6405 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6405. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6405 dimensions and recorded technical data
The recorded 6405 base designation measures 25×80×21 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 10 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6405
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6405 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 80 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 21 mm |
| Deviation limits of ring width | t ΔBs | -0.12 to 0 mm |
| Shoulder diameter | d 1 | ≈ 45.42 mm |
| Shoulder diameter | D 1 | ≈ 62.9 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 34 mm |
| Diameter of housing abutment | D a | max. 71 mm |
| Radius of shaft or housing fillet | r a | max. 1.5 mm |
FAG 6405 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Outside diameter | D | 80 mm |
| Width | B | 21 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 65.6 mm |
| Caliber diameter outer ring | D2 | 67.6 mm |
| Shoulder diameter inner ring | d1 | 49.3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 36 mm |
| Maximum diameter of housing shoulder | Da max | 69 mm |
| Maximum fillet radius | ra max | 1.5 mm |
KOYO 6405 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Outside diameter | D | 80 mm |
| Width | B | 21 mm |
TIMKEN 6405 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 25 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 21 mm / 0.827 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6405Deep groove ball bearing |
| 35.8 kN | 19.3 kN | 20000 rpm | 13000 rpm | 0.53 kg530 g |
| FAG6405Deep groove ball bearing |
| 35.5 kN | 19.1 kN | 9400 rpm | 12300 rpm | 0.523 kg523 g |
| TIMKEN6405Deep groove ball bearing |
| 37.2 kN | 18.8 kN | — | — | 0.53 kg530 g |
| KOYO6405Deep groove ball bearing |
| 45.2 kN | 19.4 kN | — | 9100 rpmLimiting Speeds(Grease Lub.): 9100 min-1Limiting Speeds(Oil Lub.): 11000 min-1 | 0.53 kg530 g |
| SKF6405/C3Deep groove ball bearing |
| 35.8 kN | 19.3 kN | 20000 rpm | 13000 rpm | 0.53 kg530 g |
| FAG6405-2ZDeep groove ball bearing |
| 35.5 kN | 19.1 kN | 9400 rpm | 10500 rpm | 0.541 kg541 g |
| FAG6405-C-2Z>VDeep groove ball bearing |
| 38.5 kN | 19.1 kN | 9700 rpm | 11500 rpm | 0.528 kg528 g |
| TIMKEN6405-C3Deep groove ball bearing |
| 37.2 kN | 18.8 kN | — | — | 0.53 kg530 g |
| TIMKEN6405-NRDeep groove ball bearing |
| 37.2 kN | 18.8 kN | — | — | 0.53 kg530 g |
| TIMKEN6405/VSL609Deep groove ball bearing |
| 37.2 kN | 18.8 kN | — | — | 0.53 kg530 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6405 | Without | Normal | CN | Sheet metal | Bearing steel | None |
| FAG 6405 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6405 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 6405 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6405/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6405-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6405-C-2Z>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| TIMKEN 6405-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6405-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6405/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6405
Deep groove ball bearing
View full technical record →FAG6405
Deep groove ball bearing
View full technical record →TIMKEN6405
Deep groove ball bearing
View full technical record →KOYO6405
Deep groove ball bearing
View full technical record →FAG6405-2Z
Deep groove ball bearing
View full technical record →FAG6405-C-2Z>V
Deep groove ball bearing
View full technical record →SKF6405/C3
Deep groove ball bearing
View full technical record →TIMKEN6405-C3
Deep groove ball bearing
View full technical record →TIMKEN6405-NR
Deep groove ball bearing
View full technical record →TIMKEN6405/VSL609
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.