PB10 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with PB10. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
PB10 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 1 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for PB10
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
IKO PB10 — 9 recorded parameters
Lubrication-type PILLOBALL spherical bushing, insert type
Reference: IKO PILLOBALL catalogue, K37 (PDF page 5); source snapshot 2026-10-03.
PB10 is a spherical sliding bushing, not a rolling ball bearing: 10 mm bore, 26 mm housing diameter and 14 mm inner-member width. The outer member is 10.5 mm wide.
The listed load capacities use the PILLOBALL catalogue method; they are not rolling-bearing C/C0 inputs for an L10 calculator. This lubrication-type insert is not a maintenance-free EC rod end.
Manufacturer dimension table
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore | d | 10 mm |
| Outside diameter | D | 26 mm |
| Outer-member width | C | 10.5 mm |
| Inner-member width | B | 14 mm |
| Ball diameter | Not separately recorded | 19.050 mm (3/4 in) |
| Minimum chamfer dimension | rs min | 0.2 mm |
| Reference mass | Not separately recorded | 39 g |
| Dynamic load capacity | Cd | 9,810 N |
| Static load capacity | Cs | 23,500 N |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| IKOPB10Rod end |
| 9.81 kN | 23.5 kN | — | — | 0.039009 kg39.009 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| IKO PB10 | Not recorded | Not recorded | Not recorded | Not recorded | High Carbon Steel | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.