UCPA205 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with UCPA205. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
UCPA205 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 5 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for UCPA205
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG UCPA205 — 8 dimension fields
Plummer block housing unit. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
This record can describe a housed unit rather than a loose bearing. Housing length, bolt spacing and centre height must be checked separately from shaft bore; do not interpret them as bearing outside diameter.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Length total | L | 84 mm |
| Height | H2 | 72 mm |
| Distance shaft axis | H | 36.5 mm |
| Width (base) | A | 38 mm |
| Width of inner ring | B | 34.1 mm |
| Distance of raceway to locking collar | S1 | 19.8 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Distance fixing bore | J | 56 mm |
Catalogue parameters for UCPA205
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
FAG UCPA205 — 21 recorded parameters
Plummer block housing unit
Reference: Schaeffler medias — FAG; source snapshot 2026-10-03.
UCPA205 is a short-base cast-iron housing unit, not a bare bearing. Shaft bore d is 25 mm, total housing length L 84 mm, overall height H2 72 mm and shaft-centre height H 36.5 mm.
Mounting-hole spacing J is 56 mm and fixing thread K is M10. Compare base width A and insert width B separately; housing length and height are not a rolling-bearing outside diameter and width.
The additional-information table identifies the housing and insert separately. Its J7 housing-clearance variant is not a shaft-fit recommendation or permission to interchange complete units.
Manufacturer product identity and parameters checked on 2026-10-03. A catalogue reference is not a certified drawing or an application approval.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Length total | L | 84 mm |
| Height | H 2 | 72 mm |
| Basic dynamic load rating, radial | C r | 14,900 N |
| Basic static load rating, radial | C 0r | 7,800 N |
| Fatigue load limit, radial | C ur | 410 N |
| Weight | ≈m | 0.891 kg |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Distance fixing bore | J | 56 mm |
| Thread fixing bore | K | M10 |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Distance shaft axis | H | 36.5 mm |
| Width (base) | A | 38 mm |
| Connection thread for lubrication | Q | M6 |
| Width of inner ring | B | 34.1 mm |
| Distance of raceway to locking collar | S 1 | 19.8 mm |
Additional information
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Housing | Not separately recorded | PA205 |
| Bearing designation | Not separately recorded | UC205 |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | T min | -20 °C |
| Operating temperature max. | T max | 120 °C |
Recorded construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Material | Not separately recorded | GG — Grey cast iron |
| Housing clearance | Not separately recorded | J7 — Normal swivel torque |
| Material | Not separately recorded | GG — Cast iron |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| FAGUCPA205Plummer block housing unit |
| — | — | — | — | 0.891 kg891 g |
| FAGUCPA205-13Plummer block housing unit |
| — | — | — | — | 0.87 kg870 g |
| FAGUCPA205-14Plummer block housing unit |
| — | — | — | — | 0.86 kg860 g |
| FAGUCPA205-15Plummer block housing unit |
| — | — | — | — | 0.84 kg840 g |
| FAGUCPA205-16Plummer block housing unit |
| — | — | — | — | 0.83 kg830 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| FAG UCPA205 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCPA205-13 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCPA205-14 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCPA205-15 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
| FAG UCPA205-16 | Not recorded | Not recorded | Not recorded | Not recorded | GG — Grey cast iron | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
UCPA205
Plummer block housing unit
View full technical record →FAGUCPA205-13
Plummer block housing unit
View full technical record →FAGUCPA205-14
Plummer block housing unit
View full technical record →FAGUCPA205-15
Plummer block housing unit
View full technical record →FAGUCPA205-16
Plummer block housing unit
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.