Find · understand · compare

NJ 310 bearing dimensions & suffix variants

Look up recorded dimensions for designations beginning with NJ 310. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.

On this page5 sections

Find by measured dimensions

Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.

Exact model evidence

NJ 310 dimensions and recorded technical data

The recorded NJ 310 base designation measures 50×110×27 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from NTN. It does not assign the same dimensions or operating ratings to every suffix.

The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 19 recorded variants are listed. A dash means the value is missing, not zero.

Exact designation reference

Catalogue parameters for NJ 310

Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.

Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.

NTN NJ310

NTN NJ310 — 24 recorded parameters

Single row cylindrical roller bearings

Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.

For this exact NTN NJ310 record, the nominal envelope is 50×110×27 mm (d = internal diameter; D = external diameter; B = bearing/inner ring width). These are bearing or washer dimensions, not shaft/housing fit limits.

Calculated inch equivalent: 1.968504×4.330709×1.062992 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.

Keep the prefix when matching this cylindrical roller bearing. The source construction below, including any axial-load direction statement, belongs only to the complete recorded designation; a similar NU, NJ or NUP number is not an approved substitute.

Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.

Dimensions and properties

Parameter	Source symbol	Recorded value
Internal diameter	d	50 mm
External diameter	D	110 mm
Bearing/Inner ring width	B	27 mm
Upper roller diameter	E	95 mm
Under roller diameter	F	65 mm
IR flange outer diameter	d1	71 mm
Min fillet radius	rs	2 mm
Min fillet radius	r1s	2 mm
Radial clearance class	Not separately recorded	CN
Mass	Not separately recorded	1.19 kg

Performance

Parameter	Source symbol	Recorded value
Dynamic load	C	96.5 kN
Static load	C0	86 kN
Fatigue limit load	Cu	10.5 kN
Oil lubrication limit speed	N lim	7700 r/min
Grease lubrication limit speed	N lim	6500 r/min
Min operating temperature	Tmin	-40 °C
Max operating temperature	Tmax	120 °C

Mounting dimensions

Parameter	Source symbol	Recorded value
Min shoulder diameter IR	da min	59 mm
Small face shoulder max diameter	da max	63 mm
Min inner ring GO diameter	dc min	73 mm
Max shoulder diameter OR	Da max	101 mm
Max fillet radius	ra max	2 mm

Product characteristics

Parameter	Source symbol	Recorded value
Catalogue construction	Not separately recorded	Single row cylindrical roller bearing, single direction for axial loads, separable, pressed steel cage.
Cage construction	Not separately recorded	pressed steel cage.

Open NTN NJ310 product record →

Clearance tables →Precision classes →Load calculations →Interchange checks →

Brand / full designation	Named dimensions (mm / in)	Dynamic C (kN)	Static C0 (kN)	Reference speed (rpm)	Limiting speed (rpm)	Mass (kg / g)
NTNNJ310Cylindrical roller bearing	Internal diameter (d) 50 mm 1.968504 in External diameter (D) 110 mm 4.330709 in Bearing/Inner ring width (B) 27 mm 1.062992 in	96.5 kN	86 kN	—	—	1.19 kg1190 g
SKFNJ 310 ECJSingle row cylindrical roller bearing, NJ design	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.18 kg1180 g
SKFNJ 310 ECJ/C3Single row cylindrical roller bearing, NJ design	Recorded bore (d) 50 mm 1.968504 in Recorded outside dimension (D) 110 mm 4.330709 in Catalogue width (symbol unverified) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.18 kg1180 g
SKFNJ 310 ECMSingle row cylindrical roller bearing, NJ design	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.34 kg1340 g
SKFNJ 310 ECM/C3Single row cylindrical roller bearing, NJ design	Recorded bore (d) 50 mm 1.968504 in Recorded outside dimension (D) 110 mm 4.330709 in Catalogue width (symbol unverified) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.34 kg1340 g
SKFNJ 310 ECM/C4Single row cylindrical roller bearing, NJ design	Recorded bore (d) 50 mm 1.968504 in Recorded outside dimension (D) 110 mm 4.330709 in Catalogue width (symbol unverified) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.34 kg1340 g
SKFNJ 310 ECMLSingle row cylindrical roller bearing, NJ design	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	12000 rpm	1.35 kg1350 g
SKFNJ 310 ECPSingle row cylindrical roller bearing, NJ design	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.17 kg1170 g
SKFNJ 310 ECP/C3Single row cylindrical roller bearing, NJ design	Recorded bore (d) 50 mm 1.968504 in Recorded outside dimension (D) 110 mm 4.330709 in Catalogue width (symbol unverified) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.17 kg1170 g
SKFNJ 310 ECP/C4Single row cylindrical roller bearing, NJ design	Recorded bore (d) 50 mm 1.968504 in Recorded outside dimension (D) 110 mm 4.330709 in Catalogue width (symbol unverified) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.17 kg1170 g
SKFNJ 310 ECPHSingle row cylindrical roller bearing, NJ design	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	127 kN	112 kN	6700 rpm	8000 rpm	1.17 kg1170 g
FAGNJ310-E-XL-M1Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	11600 rpm	1.447 kg1447 g
FAGNJ310-E-XL-M1-C3Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	11600 rpm	1.447 kg1447 g
FAGNJ310-E-XL-M1-C4Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	11600 rpm	1.31 kg1310 g
FAGNJ310-E-XL-TVP2Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	8900 rpm	1.147 kg1147 g
FAGNJ310-E-XL-TVP2-C3Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	8900 rpm	1.16 kg1160 g
FAGNJ310-E-XL-TVP2-C4Cylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	131 kN	114 kN	6000 rpm	8900 rpm	1.16 kg1160 g
NSKNJ310EWCylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Bearing width (B) 27 mm 1.062992 in	135 kN	113 kN	—	—	—
KOYONJ310RCylindrical roller bearing	Bore diameter (d) 50 mm 1.968504 in Outside diameter (D) 110 mm 4.330709 in Width (B) 27 mm 1.062992 in	138 kN	113 kN	—	5500 rpmLimiting Speeds(Grease Lub.): 5500 min-1Limiting Speeds(Oil Lub.): 7400 min-1	1.2 kg1200 g

Compare recorded seals, clearance, precision and materials

Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.

Brand / designation	Closure	Original precision	Clearance	Cage	Material	Lubricant
NTN NJ310	Not recorded	Not recorded	CN	pressed steel cage.	Not recorded	Not recorded
SKF NJ 310 ECJ	Without	Not recorded	CN	Sheet metal	Not recorded	None
SKF NJ 310 ECJ/C3	Without	Not recorded	C3	Sheet metal	Not recorded	None
SKF NJ 310 ECM	Without	Not recorded	CN	Machined brass	Not recorded	None
SKF NJ 310 ECM/C3	Without	Not recorded	C3	Machined brass	Not recorded	None
SKF NJ 310 ECM/C4	Without	Not recorded	C4	Machined brass	Not recorded	None
SKF NJ 310 ECML	Without	Not recorded	CN	Machined brass	Not recorded	None
SKF NJ 310 ECP	Without	Not recorded	CN	Non-metallic	Not recorded	None
SKF NJ 310 ECP/C3	Without	Not recorded	C3	Non-metallic	Not recorded	None
SKF NJ 310 ECP/C4	Without	Not recorded	C4	Non-metallic	Not recorded	None
SKF NJ 310 ECPH	Without	Not recorded	CN	Non-metallic	Not recorded	None
FAG NJ310-E-XL-M1	Not recorded	PN — Normal (ISO 492:2023)	CN (Group N) — Normal internal clearance	M1 — Two Piece Brass Cage Roller Guided	Not recorded	Not recorded
FAG NJ310-E-XL-M1-C3	Not recorded	PN — Normal (ISO 492:2023)	C3 (Group 3) — Internal clearance larger than CN	M1 — Two Piece Brass Cage Roller Guided	Not recorded	Not recorded
FAG NJ310-E-XL-M1-C4	Not recorded	PN — Normal (ISO 492:2023)	C4 (Group 4) — Internal clearance larger than C3	M1 — Two Piece Brass Cage Roller Guided	Not recorded	Not recorded
FAG NJ310-E-XL-TVP2	Not recorded	PN — Normal (ISO 492:2023)	CN (Group N) — Normal internal clearance	TVP2 — Solid Window Cage made from PA66	Not recorded	Not recorded
FAG NJ310-E-XL-TVP2-C3	Not recorded	PN — Normal (ISO 492:2023)	C3 (Group 3) — Internal clearance larger than CN	TVP2 — Solid Window Cage made from PA66	Not recorded	Not recorded
FAG NJ310-E-XL-TVP2-C4	Not recorded	PN — Normal (ISO 492:2023)	C4 (Group 4) — Internal clearance larger than C3	TVP2 — Solid Window Cage made from PA66	Not recorded	Not recorded
NSK NJ310EW	Not recorded	Not recorded	Not recorded	Pressed steel	Not recorded	Not recorded
KOYO NJ310R	Not recorded	Not recorded	Not recorded	Not recorded	Not recorded	Not recorded

How to compare these values

Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.

Check load calculations →Estimate rating life →Decode the complete marking →Check replacement evidence →

Related prefix matches — other model numbers may appear

These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.

NTN