NU1007 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with NU1007. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
NU1007 dimensions and recorded technical data
The recorded NU1007 base designation measures 35×62×14 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 15 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for NU1007
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO NU1007 — 26 recorded parameters
Cylindrical roller bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 35 mm |
| D | Not separately recorded | 62 mm |
| B | Not separately recorded | 14 mm |
| R(Min.) | Not separately recorded | 1 mm |
| R1(Min.) | Not separately recorded | 0.6 mm |
| Fw | Not separately recorded | 42 mm |
| Ew | Not separately recorded | - mm |
| Basic Load Ratings : Cr | Not separately recorded | 28.3 kN |
| Basic Load Ratings : C0R | Not separately recorded | 23.2 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 2.65 kN |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 11000 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 13000 min-1 |
| Sd1 | Not separately recorded | - mm |
| B1 | Not separately recorded | - mm |
| B2 | Not separately recorded | - mm |
| Da(Min.) | Not separately recorded | - mm |
| Db(Min.) | Not separately recorded | 39 mm |
| Db(Max.) | Not separately recorded | 41 mm |
| Dc(Min.) | Not separately recorded | - mm |
| Dd(Min.) | Not separately recorded | - mm |
| Da(Max.) | Not separately recorded | 57 mm |
| Db(Max.) | Not separately recorded | - mm |
| Db(Min.) | Not separately recorded | - mm |
| Ra(Max.) | Not separately recorded | 1 mm |
| Rb(Max.) | Not separately recorded | 0.5 mm |
| Mass(Refer.) | Not separately recorded | 0.182 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| NSKNU1007Cylindrical roller bearing |
| 27.8 kN | 23.2 kN | — | — | — |
| KOYONU1007Cylindrical roller bearing |
| 28.3 kN | 23.2 kN | — | 11000 rpmLimiting Speeds(Grease Lub.): 11000 min-1Limiting Speeds(Oil Lub.): 13000 min-1 | 0.182 kg182 g |
| SKFNU 1007 ECPSingle row cylindrical roller bearing, NU design |
| 41.5 kN | 38 kN | 13000 rpm | 13000 rpm | 0.156 kg156 g |
| SKFNU 1007 ECP/C3Single row cylindrical roller bearing, NU design |
| 41.5 kN | 38 kN | 13000 rpm | 13000 rpm | 0.156 kg156 g |
| SKFNU 1007 ECPHSingle row cylindrical roller bearing, NU design |
| 41.5 kN | 38 kN | 13000 rpm | 13000 rpm | 0.153 kg153 g |
| SKFNU 1007 ECPH/HC5C3Hybrid ceramic single row cylindrical roller bearing, NU design |
| 35.8 kN | 38 kN | 15000 rpm | 16000 rpm | 0.149 kg149 g |
| FAGNU1007-XL-M1Cylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.18031 kg180.31 g |
| FAGNU1007-XL-M1-F1-J20AACylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C3Cylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C3-M30AXCylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C3-M32NCylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C4Cylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C4M32IXCylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C5Cylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
| FAGNU1007-XL-M1-F1-J20AA-C5-M32NCylindrical roller bearing |
| 29 kN | 26 kN | 9700 rpm | 22700 rpm | 0.17308 kg173.08 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| NSK NU1007 | Not recorded | Not recorded | Not recorded | Machined brass | Not recorded | Not recorded |
| KOYO NU1007 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF NU 1007 ECP | Without | Not recorded | CN | Non-metallic | Not recorded | None |
| SKF NU 1007 ECP/C3 | Without | Not recorded | C3 | Non-metallic | Not recorded | None |
| SKF NU 1007 ECPH | Without | Not recorded | CN | Non-metallic | Not recorded | None |
| SKF NU 1007 ECPH/HC5C3 | Without | Not recorded | C3 | Non-metallic | Hybrid (ceramic rollers) | None |
| FAG NU1007-XL-M1 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C3 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C3-M30AX | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C3-M32N | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C4 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C4M32IX | Not recorded | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C5 | Not recorded | PN — Normal (ISO 492:2023) | C5 (Group 5) — Internal clearance larger than C4 | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU1007-XL-M1-F1-J20AA-C5-M32N | Not recorded | PN — Normal (ISO 492:2023) | C5 (Group 5) — Internal clearance larger than C4 | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
NU1007
Cylindrical roller bearing
View full technical record →NSKNU1007
Cylindrical roller bearing
View full technical record →SKFNU 1007 ECP
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 1007 ECP/C3
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 1007 ECPH
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 1007 ECPH/HC5C3
Hybrid ceramic single row cylindrical roller bearing, NU design
View full technical record →FAGNU1007-XL-M1
Cylindrical roller bearing
View full technical record →FAGNU1007-XL-M1-F1-J20AA
Cylindrical roller bearing
View full technical record →FAGNU1007-XL-M1-F1-J20AA-C3
Cylindrical roller bearing
View full technical record →FAGNU1007-XL-M1-F1-J20AA-C3-M30AX
Cylindrical roller bearing
View full technical record →FAGNU1007-XL-M1-F1-J20AA-C3-M32N
Cylindrical roller bearing
View full technical record →FAGNU1007-XL-M1-F1-J20AA-C4
Cylindrical roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.