AXK2035 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with AXK2035. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
AXK2035 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 3 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for AXK2035
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO AXK2035 — 25 recorded parameters
Needle roller bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
KOYO AXK2035 is a thrust needle-roller/cage component. Its recorded inner diameter, outer diameter and roller/assembly thickness are 20×35×2 mm. This is the cage-and-roller dimension set, not a complete stack including separate thrust washers.
Calculated inch reference (inner diameter × outer diameter × component thickness): 0.787402 × 1.377953 × 0.07874 in. This converts the recorded millimetres using exactly 25.4 mm/in and rounds to six decimals; it does not change the nominal series or supply machining tolerances.
Keep washer dimensions and part numbers separate from the 2 mm component thickness. A washer added on either side changes the assembled axial stack; its suitability and running surfaces must be verified for the actual arrangement.
Raceway limit symbols are retained as the individual manufacturer labels them. Do not transfer an Ea or Eb value between the SKF and KOYO tables merely because the base designation matches.
Under-roller diameter Fw, shaft raceway dimensions and an inner-ring bore are not interchangeable labels. Check whether an inner ring is included in the exact construction.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dc1 | Not separately recorded | 20 mm |
| Dc | Not separately recorded | 35 mm |
| Dw | Not separately recorded | 2 mm |
| Ea | Not separately recorded | 34.0 mm |
| Eb | Not separately recorded | 22.0 mm |
| Ra(Max.) | Not separately recorded | 0.3 mm |
| Basic Load Ratings Ca | Not separately recorded | 12.8 kN |
| Basic Load Ratings C0A | Not separately recorded | 45.4 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 4.40 kN |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 12000 min-1 |
| (Refer.)Mass | Not separately recorded | 0.006 kg |
| Washer Dimensions : D,D1 | Not separately recorded | 35 mm |
| Washer Dimensions : D1 | Not separately recorded | 21 mm |
| Thin Washer Dimensions : H1 | Not separately recorded | 1.00 mm |
| Thin Washer No. | Not separately recorded | AS2035 |
| Thin (Refer.)Mass | Not separately recorded | 0.005 kg |
| Heavy(Ls) Washer Dimensions : H | Not separately recorded | 2.75 mm |
| Heavy(Ls) Washer Dimensions : A | Not separately recorded | 0.50 mm |
| Heavy(Ls) Washer No. | Not separately recorded | LS2035 |
| Heavy(Ls) (Refer.)Mass | Not separately recorded | 0.014 kg |
| Heavy Washer Dimensions : H | Not separately recorded | 2.75 mm |
| Heavy Washer Dimensions : R(Min.) | Not separately recorded | 0.30 mm |
| Heavy Washer No(Shaft Piloted) | Not separately recorded | WS.81104 |
| Heavy Washer No.(Housing Piloted) | Not separately recorded | GS.81104 |
| Heavy (Refer.)Mass | Not separately recorded | 0.014 kg |
SKF AXK 2035 — 24 recorded parameters
Needle roller and cage thrust assembly
Reference: SKF product catalogue; source snapshot 2026-09-02.
SKF AXK 2035 is a thrust needle-roller/cage component. Its recorded inner diameter, outer diameter and roller/assembly thickness are 20×35×2 mm. This is the cage-and-roller dimension set, not a complete stack including separate thrust washers.
Calculated inch reference (inner diameter × outer diameter × component thickness): 0.787402 × 1.377953 × 0.07874 in. This converts the recorded millimetres using exactly 25.4 mm/in and rounds to six decimals; it does not change the nominal series or supply machining tolerances.
Keep washer dimensions and part numbers separate from the 2 mm component thickness. A washer added on either side changes the assembled axial stack; its suitability and running surfaces must be verified for the actual arrangement.
Raceway limit symbols are retained as the individual manufacturer labels them. Do not transfer an Ea or Eb value between the SKF and KOYO tables merely because the base designation matches.
Under-roller diameter Fw, shaft raceway dimensions and an inner-ring bore are not interchangeable labels. Check whether an inner ring is included in the exact construction.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 20.0 mm |
| Outside diameter | Not separately recorded | 35.0 mm |
| Height | Not separately recorded | 2.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 12.0 kN |
| Basic static load rating | Not separately recorded | 47.5 kN |
| Reference speed | Not separately recorded | 4300.0 r/min |
| Limiting speed | Not separately recorded | 8500.0 r/min |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Needle roller and cage assembly |
| Cage | Not separately recorded | Sheet steel |
| Roller grade | Not separately recorded | G2 |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.02 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.0056 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 20 mm |
| Outside diameter | D | 35 mm |
| Diameter roller | D w | 2 mm |
| Raceway diameter (min.) roller and cage thrust assembly | E a | min. 22 mm |
| Raceway diameter (max.) roller and cage thrust assembly | E b | max. 34 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | C | 12 kN |
| Basic static load rating | C 0 | 47.5 kN |
| Fatigue load limit | P u | 5.6 kN |
| Reference speed | Not separately recorded | 4300 r/min |
| Limiting speed | Not separately recorded | 8500 r/min |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKFAXK 2035Needle roller and cage thrust assembly |
| 12 kN | 47.5 kN | 4300 rpm | 8500 rpm | 0.0056 kg5.6 g |
| KOYOAXK2035Needle roller bearing |
| — | — | — | 12000 rpmLimiting Speeds(Oil Lub.): 12000 min-1 | 0.006 kg6 g |
| INAAXK2035-A/0-10Axial needle roller and cage assembly |
| — | — | 4350 rpm | 10500 rpm | 0.0054 kg5.4 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF AXK 2035 | Not recorded | Not recorded | Not recorded | Sheet steel | Bearing steel | Not recorded |
| KOYO AXK2035 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA AXK2035-A/0-10 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.