210 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 210. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
210 dimensions and recorded technical data
The recorded 210 base designation measures 50×90×20 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 20 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF210Deep groove ball bearing with filling slots |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.497 kg497 g |
| SKF210-2ZDeep groove ball bearing with filling slots and integral sealing |
| 39.1 kN | 34.5 kN | 13000 rpm | 6400 rpm | 0.511 kg511 g |
| SKF210-2ZNRDeep groove ball bearing with filling slots and integral sealing |
| 39.1 kN | 34.5 kN | 13000 rpm | 6400 rpm | 0.51 kg510 g |
| SKF210 NDeep groove ball bearing with filling slots and snap ring groove |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.475 kg475 g |
| SKF210 NRDeep groove ball bearing with filling slots and snap ring |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.499 kg499 g |
| SKF210 NR/C3Deep groove ball bearing with filling slots and snap ring |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.499 kg499 g |
| SKF210-ZDeep groove ball bearing with filling slots and integral sealing |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.499 kg499 g |
| SKF210-ZNRDeep groove ball bearing with filling slots and integral sealing |
| 39.1 kN | 34.5 kN | 13000 rpm | 8000 rpm | 0.514 kg514 g |
| INA210-XL-KRRDeep groove ball bearing |
| 37.5 kN | 23.2 kN | — | — | 0.57 kg570 g |
| INA210-XL-NPP-BSelf-aligning deep groove ball bearings |
| 37.5 kN | 23.2 kN | — | — | 0.43 kg430 g |
| TIMKEN210KDDFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210KDDGFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210KDFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210KFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210KGFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210KRRDeep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.59 kg590 g |
| TIMKEN210PFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210PPFS50000Deep groove ball bearing |
| 35.1 kN | 23.2 kN | — | — | 0.48 kg480 g |
| TIMKEN210RN91 R3Cylindrical roller bearing |
| 1390 kN | 2020 kN | — | — | 34.14 kg34140 g |
| TIMKEN210WDeep groove ball bearing |
| 46 kN | 34.8 kN | — | — | 0.04 kg40 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 210 | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 210-2Z | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 210-2ZNR | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 210 N | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 210 NR | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 210 NR/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 210-Z | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 210-ZNR | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| INA 210-XL-KRR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA 210-XL-NPP-B | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| TIMKEN 210KDDFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210KDDGFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210KDFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210KFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210KGFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210KRR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210PFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210PPFS50000 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 210RN91 R3 | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| TIMKEN 210W | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
210
Deep groove ball bearing with filling slots
View full technical record →SKF210-2Z
Deep groove ball bearing with filling slots and integral sealing
View full technical record →SKF210-2ZNR
Deep groove ball bearing with filling slots and integral sealing
View full technical record →KOYO21063/212
Tapered roller bearing
View full technical record →TIMKEN21075 / 21212
Tapered roller bearing
View full technical record →TIMKEN21075 / 21213
Tapered roller bearing
View full technical record →TIMKEN21075-90010
Tapered roller bearing
View full technical record →TIMKEN21075-90011
Tapered roller bearing
View full technical record →TIMKEN21075-90021
Tapered roller bearing
View full technical record →TIMKEN210KDDFS50000
Deep groove ball bearing
View full technical record →TIMKEN210KDDGFS50000
Deep groove ball bearing
View full technical record →TIMKEN210KDFS50000
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.