking, not the base number alone. Compare the grease-qualified speed, clearance, material and mounting dimensions of the candidate record before using it. A closure designation does not supply a waterproof rating, chemical-resistance certificate or approved replacement relationship.
The original product parameters below retain their source units. An absent or dash-valued oil speed is unknown, not zero and not permission to use the grease speed for an oil-lubricated arrangement.
Classification
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Official Category Path | Not separately recorded | Deep groove ball bearings - Single-row - Shielded/sealed type - Contact sealed |
| Official Classification 1 | Not separately recorded | Deep groove ball bearings / Single-row / Shielded/sealed type / Contact sealed |
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 10 mm |
| D | Not separately recorded | 26 mm |
| B | Not separately recorded | 8 mm |
| R(Min.) | Not separately recorded | 0.3 mm |
| Basic Load Ratings : Cr | Not separately recorded | 5.70 kN |
| Basic Load Ratings : C0R | Not separately recorded | 1.95 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 0.100 kN |
| Factor : F0 | Not separately recorded | 12.3 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 19000 min-1 |
| Da(Min.) | Not separately recorded | 12 mm |
| Da(Max.) | Not separately recorded | 13 mm |
| Da(Max.) | Not separately recorded | 24 mm |
| Ra(Max.) | Not separately recorded | 0.3 mm |
| Mass(Refer.) | Not separately recorded | 0.019 kg |
KOYO 6000 ZZ — 16 recorded parameters
Deep groove ball bearing
Reference: JTEKT / KOYO public product catalogue; source snapshot 2026-09-02.
Looking for a 6000 shielded bearing? KOYO 6000 ZZ is a recorded catalogue candidate with fixed shields on both sides. Its recorded nominal size is 10×26×8 mm, in the order bore d × outside diameter D × width B.
In JTEKT / KOYO Table 6-2, ZZ identifies fixed shields on both sides. The corresponding one-sided code is Z. This manufacturer-specific explanation is consistent with the classification of this exact product record; it does not turn every 6000 base record into a sealed or shielded version.
Select the full marking, not the base number alone. Compare the grease-qualified speed, clearance, material and mounting dimensions of the candidate record before using it. A closure designation does not supply a waterproof rating, chemical-resistance certificate or approved replacement relationship.
The original product parameters below retain their source units. An absent or dash-valued oil speed is unknown, not zero and not permission to use the grease speed for an oil-lubricated arrangement.
Classification
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Official Category Path | Not separately recorded | Deep groove ball bearings - Single-row - Shielded/sealed type - Shielded ZZ |
| Official Classification 1 | Not separately recorded | Deep groove ball bearings / Single-row / Shielded/sealed type / Shielded ZZ |
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 10 mm |
| D | Not separately recorded | 26 mm |
| B | Not separately recorded | 8 mm |
| R(Min.) | Not separately recorded | 0.3 mm |
| Basic Load Ratings : Cr | Not separately recorded | 5.70 kN |
| Basic Load Ratings : C0R | Not separately recorded | 1.95 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 0.100 kN |
| Factor : F0 | Not separately recorded | 12.3 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 31000 min-1 |
| Da(Min.) | Not separately recorded | 12 mm |
| Da(Max.) | Not separately recorded | 13 mm |
| Da(Max.) | Not separately recorded | 24 mm |
| Ra(Max.) | Not separately recorded | 0.3 mm |
| Mass(Refer.) | Not separately recorded | 0.019 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6000Deep groove ball bearing |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0178 kg17.8 g |
| TIMKEN6000Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| NSK6000Deep groove ball bearing |
| 5.05 kN | 1.97 kN | — | — | 0.018 kg18 g |
| KOYO6000Deep groove ball bearing |
| 5.7 kN | 1.95 kN | — | 31000 rpmLimiting Speeds(Grease Lub.): 31000 min-1Limiting Speeds(Oil Lub.): 36000 min-1 | 0.019 kg19 g |
| NACHI6000Deep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | 0.019 kg19 g |
| SKF6000-2RSHDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | — | 19000 rpm | 0.019 kg19 g |
| SKF6000-2RSH/C3Deep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | 67000 rpm | 19000 rpm | 0.019 kg19 g |
| SKF6000-2RSH/C3GJNDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | — | — | 0.0185 kg18.5 g |
| SKF6000-2RSH/GFJDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | — | 19000 rpm | 0.0185 kg18.5 g |
| SKF6000-2RSH/VA947SKF Food line deep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | — | 19000 rpm | 0.0191 kg19.1 g |
| SKF6000 2RSJEMDeep groove ball bearing |
| 4.75 kN | 1.96 kN | — | 19000 rpm | 0.0189 kg18.9 g |
| SKF6000-2RSLDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0184 kg18.4 g |
| SKF6000-2RSL/C3Deep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0184 kg18.4 g |
| SKF6000-2RSLTN9/C3VT162Deep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0178 kg17.8 g |
| SKF6000-2RSLTN9/HC5C3WTHybrid ceramic deep groove ball bearing with low-friction seals on both sides |
| 4.62 kN | 1.96 kN | 70000 rpm | 34000 rpm | 0.0153 kg15.3 g |
| SKF6000-2ZDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0194 kg19.4 g |
| SKF6000-2Z/C3Deep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0194 kg19.4 g |
| SKF6000-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0192 kg19.2 g |
| SKF6000-2Z/C3VT127Deep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0195 kg19.5 g |
| SKF6000 2ZJEMDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0192 kg19.2 g |
| SKF6000-2Z/LHT23Deep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 34000 rpm | 0.0192 kg19.2 g |
| SKF6000-2ZTN9/C3LTDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | — | — | 0.0186 kg18.6 g |
| SKF6000/C3Deep groove ball bearing |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0178 kg17.8 g |
| SKF6000 JEMDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0178 kg17.8 g |
| SKF6000-RSHDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | — | 19000 rpm | 0.0177 kg17.7 g |
| SKF6000-RSLDeep groove ball bearing with seals |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0177 kg17.7 g |
| SKF6000-ZDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0185 kg18.5 g |
| SKF6000-Z/C3Deep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0185 kg18.5 g |
| SKF6000 ZJEMDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0185 kg18.5 g |
| SKF6000-ZTN9Deep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | — | — | 0.0179 kg17.9 g |
| SKF6000-ZTN9/C3LTDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | — | — | 0.0179 kg17.9 g |
| SKF6000-ZTN9/LTDeep groove ball bearing with seals or shields |
| 4.75 kN | 1.96 kN | 67000 rpm | 40000 rpm | 0.0179 kg17.9 g |
| FAG6000-C-2BRS-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2BRS-TVH-L178-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.017 kg17 g |
| FAG6000-C-2BRS>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-L038-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-L038>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-L138-CM>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-L138>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2HRS-TVH-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.017 kg17 g |
| FAG6000-C-2HRS>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-2Z-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2Z-L038-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2Z-L038>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.019 kg19 g |
| FAG6000-C-2Z-L069-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2Z-L138-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.019 kg19 g |
| FAG6000-C-2Z-L138-CM>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.019 kg19 g |
| FAG6000-C-2Z-L207>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-2Z>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 38000 rpm | 0.018 kg18 g |
| FAG6000-C-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 44500 rpm | 0.017 kg17 g |
| FAG6000-C-HRS>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C-HRS-Z-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | — | 28500 rpm | 0.018 kg18 g |
| FAG6000-C>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 44500 rpm | 0.017 kg17 g |
| FAG6000-C-Z-C3>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 44500 rpm | 0.018 kg18 g |
| FAG6000-C-Z-TVH>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 44500 rpm | 0.017 kg17 g |
| FAG6000-C-Z>VDeep groove ball bearing |
| 5.3 kN | 1.97 kN | 30000 rpm | 44500 rpm | 0.018 kg18 g |
| FAG6000-H-2RSR-C3>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | — | 18200 rpm | 0.018 kg18 g |
| FAG6000-H-2RSR>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | — | 18200 rpm | 0.018 kg18 g |
| FAG6000-H-2Z-C3>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 27500 rpm | 34500 rpm | 0.019 kg19 g |
| FAG6000-H-2Z>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 27500 rpm | 34500 rpm | 0.019 kg19 g |
| FAG6000-H-C3>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 27500 rpm | 40500 rpm | 0.018 kg18 g |
| FAG6000-H>NDeep groove ball bearing |
| 4.75 kN | 1.96 kN | 27500 rpm | 40500 rpm | 0.018 kg18 g |
| TIMKEN6000-2RSDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RS-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RS-C3/VSL609Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RS-NRDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RS/VSL609Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RZDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RZ-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-2RZ-NR-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000HDeep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000H-2RSDeep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000H-2RS/FVSL613Deep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000H-2RS/VSL609Deep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000H/FVSL527Deep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000H/FVSL613Deep groove ball bearing |
| 3.89 kN | 1.58 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-RSDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-RS-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000TN1-ZDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000/VSL609Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-ZDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-Z-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-ZZDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-ZZ-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-ZZ-NRDeep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| TIMKEN6000-ZZ-NR-C3Deep groove ball bearing |
| 4.58 kN | 1.97 kN | — | — | 0.02 kg20 g |
| NSK6000DDUDeep groove ball bearing |
| 5.05 kN | 1.97 kN | — | — | — |
| NSK6000VVDeep groove ball bearing |
| 5.05 kN | 1.97 kN | — | — | — |
| NSK6000ZZDeep groove ball bearing |
| 5.05 kN | 1.97 kN | — | — | — |
| KOYO6000 2RDDeep groove ball bearing |
| 5.7 kN | 1.95 kN | — | 28000 rpmLimiting Speeds(Grease Lub.): 28000 min-1 | 0.019 kg19 g |
| KOYO6000 2RSDeep groove ball bearing |
| 5.7 kN | 1.95 kN | — | 19000 rpmLimiting Speeds(Grease Lub.): 19000 min-1 | 0.019 kg19 g |
| KOYO6000 2RUDeep groove ball bearing |
| 5.7 kN | 1.95 kN | — | 31000 rpmLimiting Speeds(Grease Lub.): 31000 min-1 | 0.019 kg19 g |
| KOYO6000 ZZDeep groove ball bearing |
| 5.7 kN | 1.95 kN | — | 31000 rpmLimiting Speeds(Grease Lub.): 31000 min-1 | 0.019 kg19 g |
| NACHI6000-2NKE9Deep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NACHI6000-2NSE9Deep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NACHI6000NKE9Deep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NACHI6000NSE9Deep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NACHI6000ZEDeep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NACHI6000ZZEDeep groove ball bearing |
| 5.75 kN | 1.97 kN | — | — | — |
| NTN6000LUDeep groove ball bearing |
| 5.05 kN | 1.96 kN | — | — | 0.019 kg19 g |
| NTN6000ZDeep groove ball bearing |
| 5.05 kN | 1.96 kN | — | — | 0.019 kg19 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6000 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| TIMKEN 6000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6000 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6000 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6000-2RSH | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSH/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSH/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSH/GFJ | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSH/VA947 | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Food grade grease |
| SKF 6000 2RSJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSL | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSL/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2RSLTN9/C3VT162 | Seal on both sides | Not recorded | C3 | Non-metallic | Bearing steel | Grease |
| SKF 6000-2RSLTN9/HC5C3WT | Seal on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6000-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6000-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2Z/C3VT127 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6000-2Z/LHT23 | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6000-2ZTN9/C3LT | Shield on both sides | Not recorded | C3 | Non-metallic | Bearing steel | Grease |
| SKF 6000/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6000 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6000-RSH | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6000-RSL | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6000-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6000-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6000 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6000-ZTN9 | Shield on one side | Not recorded | CN | Non-metallic | Bearing steel | Grease |
| SKF 6000-ZTN9/C3LT | Shield on one side | Not recorded | C3 | Non-metallic | Bearing steel | Grease |
| SKF 6000-ZTN9/LT | Shield on one side | Not recorded | CN | Non-metallic | Bearing steel | Grease |
| FAG 6000-C-2BRS-C3>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2BRS-TVH-L178-C3>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | L178 — Grease (L178/customer specific) |
| FAG 6000-C-2BRS>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2HRS-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2HRS-L038-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6000-C-2HRS-L038>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6000-C-2HRS-L138-CM>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CM (Group M) — Internal clearance limited for electric motors | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6000-C-2HRS-L138>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6000-C-2HRS-TVH-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2HRS>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2Z-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-2Z-L038-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6000-C-2Z-L038>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6000-C-2Z-L069-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6000-C-2Z-L138-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6000-C-2Z-L138-CM>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CM (Group M) — Internal clearance limited for electric motors | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6000-C-2Z-L207>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6000-C-2Z>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-C-HRS>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-C-HRS-Z-C3>V | Z-HRS — Non-contact shield on one Side, Contact seal on the other side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA14 — Ball bearing grease, low noise |
| FAG 6000-C>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-C-Z-C3>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-C-Z-TVH>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | Without — Bearing not greased |
| FAG 6000-C-Z>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6000-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6000-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6000-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6000-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6000-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6000-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RS-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-2RZ-NR-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H-2RS | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H-2RS/FVSL613 | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H-2RS/VSL609 | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H/FVSL527 | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000H/FVSL613 | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000TN1-Z | Shielded | Not recorded | Not recorded | Nylon cage | Not recorded | Not recorded |
| TIMKEN 6000/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-ZZ-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6000-ZZ-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6000DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6000VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6000ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6000 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6000 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6000 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6000 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6000ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN 6000LU | contact seal on one side | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
| NTN 6000Z | shield on one side | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6000
Deep groove ball bearing
View full technical record →TIMKEN6000
Deep groove ball bearing
View full technical record →KOYO6000
Deep groove ball bearing
View full technical record →NSK6000
Deep groove ball bearing
View full technical record →NACHI6000
Deep groove ball bearing
View full technical record →NACHI6000-2NKE9
Deep groove ball bearing
View full technical record →NACHI6000-2NSE9
Deep groove ball bearing
View full technical record →KOYO6000 2RD
Deep groove ball bearing
View full technical record →TIMKEN6000-2RS
Deep groove ball bearing
View full technical record →KOYO6000 2RS
Deep groove ball bearing
View full technical record →TIMKEN6000-2RS-C3
Deep groove ball bearing
View full technical record →TIMKEN6000-2RS-C3/VSL609
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.