Exact model answerSET14: cone, cup and complete bearing dimensions
TIMKEN SET14 identifies the cone L44643 and cup L44610 in the manufacturer record. The matched pair has bore d = 25.400 mm, outside diameter D = 50.292 mm and assembled width T = 14.224 mm. These are measurements for that complete cone-and-cup combination.
Do not confuse the assembled width with a separate ring: cone width B is 14.732 mm, while cup width C is 10.668 mm. Read T directly from the matched-pair record; adding B and C does not give the assembled width.
The SET designation is the lookup name in the manufacturer feed; the dimensional catalogue identifies the components as L44643 / L44610. This connection establishes the listed component geometry, not identical packaging, a matching UPC, a supplied seal or an approved vehicle application.
- Record marking
- SET14
- Cone / inner assembly
- L44643
- Cup / outer ring
- L44610
Read each measurement separately
Bearing dimensions · published units retained| Measurement | Symbol | Metric | Inches |
|---|
| Bore (d) | d | 25.400 mm | 1 in |
|---|
| O.D. (D) | D | 50.292 mm | 1.9800 in |
|---|
| Width (T) | T | 14.224 mm | 0.56 in |
|---|
| Inner Ring Width (B) | B | 14.732 mm | 0.5800 in |
|---|
| Outer Ring Width (C) | C | 10.668 mm | 0.4200 in |
|---|
| Effective Center Location | Not specified | -3.3 mm | -0.13 in |
|---|
Mounting measurements and source limitations
Mounting dimensions · published units retained| Measurement | Symbol | Metric | Inches |
|---|
| Max Shaft Fillet Radius | Not specified | 1.270 mm | 0.050 in |
|---|
| Max Housing Fillet Radius | Not specified | 1.27 mm | 0.050 in |
|---|
| Shaft Backing Shoulder Dia. - Frontface (da) | da | 30 mm | 1.18 in |
|---|
| Shaft Backing Shoulder Dia. - Backface (db) | db | 32 mm | 1.26 in |
|---|
| Housing Backing Shoulder Dia. - Frontface (Da) | Da | 47.50 mm | 1.87 in |
|---|
| Housing Backing Shoulder Dia. - Backface (Db) | Db | 44.45 mm | 1.75 in |
|---|
| Cage Location rel. to BF (Aa) | Aa | 0.5 mm | 0.02 in |
|---|
| Cage Location rel. to FF (Ab) | Ab | 1.3 mm | 0.05 in |
|---|
What to check on your bearing
- Read the complete cone and cup markings. This record requires L44643 together with L44610; a similar-looking suffix or an extra prefix must be checked separately.
- For size identification, distinguish the shaft-side bore d, housing-side diameter D and assembled width T. For an unassembled ring, compare B or C with the corresponding row instead.
- Check the named front/back face before using a shoulder diameter or cage offset. Minimum and maximum qualifiers remain part of the measurement.
- Use the equipment procedure and the exact bearing specification to determine fits, adjustment, lubrication and operating limits. These nominal dimensions do not supply preload, end play or tightening torque.
This is a dated dimensional reference, not a replacement approval or a manufacturer-certified drawing. Similar dimensions do not establish matching geometry, load capability, clearance, material or operating limits.
Factual reference: Timken component-identity feed and official dimensional catalogue; catalogue snapshot 2026-10-02. Interpretation and checking notes by BearingScope.
Technical documents & data sheet
This product page is a BearingScope catalogue reference, not a manufacturer-certified drawing. Preserve the full brand and designation when comparing files.
- Record identity
- TIMKEN SET14
- Document matching
- Exact designation, assembly scope, revision and units must agree.
No verified redistributable CAD or manufacturer PDF is registered for this exact model. A catalogue image is not a dimensioned drawing. Missing technical files are not generated or replaced with unrelated models.
Look up another model or check drawing requirements →
