NU244 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with NU244. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
NU244 dimensions and recorded technical data
The recorded NU244 base designation measures 220×400×65 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 15 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for NU244
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO NU244 — 26 recorded parameters
Cylindrical roller bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 220 mm |
| D | Not separately recorded | 400 mm |
| B | Not separately recorded | 65 mm |
| R(Min.) | Not separately recorded | 4 mm |
| R1(Min.) | Not separately recorded | 4 mm |
| Fw | Not separately recorded | 270 mm |
| Ew | Not separately recorded | - mm |
| Basic Load Ratings : Cr | Not separately recorded | 949 kN |
| Basic Load Ratings : C0R | Not separately recorded | 1080 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 123 kN |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 1400 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 1700 min-1 |
| Sd1 | Not separately recorded | - mm |
| B1 | Not separately recorded | - mm |
| B2 | Not separately recorded | - mm |
| Da(Min.) | Not separately recorded | - mm |
| Db(Min.) | Not separately recorded | 236 mm |
| Db(Max.) | Not separately recorded | 266 mm |
| Dc(Min.) | Not separately recorded | - mm |
| Dd(Min.) | Not separately recorded | - mm |
| Da(Max.) | Not separately recorded | 384 mm |
| Db(Max.) | Not separately recorded | - mm |
| Db(Min.) | Not separately recorded | - mm |
| Ra(Max.) | Not separately recorded | 3 mm |
| Rb(Max.) | Not separately recorded | 3 mm |
| Mass(Refer.) | Not separately recorded | 38.5 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| KOYONU244Cylindrical roller bearing |
| 949 kN | 1080 kN | — | 1400 rpmLimiting Speeds(Grease Lub.): 1400 min-1Limiting Speeds(Oil Lub.): 1700 min-1 | 38.5 kg38500 g |
| SKFNU 244 ECMSingle row cylindrical roller bearing, NU design |
| 1060 kN | 1290 kN | 1700 rpm | 1900 rpm | 38.4 kg38400 g |
| SKFNU 244 ECM/C3Single row cylindrical roller bearing, NU design |
| 1060 kN | 1290 kN | 1700 rpm | 1900 rpm | 38.4 kg38400 g |
| SKFNU 244 ECMLSingle row cylindrical roller bearing, NU design |
| 1060 kN | 1290 kN | 1700 rpm | 3000 rpm | 36.8 kg36800 g |
| SKFNU 244 ECML/C3Single row cylindrical roller bearing, NU design |
| 1060 kN | 1290 kN | 1700 rpm | 3000 rpm | 36.8 kg36800 g |
| FAGNU244-E-M1Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 37.2 kg37200 g |
| FAGNU244-E-M1A-C3Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 37.6 kg37600 g |
| FAGNU244-E-M1-C2Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 37.12 kg37120 g |
| FAGNU244-E-M1-C3Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 36.66 kg36660 g |
| FAGNU244-E-M1-J20AA-C3Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 37.8 kg37800 g |
| FAGNU244-E-M1-J30PC-C3Cylindrical roller bearing |
| 950 kN | 1330 kN | 1380 rpm | 2600 rpm | 38.2 kg38200 g |
| TIMKENNU244EMACylindrical roller bearing |
| 1040 kN | 1290 kN | — | — | 36.9 kg36900 g |
| TIMKENNU244EMAC3Cylindrical roller bearing |
| 1040 kN | 1290 kN | — | — | 36.9 kg36900 g |
| TIMKENNU244EMAC4Cylindrical roller bearing |
| 1040 kN | 1290 kN | — | — | 36.9 kg36900 g |
| NSKNU244EMCylindrical roller bearing |
| 1110 kN | 1250 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| KOYO NU244 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF NU 244 ECM | Without | Not recorded | CN | Machined brass | Not recorded | None |
| SKF NU 244 ECM/C3 | Without | Not recorded | C3 | Machined brass | Not recorded | None |
| SKF NU 244 ECML | Without | Not recorded | CN | Machined brass | Not recorded | None |
| SKF NU 244 ECML/C3 | Without | Not recorded | C3 | Machined brass | Not recorded | None |
| FAG NU244-E-M1 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU244-E-M1A-C3 | Not recorded | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M1A — Two Piece Brass Cage Lip guided | Not recorded | Not recorded |
| FAG NU244-E-M1-C2 | Not recorded | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU244-E-M1-C3 | Not recorded | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU244-E-M1-J20AA-C3 | Not recorded | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU244-E-M1-J30PC-C3 | Not recorded | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| TIMKEN NU244EMA | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| TIMKEN NU244EMAC3 | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| TIMKEN NU244EMAC4 | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| NSK NU244EM | Not recorded | Not recorded | Not recorded | Machined brass | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
NU244
Cylindrical roller bearing
View full technical record →SKFNU 244 ECM
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 244 ECM/C3
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 244 ECML
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 244 ECML/C3
Single row cylindrical roller bearing, NU design
View full technical record →NSKNU244EM
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1A-C3
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1-C2
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1-C3
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1-J20AA-C3
Cylindrical roller bearing
View full technical record →FAGNU244-E-M1-J30PC-C3
Cylindrical roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.