592 A bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 592 A. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page6 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
TIMKEN 592A — bearing pairs and set identification
For TIMKEN 592A, the component number alone does not establish every dimension of a complete bearing. This reference identifies documented cone/cup combinations that contain 592A; select the row matching both of your component markings.
Which components make up the set?
| TIMKEN set | Cone | Cup | Reference / package scope |
|---|---|---|---|
| SET403 | 594A | 592A | 2024-05 · manual-adjustment |
| SET404 | 598A | 592A | 2024-05 · manual-adjustment |
Complete bearing dimensions by exact pair
These TS single-row tapered-roller combinations are reproduced as factual measurements from the 2002 reference. Dimensions are not a fitment approval or a current availability claim. Each cell keeps both published units.
| Cone / cup | Bore d | Outside D | Assembly T |
|---|---|---|---|
| 590A / 592A | 76.200 mm 3.000 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 595 / 592A | 82.550 mm 3.250 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 596 / 592A | 85.725 mm 3.375 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 593 / 592A | 88.900 mm 3.500 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 593A / 592A | 88.900 mm 3.500 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 598 / 592A | 92.075 mm 3.625 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 598A / 592A | 92.075 mm 3.625 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 594 / 592A | 95.250 mm 3.750 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
| 594A / 592A | 95.250 mm 3.750 in | 152.400 mm 6.000 in | 39.688 mm 1.563 in |
Separate ring widths B / C and source page references
B and C below describe separate components. Their sum is not the assembly width T.
| Cone / cup | Cone width B | Cup width C | 2002 PDF pages |
|---|---|---|---|
| 590A / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 269, 322 |
| 595 / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 274, 323 |
| 596 / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 277, 323 |
| 593 / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 278, 322 |
| 593A / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 278, 322 |
| 598 / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 280, 323 |
| 598A / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 280, 323 |
| 594 / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 281, 322 |
| 594A / 592A | 36.322 mm 1.430 in | 30.162 mm 1.188 in | 282, 322 |
What to confirm before using this reference
- d is the cone bore, D is the cup outside diameter and T is the complete bearing width for the exact pair. B and C measure the separate rings; do not add B and C to calculate T.
- The dimensional table is a historical identification reference from the 2002 Timken Bearing Specification Guide, not a current engineering drawing. Printed metric and inch values are retained, including their original rounding. Check the current drawing before specifying fits or machining.
- A component may appear with several mating numbers. A match here documents that exact Timken combination; it does not approve other suffixes, mixed-brand rings, a vehicle application or a substitute with similar dimensions.
- A cone-and-cup set is not automatically a complete wheel-end repair kit. Seal numbers, collars, spacers and quantities must be confirmed separately unless the specific set note below explicitly lists them.
- For replacement work, inspect and replace the mating cup and cone together as specified for the assembly. Retaining a worn ring or mixing manufacturer geometries can change the contact pattern even when nominal diameters match.
- An axle tightening torque, preload or endplay target cannot be derived from these dimensions. Use the procedure for the identified hub or machine, including any pre-adjusted system restrictions.
Manufacturer references: Timken Bearing Specification Guide, Order 7534 (2002, archived distributor-hosted copy); Timken MileMate set chart, Order 5523 (May 2024), where listed; Timken cup-and-cone replacement guidance, Order 10832 (2016). Sources checked 2026-10-02. Measurement rows and set identities are kept separate by edition. BearingScope provides independent identification guidance, not sales or installation certification.
592 A dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 3 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 592 A
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 592 A — 13 recorded parameters
Single row tapered roller bearing, cup
Reference: SKF product catalogue; source snapshot 2026-09-02.
This designation identifies a tapered-bearing component. A cone or cup alone is not the assembled bearing; use the documented pairing and total assembly width before comparing an interchange.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Outside diameter | Not separately recorded | 152.4 mm |
| Width, total | Not separately recorded | 30.162 mm |
| Width, outer ring | Not separately recorded | 30.162 mm |
| Contact angle | Not separately recorded | 16.4 ° |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Outer ring (cup) |
| Arrangement of contact angle (double-row bearing) | Not separately recorded | Not applicable |
| Matched arrangement | Not separately recorded | No |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Unit system | Not separately recorded | Inch |
| Indicative carbon footprint for new product | Not separately recorded | 3.8 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 1.03 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF592 ASingle row tapered roller bearing, cup |
| — | — | — | — | 1.03 kg1030 g |
| SKF592 A/QSingle row tapered roller bearing, cup |
| — | — | — | — | 1.03 kg1030 g |
| SKF592 A/VA983Special single row tapered roller bearing, cup |
| — | — | — | — | 1.05 kg1050 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 592 A | Without | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 592 A/Q | Without | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 592 A/VA983 | Without | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.