NU 316 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with NU 316. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
NU 316 dimensions and recorded technical data
The recorded NU 316 base designation measures 80×170×39 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from NTN. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 19 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for NU 316
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
NTN NU316 — 24 recorded parameters
Single row cylindrical roller bearings
Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.
For this exact NTN NU316 record, the nominal envelope is 80×170×39 mm (d = internal diameter; D = external diameter; B = bearing/inner ring width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 3.149606×6.692913×1.535433 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Keep the prefix when matching this cylindrical roller bearing. The source construction below, including any axial-load direction statement, belongs only to the complete recorded designation; a similar NU, NJ or NUP number is not an approved substitute.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Dimensions and properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Internal diameter | d | 80 mm |
| External diameter | D | 170 mm |
| Bearing/Inner ring width | B | 39 mm |
| Upper roller diameter | E | 147 mm |
| Under roller diameter | F | 103 mm |
| Min fillet radius | rs | 2.1 mm |
| Min fillet radius | r1s | 2.1 mm |
| Radial clearance class | Not separately recorded | CN |
| Mass | Not separately recorded | 3.86 kg |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dynamic load | C | 211 kN |
| Static load | C0 | 207 kN |
| Fatigue limit load | Cu | 23.7 kN |
| Oil lubrication limit speed | N lim | 4800 r/min |
| Grease lubrication limit speed | N lim | 4100 r/min |
| Min operating temperature | Tmin | -40 °C |
| Max operating temperature | Tmax | 120 °C |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Min shoulder diameter IR | da min | 91 mm |
| Small face shoulder max diameter | da max | 99 mm |
| Min inner ring GO diameter | db min | 105 mm |
| Max shoulder diameter OR | Da max | 159 mm |
| Max fillet radius | ra max | 2 mm |
| Max fillet radius | r1a | 2 mm |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue construction | Not separately recorded | Single row cylindrical roller bearing, floating, separable, pressed steel cage |
| Cage construction | Not separately recorded | pressed steel cage |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| NTNNU316Cylindrical roller bearing |
| 211 kN | 207 kN | — | — | 3.86 kg3860 g |
| SKFNU 316 ECJSingle row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 3.89 kg3890 g |
| SKFNU 316 ECJ/C3Single row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 3.89 kg3890 g |
| SKFNU 316 ECMSingle row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 4.39 kg4390 g |
| SKFNU 316 ECM/C3Single row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 4.39 kg4390 g |
| SKFNU 316 ECM/C3VL0241INSOCOAT single row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 4.39 kg4390 g |
| SKFNU 316 ECMLSingle row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 7500 rpm | 4.35 kg4350 g |
| SKFNU 316 ECML/C4Single row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 7500 rpm | 4.35 kg4350 g |
| SKFNU 316 ECPSingle row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 3.86 kg3860 g |
| SKFNU 316 ECP/C3Single row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 3.94 kg3940 g |
| SKFNU 316 ECPHSingle row cylindrical roller bearing, NU design |
| 300 kN | 290 kN | 4300 rpm | 5000 rpm | 3.86 kg3860 g |
| FAGNU316-E-XL-M1Cylindrical roller bearing |
| 300 kN | 275 kN | 4100 rpm | 7200 rpm | 4.37 kg4370 g |
| FAGNU316-E-XL-TVP2Cylindrical roller bearing |
| 300 kN | 275 kN | 4100 rpm | 5500 rpm | 3.812 kg3812 g |
| TIMKENNU316EJCylindrical roller bearing |
| 290 kN | 289 kN | — | — | 3.9 kg3900 g |
| TIMKENNU316EJC3Cylindrical roller bearing |
| 290 kN | 289 kN | — | — | 3.9 kg3900 g |
| TIMKENNU316EMACylindrical roller bearing |
| 290 kN | 289 kN | — | — | 4.3 kg4300 g |
| TIMKENNU316EMAC3Cylindrical roller bearing |
| 290 kN | 289 kN | — | — | 4.3 kg4300 g |
| NSKNU316EMCylindrical roller bearing |
| 315 kN | 282 kN | — | — | — |
| KOYONU316RCylindrical roller bearing |
| 320 kN | 282 kN | — | 3500 rpmLimiting Speeds(Grease Lub.): 3500 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 4 kg4000 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| NTN NU316 | Not recorded | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
| SKF NU 316 ECJ | Without | Not recorded | CN | Sheet metal | Not recorded | None |
| SKF NU 316 ECJ/C3 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF NU 316 ECM | Without | Not recorded | CN | Machined brass | Not recorded | None |
| SKF NU 316 ECM/C3 | Without | Not recorded | C3 | Machined brass | Not recorded | None |
| SKF NU 316 ECM/C3VL0241 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF NU 316 ECML | Without | Not recorded | CN | Machined brass | Not recorded | None |
| SKF NU 316 ECML/C4 | Without | Not recorded | C4 | Machined brass | Not recorded | None |
| SKF NU 316 ECP | Without | Not recorded | CN | Non-metallic | Not recorded | None |
| SKF NU 316 ECP/C3 | Without | Not recorded | C3 | Non-metallic | Not recorded | None |
| SKF NU 316 ECPH | Without | Not recorded | CN | Non-metallic | Not recorded | None |
| FAG NU316-E-XL-M1 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG NU316-E-XL-TVP2 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | TVP2 — Solid Window Cage made from PA66 | Not recorded | Not recorded |
| TIMKEN NU316EJ | Open | Not recorded | Not recorded | Window Steel cage | Not recorded | Not recorded |
| TIMKEN NU316EJC3 | Open | Not recorded | Not recorded | Window Steel cage | Not recorded | Not recorded |
| TIMKEN NU316EMA | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| TIMKEN NU316EMAC3 | Open | Not recorded | Not recorded | Window Brass cage | Not recorded | Not recorded |
| NSK NU316EM | Not recorded | Not recorded | Not recorded | Machined brass | Not recorded | Not recorded |
| KOYO NU316R | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
NU316
Cylindrical roller bearing
View full technical record →SKFNU 3164 ECMA/C3
Single row cylindrical roller bearing, NU design
View full technical record →FAGNU3164-E-M1A-C3
Cylindrical roller bearing
View full technical record →TIMKENNU3164EMAC3
Cylindrical roller bearing
View full technical record →SKFNU 3168 ECMA
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECJ
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECJ/C3
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECM
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECM/C3
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECM/C3VL0241
INSOCOAT single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECML
Single row cylindrical roller bearing, NU design
View full technical record →SKFNU 316 ECML/C4
Single row cylindrical roller bearing, NU design
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.