6802 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6802. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6802 dimensions and recorded technical data
The recorded 6802 base designation measures 15×24×5 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from NSK, KOYO, NACHI, NTN, EZO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 19 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| NSK6802Deep groove ball bearing |
| 2.28 kN | 1.26 kN | — | — | 0.007 kg7 g |
| KOYO6802Deep groove ball bearing |
| 2.6 kN | 1.25 kN | — | 28000 rpmLimiting Speeds(Grease Lub.): 28000 min-1Limiting Speeds(Oil Lub.): 33000 min-1 | 0.007 kg7 g |
| NACHI6802Deep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | 0.007 kg7 g |
| NTN6802Deep groove ball bearing |
| 2.3 kN | 1.26 kN | — | — | 0.007 kg7 g |
| EZO6802Deep groove ball bearing |
| 2.07 kN | 1.26 kN | — | — | 0.00628 kg6.28 g |
| NSK6802DDDeep groove ball bearing |
| 2.28 kN | 1.26 kN | — | — | — |
| NSK6802VVDeep groove ball bearing |
| 2.28 kN | 1.26 kN | — | — | — |
| NSK6802ZZDeep groove ball bearing |
| 2.28 kN | 1.26 kN | — | — | — |
| KOYO6802 2RSDeep groove ball bearing |
| 2.6 kN | 1.25 kN | — | 16000 rpmLimiting Speeds(Grease Lub.): 16000 min-1 | 0.007 kg7 g |
| KOYO6802 2RUDeep groove ball bearing |
| 2.6 kN | 1.25 kN | — | 28000 rpmLimiting Speeds(Grease Lub.): 28000 min-1 | 0.007 kg7 g |
| KOYO6802 ZZDeep groove ball bearing |
| 2.6 kN | 1.25 kN | — | 28000 rpmLimiting Speeds(Grease Lub.): 28000 min-1 | 0.007 kg7 g |
| NACHI6802-2NKEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| NACHI6802-2NSEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| NACHI6802NKEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| NACHI6802NSEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| NACHI6802ZEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| NACHI6802ZZEDeep groove ball bearing |
| 2.61 kN | 1.26 kN | — | — | — |
| EZO6802 2RSDeep groove ball bearing |
| 2.07 kN | 1.26 kN | — | — | 0.00706 kg7.06 g |
| EZO6802ZZDeep groove ball bearing |
| 2.07 kN | 1.26 kN | — | — | 0.00669 kg6.69 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| NSK 6802 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6802 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN 6802 | open | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
| EZO 6802 | Open (no closure suffix in this catalogue marking) | Not recorded | Not recorded | Not recorded | High-carbon chromium bearing steel | Not recorded |
| NSK 6802DD | Contact-sealed DD catalogue type | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6802VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6802ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6802 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6802 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6802 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802-2NKE | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802-2NSE | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802NKE | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802NSE | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6802ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| EZO 6802 2RS | Two contact rubber seals | Not recorded | Not recorded | Not recorded | High-carbon chromium bearing steel | Not recorded |
| EZO 6802ZZ | Two pressed-steel shields | Not recorded | Not recorded | Not recorded | High-carbon chromium bearing steel | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6802
Deep groove ball bearing
View full technical record →NTN6802
Deep groove ball bearing
View full technical record →NSK6802
Deep groove ball bearing
View full technical record →NACHI6802
Deep groove ball bearing
View full technical record →EZO6802
Deep groove ball bearing
View full technical record →NACHI6802-2NKE
Deep groove ball bearing
View full technical record →NACHI6802-2NSE
Deep groove ball bearing
View full technical record →KOYO6802 2RS
Deep groove ball bearing
View full technical record →EZO6802 2RS
Deep groove ball bearing
View full technical record →KOYO6802 2RU
Deep groove ball bearing
View full technical record →TIMKEN680235 / 680270
Tapered roller bearing
View full technical record →TIMKEN680235-90015
Tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.