N312 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with N312. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
N312 dimensions and recorded technical data
The recorded N312 base designation measures 60×130×31 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 8 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for N312
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO N312 — 26 recorded parameters
Cylindrical roller bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 60 mm |
| D | Not separately recorded | 130 mm |
| B | Not separately recorded | 31 mm |
| R(Min.) | Not separately recorded | 2.1 mm |
| R1(Min.) | Not separately recorded | 2.1 mm |
| Fw | Not separately recorded | - mm |
| Ew | Not separately recorded | 113 mm |
| Basic Load Ratings : Cr | Not separately recorded | 155 kN |
| Basic Load Ratings : C0R | Not separately recorded | 126 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 17.3 kN |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 4700 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 6300 min-1 |
| Sd1 | Not separately recorded | - mm |
| B1 | Not separately recorded | - mm |
| B2 | Not separately recorded | - mm |
| Da(Min.) | Not separately recorded | 71 mm |
| Db(Min.) | Not separately recorded | - mm |
| Db(Max.) | Not separately recorded | - mm |
| Dc(Min.) | Not separately recorded | - mm |
| Dd(Min.) | Not separately recorded | - mm |
| Da(Max.) | Not separately recorded | - mm |
| Db(Max.) | Not separately recorded | 119 mm |
| Db(Min.) | Not separately recorded | 116 mm |
| Ra(Max.) | Not separately recorded | 2 mm |
| Rb(Max.) | Not separately recorded | 2 mm |
| Mass(Refer.) | Not separately recorded | 1.78 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| KOYON312Cylindrical roller bearing |
| 155 kN | 126 kN | — | 4700 rpmLimiting Speeds(Grease Lub.): 4700 min-1Limiting Speeds(Oil Lub.): 6300 min-1 | 1.78 kg1780 g |
| SKFN 312 ECMSingle row cylindrical roller bearing, N design |
| 173 kN | 160 kN | 5600 rpm | 6700 rpm | 2.05 kg2050 g |
| SKFN 312 ECPSingle row cylindrical roller bearing, N design |
| 173 kN | 160 kN | 5600 rpm | 6700 rpm | 1.76 kg1760 g |
| SKFN 312 M/P63Single row cylindrical roller bearing, N design |
| 123 kN | 127 kN | 5600 rpm | 6700 rpm | 1.94 kg1940 g |
| FAGN312-E-XL-M1Cylindrical roller bearing |
| 177 kN | 157 kN | — | — | 2 kg2000 g |
| FAGN312-E-XL-M1-C3Cylindrical roller bearing |
| 177 kN | 157 kN | — | — | 2 kg2000 g |
| FAGN312-E-XL-TVP2Cylindrical roller bearing |
| 177 kN | 157 kN | — | — | 1.78 kg1780 g |
| NSKN312WCylindrical roller bearing |
| 152 kN | 126 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| KOYO N312 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF N 312 ECM | Without | Not recorded | CN | Machined brass | Not recorded | None |
| SKF N 312 ECP | Without | Not recorded | CN | Non-metallic | Not recorded | None |
| SKF N 312 M/P63 | Without | Not recorded | C3 | Machined brass | Not recorded | None |
| FAG N312-E-XL-M1 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG N312-E-XL-M1-C3 | Not recorded | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M1 — Two Piece Brass Cage Roller Guided | Not recorded | Not recorded |
| FAG N312-E-XL-TVP2 | Not recorded | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | TVP2 — Solid Window Cage made from PA66 | Not recorded | Not recorded |
| NSK N312W | Not recorded | Not recorded | Not recorded | Pressed steel | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
N312
Cylindrical roller bearing
View full technical record →SKFN 312 ECM
Single row cylindrical roller bearing, N design
View full technical record →SKFN 312 ECP
Single row cylindrical roller bearing, N design
View full technical record →FAGN312-E-XL-M1
Cylindrical roller bearing
View full technical record →FAGN312-E-XL-M1-C3
Cylindrical roller bearing
View full technical record →FAGN312-E-XL-TVP2
Cylindrical roller bearing
View full technical record →SKFN 312 M/P63
Single row cylindrical roller bearing, N design
View full technical record →NSKN312W
Cylindrical roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.