HK2212 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with HK2212. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
HK2212 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 5 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for HK2212
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO HK2212 — 11 recorded parameters
Needle roller bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Under-roller diameter Fw, shaft raceway dimensions and an inner-ring bore are not interchangeable labels. Check whether an inner ring is included in the exact construction.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Fw | Not separately recorded | 22 mm |
| D | Not separately recorded | 28 mm |
| C | Not separately recorded | 12 mm |
| R(Min.) | Not separately recorded | 1 mm |
| Basic Load Ratings : Cr | Not separately recorded | 9.81 kN |
| Basic Load Ratings : C0R | Not separately recorded | 14.50 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 2.20 kN |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 9600 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 15000 min-1 |
| Mounting Inner Ring | Not separately recorded | JR17x22x13 |
| Mass(Refer.) | Not separately recorded | 0.015 kg |
SKF HK 2212 — 29 recorded parameters
Drawn cup needle roller bearing with open ends
Reference: SKF product catalogue; source snapshot 2026-09-02.
This designation identifies a tapered-bearing component. A cone or cup alone is not the assembled bearing; use the documented pairing and total assembly width before comparing an interchange.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter of needle roller complement | Not separately recorded | 22.0 mm |
| Outside diameter | Not separately recorded | 28.0 mm |
| Width | Not separately recorded | 12.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 8.8 kN |
| Basic static load rating | Not separately recorded | 13.7 kN |
| Reference speed | Not separately recorded | 11000.0 r/min |
| Limiting speed | Not separately recorded | 12000.0 r/min |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Bearing without inner ring |
| Number of rows | Not separately recorded | 1 |
| Outer ring type | Not separately recorded | Drawn cup with open ends |
| Aligning feature | Not separately recorded | Without |
| Cage | Not separately recorded | Sheet steel |
| Number of flanges, outer ring | Not separately recorded | 2 |
| Tolerance class | Not separately recorded | Normal |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.05 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.014 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter under rollers | F w | 22 mm |
| Outside diameter | D | 28 mm |
| Width | C | 12 mm |
| Chamfer dimension drawn cup (outer ring) | r | min. 0.8 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | C | 8.8 kN |
| Basic static load rating | C 0 | 13.7 kN |
| Fatigue load limit | P u | 1.56 kN |
| Reference speed | Not separately recorded | 11000 r/min |
| Limiting speed | Not separately recorded | 12000 r/min |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKFHK 2212Drawn cup needle roller bearing with open ends |
| 8.8 kN | 13.7 kN | 11000 rpm | 12000 rpm | 0.014 kg14 g |
| INAHK2212Drawn cup needle roller bearing open end |
| 9.1 kN | 13.4 kN | 8900 rpm | 11700 rpm | 0.014784 kg14.784 g |
| KOYOHK2212Needle roller bearing |
| 9.81 kN | 14.5 kN | — | 9600 rpmLimiting Speeds(Grease Lub.): 9600 min-1Limiting Speeds(Oil Lub.): 15000 min-1 | 0.015 kg15 g |
| INAHK2212-AS1-BDrawn cup needle roller bearing open end |
| 9.1 kN | 13.4 kN | 8900 rpm | 11700 rpm | 0.014692 kg14.692 g |
| INAHK2212-B-L271Drawn cup needle roller bearing open end |
| 9.1 kN | 13.4 kN | 8900 rpm | 11700 rpm | 0.01523 kg15.23 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF HK 2212 | Without | Not recorded | Not recorded | Sheet steel | Bearing steel | None |
| INA HK2212 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO HK2212 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA HK2212-AS1-B | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA HK2212-B-L271 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
HK2212
Drawn cup needle roller bearing open end
View full technical record →KOYOHK2212
Needle roller bearing
View full technical record →SKFHK 2212
Drawn cup needle roller bearing with open ends
View full technical record →INAHK2212-AS1-B
Drawn cup needle roller bearing open end
View full technical record →INAHK2212-B-L271
Drawn cup needle roller bearing open end
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.