Exact model answer565 / 562: cone, cup and complete bearing dimensions
TIMKEN 565 / 562 identifies the cone 565 and cup 562 in the manufacturer record. The matched pair has bore d = 63.500 mm, outside diameter D = 130.048 mm and assembled width T = 36.515 mm. These are measurements for that complete cone-and-cup combination.
Do not confuse the assembled width with a separate ring: cone width B is 36.170 mm, while cup width C is 28.575 mm. Read T directly from the matched-pair record; adding B and C does not give the assembled width.
- Record marking
- 565 / 562
- Cone / inner assembly
- 565
- Cup / outer ring
- 562
Read each measurement separately
Bearing dimensions · published units retained| Measurement | Symbol | Metric | Inches |
|---|
| Bore (d) | d | 63.500 mm | 2 1/2 in |
|---|
| O.D. (D) | D | 130.048 mm | 5.1200 in |
|---|
| Width (T) | T | 36.515 mm | 1.4376 in |
|---|
| Inner Ring Width (B) | B | 36.170 mm | 1.4240 in |
|---|
| Outer Ring Width (C) | C | 28.575 mm | 1.125 in |
|---|
| Effective Center Location | Not specified | -8.1 mm | -0.32 in |
|---|
Mounting measurements and source limitations
Mounting dimensions · published units retained| Measurement | Symbol | Metric | Inches |
|---|
| Max Shaft Fillet Radius | Not specified | Withheld — source units disagree | Withheld — verify current drawing |
|---|
| Max Housing Fillet Radius | Not specified | 0.76 mm | 0.03 in |
|---|
| Shaft Backing Shoulder Dia. - Frontface (da) | da | 73 mm | 2.87 in |
|---|
| Shaft Backing Shoulder Dia. - Backface (db) | db | 80 mm | 3.15 in |
|---|
| Housing Backing Shoulder Dia. - Frontface (Da) | Da | 121.90 mm | 4.80 in |
|---|
| Housing Backing Shoulder Dia. - Backface (Db) | Db | 116.08 mm | 4.57 in |
|---|
| Cage Location rel. to BF (Aa) | Aa | 2.5 mm | 0.1 in |
|---|
| Cage Location rel. to FF (Ab) | Ab | 2.8 mm | 0.11 in |
|---|
What to check on your bearing
- Read the complete cone and cup markings. This record requires 565 together with 562; a similar-looking suffix or an extra prefix must be checked separately.
- For size identification, distinguish the shaft-side bore d, housing-side diameter D and assembled width T. For an unassembled ring, compare B or C with the corresponding row instead.
- Check the named front/back face before using a shoulder diameter or cage offset. Minimum and maximum qualifiers remain part of the measurement.
- Use the equipment procedure and the exact bearing specification to determine fits, adjustment, lubrication and operating limits. These nominal dimensions do not supply preload, end play or tightening torque.
Some optional mounting entries have metric and inch figures that do not reconcile at their displayed precision: Max Shaft Fillet Radius. Both numeric versions are withheld in this supplement. Verify the current manufacturer drawing before using those particular limits.
This is a dated dimensional reference, not a replacement approval or a manufacturer-certified drawing. Similar dimensions do not establish matching geometry, load capability, clearance, material or operating limits.
Factual reference: Timken component-identity feed and official dimensional catalogue; catalogue snapshot 2026-10-02. Interpretation and checking notes by BearingScope.
Technical documents & data sheet
This product page is a BearingScope catalogue reference, not a manufacturer-certified drawing. Preserve the full brand and designation when comparing files.
- Record identity
- TIMKEN 565 / 562
- Document matching
- Exact designation, assembly scope, revision and units must agree.
No verified redistributable CAD or manufacturer PDF is registered for this exact model. A catalogue image is not a dimensioned drawing. Missing technical files are not generated or replaced with unrelated models.
Look up another model or check drawing requirements →
