Bicycle bearing press & puller tools: hub, pivot and headset size guide
Choose a bicycle bearing tool by the component, bearing dimensions and accessible support surfaces—not by the words bike bearing press alone. A hub installation press, a suspension-pivot extractor and a headset cup press do different jobs. This reference compares named tools and adapter sizes so you can check a candidate against the bicycle component's own service procedure.
On this page19 sections ⌄
Which tool does the job? Hub vs pivot vs headset vs bottom bracket
Use this table to choose the tool category first. A full kit can still lack the adapter or access needed for one particular frame. Mountain-bike, road-bike and wheel-bearing labels do not define a common bearing interface.
On smaller screens, scroll the table sideways to read all columns.
| Actual component | Tool function to look for | Documented examples / boundary |
|---|---|---|
| Cartridge-bearing hub | Aligned installation around the axle/shoulders | Park HBP-1; Enduro BRT-060-Z. Installation drifts alone do not provide blind extraction. |
| Suspension pivot / linkage | Supported extraction and installation | RRP BPET; Park SBK-1. Check the surrounding linkage, not only bearing diameter. |
| Blind bearing with no rear driving access | Internal engagement and a suitable withdrawal method | Enduro BRT-222. A suitable bore still needs secure collet engagement and a clear pulling direction. |
| Pressed headset cup | Cup support and enough working length | Park HHP-2/HHP-3. An integrated headset bearing seated directly in the frame is not a removable cup. |
| Press-fit bottom bracket | Remover and installation bushings matched to the assembly | Park BBT-90.3 plus a separate press for its supported systems. |
| Loose-ball cup-and-cone hub | Cone adjustment and component inspection | Do not select a cartridge press merely because the hub contains ball bearings. |
RRP bearing press adapter chart: bore, outside diameter and kit code
RRP's current BPET chart, grouped by tool kit. Values are bearing bore and outside diameter in millimetres; bearing width is not specified here.
One adapter grouping is not a bearing-interchange declaration. Compare full bearing construction, width and the component specification separately. The BPET handle/tool and bearing adapter kits are separate items in the manufacturer's system.
On smaller screens, scroll the table sideways to read all columns.
| Bearing marking(s) in RRP chart | Kit | Tool adapter code | Bore mm | Outside mm |
|---|---|---|---|---|
| 6882RS | 1 | BPET688 | 8 | 16 |
| 6982RS / 398V | 2 | BPET698 | 8 | 19 |
| 6082RS / 608E-2RS | 3 | BPET608 | 8 | 22 |
| 6092RS | 3a | BPET609 | 9 | 24 |
| 68002RS / 618002RS | 4 | BPET6800 | 10 | 19 |
| 69002RS / 619002RS | 5 | BPET6900 | 10 | 22 |
| 60002RS | 6 | BPET6000 | 10 | 26 |
| 68012RS / 618012RS | 6a | BPET6801 | 12 | 21 |
| 69012RS / 619012RS | 7 | BPET6901 | 12 | 24 |
| 60012RS | 8 | BPET6001 | 12 | 28 |
| 38022RS / 638022RS / 68022RS / 618022RS | 9 | BPET63802 | 15 | 24 |
| 15262RS | 10 | BPET1526 | 15 | 26 |
| 69022RS / 6902E-2RS / 619022RS / 7902 | 11 | BPET6902 | 15 | 28 |
| 60022RS | 12 | BPET6002 | 15 | 32 |
| 68032RS / 618032RS | 13 | BPET6803 | 17 | 26 |
| 172872RS | 13a | BPET17287 | 17 | 28 |
| 69032RS / 6903E-2RS / 619032RS / 61903E-2RS | 14 | BPET6903 | 17 | 30 |
| 60032RS | 15 | BPET6003 | 17 | 35 |
| 68042RS / 618042RS | 16 | BPET6804 | 20 | 32 |
| 6805 / 618052RS | 17 | BPET6805 | 25 | 37 |
RRP BPET: red extraction parts and blue installation parts
The manual identifies kits 1, 2, 3 and 3a as female-adapter-only exceptions; do not force them into the generic male/female drawing. The source describes inner-ring loading during extraction. BearingScope therefore does not infer that an extracted bearing is suitable for reuse. The tool's deliberately limited handle leverage is not an invitation to fit an extension.
On smaller screens, scroll the table sideways to read all columns.
| Operation | Supported sequence |
|---|---|
| Before use | Confirm the matching kit and a flat support face. Seat the parts squarely; the receiving cup must sit flush against the frame or hub. |
| Extraction | Use the red arrangement. Take up the handle until the components contact, check alignment, then draw the bearing into the receiving cup. Pause after a couple of turns to check its path. |
| Installation | Use the blue arrangement with the driver acting on the outer ring for insertion into the housing. Align, begin pressing and pause after a couple of turns to check seating. |
| Stop | Do not overcome misalignment with extra force. A collapsing, seized or damaged bearing requires reassessment, not continued winding. |
Park HBP-1 hub press: supported bearing dimensions
The manufacturer's compatibility sheet lists these bore/outside-diameter pairs. The entries describe tool selection, not complete bearing models or a universal hub fit.
The same sheet separately lists spacer IDs of 12, 15, 17 and 20 mm. These are spacer dimensions, not additional bearing size pairs. HBP-1 is an installation set; a bearing puller is a separate selection.
On smaller screens, scroll the table sideways to read all columns.
| Bearing bore mm | Listed outside diameters mm |
|---|---|
| 8 | 16, 22 |
| 9 | 20, 22, 24 |
| 10 | 19, 22, 26 |
| 12 | 18, 21, 24, 27 |
| 15 | 21, 24, 26, 28 |
| 17 | 26, 30 |
| 20 | 27, 32, 37 |
Hub press setup: pilots, bushings and the axle are not interchangeable
HBP-1 uses a pilot to locate the bearing and pressing bushing. Select the pilot by bearing bore. If the hub axle has a bearing-locating shoulder, the axle can provide the guidance instead. The chosen bushing must match the bearing and the required pressing arrangement; a large washer is not a substitute for verifying ring contact.
Follow the hub manufacturer's sequence, including spacer placement and which bearing seats first. The HBP-1 instructions explicitly defer to that assembly's requirements. A chart entry such as 15×28 mm does not establish axle shoulder clearance, spacer length, press force or final preload. Record those separately before work.
Park SBK-1 suspension bearing kit: the support condition matters
SBK-1 removes and installs bicycle pivot bearings using size-matched cup/drifts, extractor studs and pilots. Its extraction arrangement needs at least 3 mm of flat linkage structure outside the bearing for cup support. Without that support, the manual points to considering a different extraction method; it does not approve forcing the cup against an irregular frame.
Select the cup/drift from bearing OD and the extractor stud from bearing ID. The larger cup side receives the extracted bearing; the smaller side serves installation. Installation pilots must slip into the bore; the bare pressing shaft centres 8.5–9 mm bores. Do not confuse pilot clearance with bearing fit tolerance.
Can one suspension tool fit every frame?
No. Bearing size, support width, linkage access and the tool stack all matter. SBK-1's specified 3 mm support requirement is one concrete example of a condition missed by diameter-only selection.
Is a pivot press the same as a shock-bushing tool?
Not necessarily. Identify whether the part is a rolling bearing, plain bushing or mounting hardware. This pivot-bearing reference does not approve a tool for an unspecified shock eyelet.
HHP-2 vs HHP-3: working length and pressing interfaces
These are tool specifications, not bearing size substitutions or press-force ratings. HHP-3 also lists supported press-fit bottom-bracket systems, but the appropriate bearing/cup drifts still have to match the specific assembly.
For HHP-2, do not use a cup guide that binds in the cup or loads a pre-installed cup-bearing unit. Its manual advises pressing one cup at a time when guides are not used. Keep the cups aligned as they enter and stop when correctly seated; do not treat a longer working envelope as permission for more force.
On smaller screens, scroll the table sideways to read all columns.
| Reference | Park HHP-2 | Park HHP-3 |
|---|---|---|
| Intended cup range | 1, 1⅛, 1¼ and 1½ inch headset systems | 1 to 1½ inch headset systems |
| Maximum working length | 315 mm | 385 mm |
| Interface measurements | Stepped bushings: 25.7 / 29.7 / 32.8 mm | Nominal shaft: 16 mm; nominal plates: 63 mm |
| Mechanism | Quick-release sliding plate | Threaded shaft and press plates |
BBT-90.3: a bottom-bracket remover with installation bushings
BBT-90.3 is documented for many press-fit bottom brackets using 22 or 24 mm spindles, including BB90 and BB92. Those spindle dimensions are not a claim that every bearing has a 22 or 24 mm bore. The set includes a remover and two bushings; installation additionally needs a suitable cup press such as HHP-2 or HHP-3.
In its prescribed removal arrangement, the flared end engages behind the bearing or sleeve and force is applied to the tapered end cap. For installation, the bushings, bearing and frame shell are held in an aligned press stack, seating to the assembly's stop. Verify the actual frame/unit instructions and tool engagement before applying force. This does not authorize driving out a threaded cup or substituting the tool for a 19 mm BMX assembly.
Abbey Modular Bearing Press: what the standard configuration contains
Abbey recommends pressing bearings individually and using the centring cone in the empty side to keep the press aligned. The list describes the standard handled configuration reviewed here; check the actual supplied kit and component requirements. A ½ inch thread label is a tool interface, not the minimum bearing bore that every arrangement can service.
On smaller screens, scroll the table sideways to read all columns.
| Component | Manufacturer-listed configuration |
|---|---|
| Press mechanism | Thrust-bearing press head, handles and Quick Nut |
| Shaft | 12 inch shaft with ½ inch ACME thread |
| Bottom-bracket drifts | 24 mm; single non-drive GXP 22 mm; 28.9 mm DUB; 6806 for BB30 |
| Other guides | PF30 / 1.125 inch headset; 1.5 inch headset; centring cone |
Enduro BRT tools: linear press, blind puller and pivot guides
Select by function as well as brand. A press set and a slide-hammer puller load and support the assembly differently. No shared adapter compatibility between these tools, Abbey, Park or RRP is inferred from a similar diameter.
On smaller screens, scroll the table sideways to read all columns.
| Tool | Documented function / dimensions | Selection boundary |
|---|---|---|
| BRT-060-Z | Hub guides: 6800, 6802, 6803, 6900, 6901, 6902, 6903, MR 1526, MR 1830 | Includes separate hub/suspension press rods and Zip-Nut; not a blanket frame approval. |
| BRT-060-Z suspension pieces | Inner pusher pilots: 8/10/11, 15/17 and 18/20 mm; receiver cups cover 12–32 mm ODs | Check the actual cup/guide combination and support geometry. |
| BRT-222 | Blind-hole extraction; published bearing-ID range 8–32 mm | The range is not a replacement claim for an older 8–25 mm tool. |
| BRT-222 collet connection | ½ inch–12 BSW; major diameter 12.7 mm | Thread pitch and thread form must match; nominal diameter alone is insufficient. |
| BRT-051 | Pivot extractor guides used with the smallest Multi Press threaded rod | An accessory guide kit, not a complete standalone press; the public description does not list every covered size. |
What to measure before selecting a press or extractor
Record actual measurements in millimetres alongside the maker's labels. Do not use the catalogue bearing code as a press-force specification, or use shipping dimensions as an adapter drawing. If one field is unknown, retain it as an open compatibility question.
On smaller screens, scroll the table sideways to read all columns.
| Field | Why it changes the selection |
|---|---|
| Complete bearing marking; bore, OD and width | Distinguishes the bearing from the tool code and captures dimensions absent from two-diameter charts. |
| Axle/shaft through the bore | Determines whether the pilot, rod or extractor can enter. |
| Shoulder, circlip and internal spacer | Determines the removal direction and whether another part blocks engagement. |
| Flat support around the seat | Determines whether the receiving cup can react the load without bearing on an edge. |
| Depth and clear withdrawal space | A tool can match the bore yet run out of reach or have nowhere to receive the bearing. |
| Drift-to-ring contact | Determines whether installation load reaches the intended ring or travels through rolling elements. |
| Exact frame/hub procedure | Supplies the preparation, order, seating and adjustment that generic tool dimensions cannot. |
Common press and puller questions
What tool do I need for a 6902 bicycle bearing?
RRP lists the 15×28 mm group under kit 11, BPET6902. Park HBP-1 lists 15×28 mm for installation, and Enduro BRT-060-Z includes a 6902 hub guide. These are candidates for different arrangements, not permission to use any of them in every 6902-equipped frame.
Can I use a headset press for wheel bearings?
Only if the complete press, guides, shaft clearance and bearing contact arrangement are specified for that hub. A headset cup-press label alone does not establish hub compatibility.
Which bike bearing press is best?
This reference compares measurable scope and configurations, not an untested ranking. Start with your actual hub/pivot/cup inventory, access requirements and required adapters; published dimensions cannot establish long-term durability or comparative test performance.
Can I make a press from threaded rod and washers?
This page does not provide a rated homemade design. Material strength, alignment, ring contact, support and retention would all need to be established; copying a commercial tool's diameter does not establish safe capacity.
Are extracted bearings reusable?
Do not assume so. Some extraction arrangements load the inner ring while overcoming an outer-ring fit. Follow the component/bearing maker's reuse policy and inspection criteria; this table is not a reuse approval.
What the evidence can — and cannot — tell you
| Observation or context | Interpretation to consider | Verification needed |
|---|---|---|
| Bearing code or dimensions | Identifies a possible adapter | Also check ring contact, bearing width, shoulders and access. |
| Press and extraction kit | May support two different operations | Use the installation and removal configurations separately. |
| Fits a bearing diameter | Only one compatibility condition | Does not approve the tool for every frame or hub containing that bearing. |
Plan the work safely
Identify and record
Identify hub cartridge, suspension pivot, bottom-bracket unit or headset cup; retain the exact assembly and bearing markings.
Check the context
Measure bearing bore and outside diameter, then check shaft passage, extraction clearance and the flat support available around the seat.
Verify before acting
Match the manufacturer's adapter chart and complete tool configuration; follow the component's instructions for retention, preparation and seating.
Keep the decision traceable
Stop for misalignment, damaged support or unexpected force. After assembly, verify seating, free movement and the specified adjustment before use.
Capture the information a model search cannot guess
Keep this checklist with your inspection or comparison. Checking a box only records that you have collected the item; it does not certify the bearing.
0 of 4 information groups recorded.
Technical basis & editorial scope
Original BearingScope workflow, written for catalogue research and comparison. Manufacturer material is used to check principles, not copied as a product endorsement or substituted for model-specific instructions. Reviewed 1 October 2026.
- Rapid Racer Products — BPET adapter chart — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Rapid Racer Products — BPET instructions — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — HHP-2 specifications — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — HHP-3 specifications — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — HHP-2 instructions — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — HBP-1 compatibility chart — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — HBP-1 instructions — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — SBK-1 instructions, April 2026 — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Park Tool — BBT-90.3 instructions — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Abbey Bike Tools — Modular Bearing Press — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Enduro — BRT-060-Z — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Enduro — BRT-222 — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
- Enduro — BRT-051 — Named tool configuration and dimensions; not universal frame compatibility. Reviewed 2 October 2026.
Source addresses and collection status are retained in the internal audit. No unpublished dimensions, torque settings, service intervals or interchange approvals are inferred.