UCT 210 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with UCT 210. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
UCT 210 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 7 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for UCT 210
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG UCT210 — 20 dimension fields
Take-up housing unit. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
This record can describe a housed unit rather than a loose bearing. Housing length, bolt spacing and centre height must be checked separately from shaft bore; do not interpret them as bearing outside diameter.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Height | H | 117 mm |
| Length total | L | 149 mm |
| Distance shaft axis | L1 | 90 mm |
| Length fixed link | L2 | 16 mm |
| Length guidance groove | L3 | 86 mm |
| Width housing fixing side | A | 49 mm |
| Width recess | N1 | 19 mm |
| Height recess | N2 | 49 mm |
| Width inner ring | B | 51.6 mm |
| Distance of raceway to locking collar | S1 | 32.6 mm |
| Height housing fixing side | T | 83 mm |
| Width housing | A2 | 37 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Width guidance groove | A1 | 16 mm |
| Upper width guidance groove tolerance | Not supplied separately | 0.2 mm |
| Lower width guidance groove tolerance | Not supplied separately | 0 mm |
| Distance guidance grooves | H1 | 102 mm |
| Upper distance guidance groove tolerance | Not supplied separately | 0 mm |
| Lower distance guidance groove tolerance | Not supplied separately | -0.5 mm |
| Fixing bore | N | 29 mm |
Catalogue parameters for UCT 210
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO UCT210 — 21 recorded parameters
Ball bearing unit
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
This can be a unit or housing record. Bolt spacing, housing envelope, centre height and the insert identity need separate checks; do not interpret every outside dimension as bearing D.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 50 mm |
| A | Not separately recorded | 49 mm |
| A1 | Not separately recorded | 16 mm |
| A2 | Not separately recorded | 37 mm |
| H | Not separately recorded | 117 mm |
| H1 | Not separately recorded | 102 mm |
| H2 | Not separately recorded | 83 mm |
| L | Not separately recorded | 149 mm |
| L1 | Not separately recorded | 90 mm |
| L2 | Not separately recorded | 16 mm |
| L3 | Not separately recorded | 86 mm |
| N | Not separately recorded | 29 mm |
| N1 | Not separately recorded | 19 mm |
| N2 | Not separately recorded | 49 mm |
| B | Not separately recorded | 51.6 mm |
| S | Not separately recorded | 19 mm |
| Basic Load Ratings : Cr | Not separately recorded | 35.1 kN |
| Basic Load Ratings : C0R | Not separately recorded | 23.3 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 1.06 kN |
| Factor : F0 | Not separately recorded | 14.4 |
| Nipple Size | Not separately recorded | 1/4-28UNF |
NTN UCT210 — 19 recorded parameters
Bearing units
Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.
The original dimension names below control this record. Component, washer and assembly measurements must not be substituted for each other.
Recorded closure for UCT210: seal with slinger. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Dimensions and properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Housing width (HB2, C) (A) | Not separately recorded | 49 mm |
| Guidance groove width (T) (A1) | Not separately recorded | 16 mm |
| Housing width (T) (A2) | Not separately recorded | 37 mm |
| Insert IR width (B) | Not separately recorded | 51.6 mm |
| Bore diameter (shaft diameter) | Not separately recorded | 50 mm |
| Overall height (T) (H) | Not separately recorded | 117 mm |
| Distance between bottom of guidance grooves (T) (H1) | Not separately recorded | 102 mm |
| Height of attachment end (T) (H2) | Not separately recorded | 83 mm |
| Housing length (T) (L) | Not separately recorded | 151 mm |
| Distance to bearing center line (T) (L1) | Not separately recorded | 92 mm |
| Thickness of attachment end (T) (L2) | Not separately recorded | 18 mm |
| Length of guidance groove (T) (L3) | Not separately recorded | 86 mm |
| Dia. of attachment bolt hole (T, T2) (N) | Not separately recorded | 29 mm |
| Length of attachment slot | N1 | 19 mm |
| Height of attachment slot | N2 | 49 mm |
| Radius (T) (r) | Not separately recorded | 59 mm |
| middle of bearing raceway (S) | Distance IR face | 19 mm |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue construction | Not separately recorded | Grey cast housing, radial insert ball bearing with socket set screws,seal with slinger |
| Closure construction | Not separately recorded | seal with slinger |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| FAGUCT210Take-up housing unit |
| — | — | — | — | 2.6 kg2600 g |
| KOYOUCT210Ball bearing unit |
| 35.1 kN | 23.3 kN | — | — | — |
| NTNUCT210Ball bearing unit |
| — | — | — | — | — |
| FAGUCT210-29Take-up housing unit |
| — | — | — | — | 2.64 kg2640 g |
| FAGUCT210-30Take-up housing unit |
| — | — | — | — | 2.539 kg2539 g |
| FAGUCT210-31Take-up housing unit |
| — | — | — | — | 2.54 kg2540 g |
| FAGUCT210-32Take-up housing unit |
| — | — | — | — | 2.487 kg2487 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| FAG UCT210 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| KOYO UCT210 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN UCT210 | seal with slinger | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| FAG UCT210-29 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCT210-30 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCT210-31 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCT210-32 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
UCT210
Take-up housing unit
View full technical record →KOYOUCT210
Ball bearing unit
View full technical record →NTNUCT210
Ball bearing unit
View full technical record →FAGUCT210-29
Take-up housing unit
View full technical record →FAGUCT210-30
Take-up housing unit
View full technical record →FAGUCT210-31
Take-up housing unit
View full technical record →FAGUCT210-32
Take-up housing unit
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.