NKIS30 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with NKIS30. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
NKIS30 dimensions and recorded technical data
The recorded NKIS30 base designation measures 30×52×22 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 4 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for NKIS30
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
INA NKIS30 — 13 recorded parameters
Needle roller bearing
Reference: Schaeffler medias — INA; source snapshot 2026-09-02.
Under-roller diameter Fw, shaft raceway dimensions and an inner-ring bore are not interchangeable labels. Check whether an inner ring is included in the exact construction.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore Diameter (D) | Not separately recorded | 30 mm |
| Outside Diamater (D) | Not separately recorded | 52 mm |
| Total Width (B) | Not separately recorded | 22 mm |
| Basic Dynamic Load Rating, Radial (Cr) | Not separately recorded | 36,500 N |
| Basic Static Load Rating, Radial (C0R) | Not separately recorded | 50,000 N |
| Raceway Diameter Inner Ring (F) | Not separately recorded | 37 mm |
| Operating Temperature Min. (Tmin) | Not separately recorded | -30 °C |
| Operating Temperature Max. (Tmax) | Not separately recorded | 120 °C |
| Limiting Speed (Limiting Spe) | Not separately recorded | 11,700 1/min |
| Reference Speed (Nϑr) | Not separately recorded | 6,400 1/min |
| Axial Displacement (S) | Not separately recorded | 1 mm |
| Minimum Chamfer Dimension (Rmin) | Not separately recorded | 0.6 mm |
| Fatigue Load Limit, Radial (Cur) | Not separately recorded | 7,000 N |
SKF NKIS 30 — 37 recorded parameters
Single row needle roller bearing with machined rings, with flanges
Reference: SKF product catalogue; source snapshot 2026-09-02.
This can be a unit or housing record. Bolt spacing, housing envelope, centre height and the insert identity need separate checks; do not interpret every outside dimension as bearing D.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 30.0 mm |
| Outside diameter | Not separately recorded | 52.0 mm |
| Width | Not separately recorded | 22.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 42.5 kN |
| Basic static load rating | Not separately recorded | 54.0 kN |
| Reference speed | Not separately recorded | 10000.0 r/min |
| Limiting speed | Not separately recorded | 12000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Complete bearing |
| Number of rows | Not separately recorded | 1 |
| Outer ring type | Not separately recorded | Machined (solid) |
| Aligning feature | Not separately recorded | Without |
| Cage | Not separately recorded | Sheet metal |
| Number of flanges, outer ring | Not separately recorded | 2 |
| Radial internal clearance | Not separately recorded | CN |
| Tolerance class | Not separately recorded | Normal |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | With |
| Indicative carbon footprint for new product | Not separately recorded | 0.68 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.184 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 30 mm |
| Outside diameter | D | 52 mm |
| Width | B | 22 mm |
| Raceway diameter inner ring | F | 37 mm |
| Chamfer dimension outer ring | r 1,2 | min. 0.6 mm |
| Permissible axial displacement from the normal position of one bearing ring relative to the other | s | max. 1 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Smallest permissible abutment diameter shaft, bearings with flanges | d a | min. 34 mm |
| Diameter of housing abutment | D a | max. 48 mm |
| Fillet radius | r a | max. 0.6 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 42.5 kN |
| Basic static load rating | C 0 | 54 kN |
| Fatigue load limit | P u | 6.8 kN |
| Reference speed | Not separately recorded | 10000 r/min |
| Limiting speed | Not separately recorded | 12000 r/min |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKFNKIS 30Single row needle roller bearing with machined rings, with flanges |
| 42.5 kN | 54 kN | 10000 rpm | 12000 rpm | 0.184 kg184 g |
| INANKIS30Needle roller bearing |
| 36.5 kN | 50 kN | 6400 rpm | 11700 rpm | 0.189 kg189 g |
| INANKIS30-C2Needle roller bearing |
| 36.5 kN | 50 kN | 6400 rpm | 11700 rpm | 0.189 kg189 g |
| INANKIS30-C3Needle roller bearing |
| 36.5 kN | 50 kN | 6400 rpm | 11700 rpm | 0.189 kg189 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF NKIS 30 | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| INA NKIS30 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA NKIS30-C2 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA NKIS30-C3 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.