NUTR35 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with NUTR35. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
NUTR35 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 3 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for NUTR35
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
INA NUTR35 — 17 recorded parameters
Yoke type track roller
Reference: Schaeffler medias — INA; source snapshot 2026-10-03.
NUTR35 is a yoke-type track roller with a 35 mm bore, 72 mm outside diameter and 29 mm bearing width. The outer-ring width C is 28 mm.
The current manufacturer record identifies NUTR35 and describes the NUTR..-A construction: two full-complement cylindrical-roller rows, an inner ring and labyrinth seals. The older page-address suffix is not used to infer a different product.
Cr w and C0r w are rating values. Fr per and F0r per are separately listed permissible outer-ring loads; do not substitute one for the other. The stated grease speed is not a guaranteed operating speed for every track or lubrication condition.
Manufacturer product identity and parameters checked on 2026-10-03. A catalogue reference is not a certified drawing or an application approval.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width of the bearing | B | 29 mm |
| Basic dynamic load rating, radial | C r w | 45,500 N |
| Basic static load rating, radial | C 0r w | 65,000 N |
| Fatigue load limit, radial | C ur w | 8,900 N |
| Speed on permanent grease lubrication | n D G | 2,100 1/min |
| Permissible static load, radial | F 0r per | 62,000 N |
| Permissible dynamic load outer ring, radial | F r per | 31,500 N |
| Weight | ≈m | 0.629 kg |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Width, outer ring | C | 28 mm |
| Stop diameter of thrust washer | d 2 | 44 mm |
| Minimum chamfer dimension | r min | 1.1 mm |
| Minimum chamfer dimension | r 1 min | 0.6 mm |
Recorded construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Sealing | Not separately recorded | 2LB — Labyrinth seals on both sides |
| Outer ring profile | Not separately recorded | IOP — Optimized INA-profile |
| Relubrication | Not separately recorded | IR — Via inner ring |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| INANUTR35Yoke type track roller |
| 45.5 kN | 65 kN | — | 2100 rpm | 0.629 kg629 g |
| SKFNUTR 35 ASupport roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature |
| 45.7 kN | 57 kN | — | 2000 rpm | 0.63 kg630 g |
| SKFNUTR 35 XSupport roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature |
| 45.7 kN | 57 kN | — | 2000 rpm | 0.63 kg630 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| INA NUTR35 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF NUTR 35 A | Seal on both sides | Not recorded | Between C2 and CN | Without | Bearing steel | Grease |
| SKF NUTR 35 X | Seal on both sides | Not recorded | Between C2 and CN | Without | Bearing steel | Grease |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
NUTR35
Yoke type track roller
View full technical record →INANUTR3580
Yoke type track roller
View full technical record →SKFNUTR 3580 A
Support roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature
View full technical record →SKFNUTR 3580 X
Support roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature
View full technical record →SKFNUTR 35 A
Support roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature
View full technical record →SKFNUTR 35 X
Support roller (yoke-type track roller) with flange rings, integral sealing and relubrication feature
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.