6319 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6319. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6319 dimensions and recorded technical data
The recorded 6319 base designation measures 95×200×45 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 67 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6319
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6319/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 95.0 mm |
| Outside diameter | Not supplied separately | 200.0 mm |
| Width | Not supplied separately | 45.0 mm |
SKF 6319 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.015 to 0 mm |
| Outside diameter | D | 200 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.02 to 0 mm |
| Width | B | 45 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 127.7 mm |
| Recess diameter | D 2 | ≈ 171.9 mm |
| Chamfer dimension | r 1,2 | min. 3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 109 mm |
| Diameter of housing abutment | D a | max. 186 mm |
| Radius of shaft or housing fillet | r a | max. 2.5 mm |
FAG 6319 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Outside diameter | D | 200 mm |
| Width | B | 45 mm |
| Minimum chamfer dimension | rmin | 3 mm |
| Shoulder diameter outer ring | D1 | 166.88 mm |
| Shoulder diameter inner ring | d1 | 129.08 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 109 mm |
| Maximum diameter of housing shoulder | Da max | 186 mm |
| Maximum fillet radius | ra max | 2.5 mm |
FAG 6319-C3 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Outside diameter | D | 200 mm |
| Width | B | 45 mm |
| Minimum chamfer dimension | rmin | 3 mm |
| Shoulder diameter outer ring | D1 | 166.88 mm |
| Shoulder diameter inner ring | d1 | 129.08 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 109 mm |
| Maximum diameter of housing shoulder | Da max | 186 mm |
| Maximum fillet radius | ra max | 2.5 mm |
KOYO 6319 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Outside diameter | D | 200 mm |
| Width | B | 45 mm |
TIMKEN 6319 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 95 mm |
| O.D. (D) | D | 200 mm / 7.874 in |
| Width (B) | B | 45 mm / 1.772 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 3 mm / 0.118 in |
TIMKEN 6319-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 95 mm |
| O.D. (D) | D | 200 mm / 7.874 in |
| Width (B) | B | 45 mm / 1.772 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 3 mm / 0.118 in |
Catalogue parameters for 6319
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 6319/C3 — 21 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
SKF 6319/C3 initial radial clearance: 30–58 µm (0.030–0.058 mm), obtained from SKF Rolling bearings, Table 6 (printed page 252). This is a catalogue-table lookup for the recorded 95 mm cylindrical bore and C3 class, not a measurement of an individual bearing.
The applicable diameter band is 80 < d ≤ 100 mm. In the same SKF table the Normal interval is 12–36 µm; C3 is a larger-clearance class, not an accuracy grade. The overlapping endpoints do not turn the classes into identical specifications.
This range describes the unmounted bearing without measuring load. Fits, ring temperatures and service conditions determine the installed and operating clearance. It is not a shaft tolerance or a recommended running gap.
The numeric lookup here is explicitly for the SKF single-row deep-groove construction without filling slots. The neighbouring FAG and KOYO records must retain their own manufacturer evidence; a common 6319 base does not transfer this value automatically.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 95.0 mm |
| Outside diameter | Not separately recorded | 200.0 mm |
| Width | Not separately recorded | 45.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 159.0 kN |
| Basic static load rating | Not separately recorded | 118.0 kN |
| Reference speed | Not separately recorded | 7000.0 r/min |
| Limiting speed | Not separately recorded | 4500.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | C3 |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 20.9 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 5.65 kg |
SKF 6319 — 45 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 95.0 mm |
| Outside diameter | Not separately recorded | 200.0 mm |
| Width | Not separately recorded | 45.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 159.0 kN |
| Basic static load rating | Not separately recorded | 118.0 kN |
| Reference speed | Not separately recorded | 7000.0 r/min |
| Limiting speed | Not separately recorded | 4500.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 20.9 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 5.65 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.015 to 0 mm |
| Outside diameter | D | 200 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.02 to 0 mm |
| Width | B | 45 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 127.7 mm |
| Recess diameter | D 2 | ≈ 171.9 mm |
| Chamfer dimension | r 1,2 | min. 3 mm |
| ISO tolerance class for dimensions | Not separately recorded | P6 and tighter width tolerance |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 109 mm |
| Diameter of housing abutment | D a | max. 186 mm |
| Radius of shaft or housing fillet | r a | max. 2.5 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 159 kN |
| Basic static load rating | C 0 | 118 kN |
| Fatigue load limit | P u | 4.15 kN |
| Reference speed | Not separately recorded | 7000 r/min |
| Limiting speed | Not separately recorded | 4500 r/min |
| Minimum load factor | k r | 0.03 |
| Calculation factor | f 0 | 13.3 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 25 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 50 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | Normal |
FAG 6319 — 46 recorded parameters
Deep groove ball bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Bore diameter | d | 3.74 in |
| Outside diameter | D | 200 mm |
| Outside diameter | D | 7.874 in |
| Width | B | 45 mm |
| Width | B | 1.772 in |
| Basic dynamic load rating, radial | Cr | 154,000 N |
| Basic dynamic load rating, radial | Cr | 34,622.302 lbf |
| Basic static load rating, radial | C0r | 113,000 N |
| Basic static load rating, radial | C0r | 25,404.676 lbf |
| Fatigue load limit, radial | Cur | 6,600 N |
| Fatigue load limit, radial | Cur | 1,483.813 lbf |
| Limiting speed | nG | 4,600 1/min |
| Reference speed | nϑr | 4,950 1/min |
| Mass | ≈m | 6.23 kg |
| Mass | ≈m | 13.735 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 109 mm |
| Minimum diameter shaft shoulder | da min | 4.291 in |
| Maximum diameter of housing shoulder | Da max | 186 mm |
| Maximum diameter of housing shoulder | Da max | 7.323 in |
| Maximum fillet radius | ra max | 2.5 mm |
| Maximum fillet radius | ra max | 0.098 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension | rmin | 3 mm |
| Minimum chamfer dimension | rmin | 0.118 in |
| Shoulder diameter outer ring | D1 | 166.88 mm |
| Shoulder diameter outer ring | D1 | 6.57 in |
| Shoulder diameter inner ring | d1 | 129.08 mm |
| Shoulder diameter inner ring | d1 | 5.082 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 150 °C |
| Operating temperature max. | Tmax | 302 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Calculation factor | f0 | 13.8 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Type of Seal | Without | Not sealed |
| Cage | JN | Steel sheet metal |
| Tolerance class | PN | Normal (ISO 492:2023) |
| Dimensional / heat stabilization | S0 | Rings dimensional stabilized up to 150° |
| Lubricant | Without | Bearing not greased |
| Radial internal clearance | CN (Group N) | Normal internal clearance |
| Bore type | Z | Cylindrical |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Axial load capacity in both directions | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
FAG 6319-C3 — 46 recorded parameters
Deep groove ball bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 95 mm |
| Bore diameter | d | 3.74 in |
| Outside diameter | D | 200 mm |
| Outside diameter | D | 7.874 in |
| Width | B | 45 mm |
| Width | B | 1.772 in |
| Basic dynamic load rating, radial | Cr | 154,000 N |
| Basic dynamic load rating, radial | Cr | 34,622.302 lbf |
| Basic static load rating, radial | C0r | 113,000 N |
| Basic static load rating, radial | C0r | 25,404.676 lbf |
| Fatigue load limit, radial | Cur | 6,600 N |
| Fatigue load limit, radial | Cur | 1,483.813 lbf |
| Limiting speed | nG | 4,600 1/min |
| Reference speed | nϑr | 4,950 1/min |
| Mass | ≈m | 6.039 kg |
| Mass | ≈m | 13.314 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 109 mm |
| Minimum diameter shaft shoulder | da min | 4.291 in |
| Maximum diameter of housing shoulder | Da max | 186 mm |
| Maximum diameter of housing shoulder | Da max | 7.323 in |
| Maximum fillet radius | ra max | 2.5 mm |
| Maximum fillet radius | ra max | 0.098 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension | rmin | 3 mm |
| Minimum chamfer dimension | rmin | 0.118 in |
| Shoulder diameter outer ring | D1 | 166.88 mm |
| Shoulder diameter outer ring | D1 | 6.57 in |
| Shoulder diameter inner ring | d1 | 129.08 mm |
| Shoulder diameter inner ring | d1 | 5.082 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 150 °C |
| Operating temperature max. | Tmax | 302 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Calculation factor | f0 | 13.8 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Type of Seal | Without | Not sealed |
| Cage | JN | Steel sheet metal |
| Tolerance class | PN | Normal (ISO 492:2023) |
| Dimensional / heat stabilization | S0 | Rings dimensional stabilized up to 150° |
| Lubricant | Without | Bearing not greased |
| Radial internal clearance | C3 (Group 3) | Internal clearance larger than CN |
| Bore type | Z | Cylindrical |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Axial load capacity in both directions | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
KOYO 6319 — 14 recorded parameters
Deep groove ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 95 mm |
| D | Not separately recorded | 200 mm |
| B | Not separately recorded | 45 mm |
| R(Min.) | Not separately recorded | 3 mm |
| Basic Load Ratings : Cr | Not separately recorded | 191 kN |
| Basic Load Ratings : C0R | Not separately recorded | 119 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 9.45 kN |
| Factor : F0 | Not separately recorded | 13.3 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 3300 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 4000 min-1 |
| Da(Min.) | Not separately recorded | 108 mm |
| Da(Max.) | Not separately recorded | 187 mm |
| Ra(Max.) | Not separately recorded | 2.5 mm |
| Mass(Refer.) | Not separately recorded | 5.67 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6319Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.65 kg5650 g |
| FAG6319Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6.23 kg6230 g |
| TIMKEN6319Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| NSK6319Deep groove ball bearing |
| 168 kN | 119 kN | — | — | 5.76 kg5760 g |
| KOYO6319Deep groove ball bearing |
| 191 kN | 119 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1Limiting Speeds(Oil Lub.): 4000 min-1 | 5.67 kg5670 g |
| SKF6319-2RS1Deep groove ball bearing with seals or shields |
| 159 kN | 118 kN | — | 2200 rpm | 5.79 kg5790 g |
| SKF6319-2RS1/C3Deep groove ball bearing with seals or shields |
| 159 kN | 118 kN | 7000 rpm | 2200 rpm | 5.79 kg5790 g |
| SKF6319-2ZDeep groove ball bearing with seals or shields |
| 159 kN | 118 kN | 7000 rpm | 3600 rpm | 5.84 kg5840 g |
| SKF6319-2Z/C3Deep groove ball bearing with seals or shields |
| 159 kN | 118 kN | 7000 rpm | 3600 rpm | 5.84 kg5840 g |
| SKF6319 2ZJEMDeep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 3600 rpm | 5.84 kg5840 g |
| SKF6319/C3Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.65 kg5650 g |
| SKF6319/C3VL0241INSOCOAT® deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.74 kg5740 g |
| SKF6319/C4Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.65 kg5650 g |
| SKF6319/HC5C3Hybrid ceramic deep groove ball bearing |
| 153 kN | 118 kN | 8500 rpm | 5300 rpm | 4.9 kg4900 g |
| SKF6319/HC5C3S0Hybrid ceramic deep groove ball bearing |
| 153 kN | 118 kN | 8500 rpm | 5300 rpm | 4.94 kg4940 g |
| SKF6319/HC5C3VA505SKF CeraDrive, hybrid ceramic deep groove ball bearing optimized for industrial electric motor |
| 159 kN | 104 kN | 8500 rpm | 5300 rpm | 5.67 kg5670 g |
| SKF6319 JEMDeep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.65 kg5650 g |
| SKF6319 MDeep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 6300 rpm | 7.17 kg7170 g |
| SKF6319 M/C3Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 6300 rpm | 6.94 kg6940 g |
| SKF6319 M/C3VL0241INSOCOAT® deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 6300 rpm | 6.52 kg6520 g |
| SKF6319 M/C4Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 6300 rpm | 6.94 kg6940 g |
| SKF6319 M/P64Deep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 6300 rpm | 6.94 kg6940 g |
| SKF6319-ZDeep groove ball bearing with seals or shields |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.69 kg5690 g |
| SKF6319-Z/C3Deep groove ball bearing with seals or shields |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.69 kg5690 g |
| SKF6319 ZJEMDeep groove ball bearing |
| 159 kN | 118 kN | 7000 rpm | 4500 rpm | 5.69 kg5690 g |
| FAG6319-2RSRDeep groove ball bearing |
| 154 kN | 113 kN | — | 2080 rpm | 6.193 kg6193 g |
| FAG6319-2RSR-C3Deep groove ball bearing |
| 154 kN | 113 kN | — | 2080 rpm | 6.193 kg6193 g |
| FAG6319-2ZDeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 3900 rpm | 6.2 kg6200 g |
| FAG6319-2Z-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 3900 rpm | 7.14 kg7140 g |
| FAG6319-2Z-L069-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 3900 rpm | 6.2 kg6200 g |
| FAG6319-2Z-L069-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 3900 rpm | 6.12 kg6120 g |
| FAG6319-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6.039 kg6039 g |
| FAG6319-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6.23 kg6230 g |
| FAG6319-J20AADeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 5.842 kg5842 g |
| FAG6319-J20AA-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 5.842 kg5842 g |
| FAG6319-J20ABDeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6 kg6000 g |
| FAG6319-J20AB-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 5.82 kg5820 g |
| FAG6319-J20GA-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6 kg6000 g |
| FAG6319-J20GA-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 6 kg6000 g |
| FAG6319-MDeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.889 kg6889 g |
| FAG6319-M-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.9 kg6900 g |
| FAG6319-M-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.9 kg6900 g |
| FAG6319-M-J20AA-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.695 kg6695 g |
| FAG6319-M-J20AA-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.695 kg6695 g |
| FAG6319-M-J20ABDeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.9 kg6900 g |
| FAG6319-M-J20AB-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.695 kg6695 g |
| FAG6319-M-J20GA-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.9 kg6900 g |
| FAG6319-M-J20GA-C4Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 6000 rpm | 6.9 kg6900 g |
| FAG6319-ZDeep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 5.926 kg5926 g |
| FAG6319-Z-C3Deep groove ball bearing |
| 154 kN | 113 kN | 4950 rpm | 4600 rpm | 5.926 kg5926 g |
| TIMKEN6319-2RSDeep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| TIMKEN6319-2RS-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| TIMKEN6319-2RZ-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.75 kg5750 g |
| TIMKEN6319-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| TIMKEN6319M-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 7.11 kg7110 g |
| TIMKEN6319-RSDeep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.75 kg5750 g |
| TIMKEN6319-ZDeep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.75 kg5750 g |
| TIMKEN6319-Z-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.75 kg5750 g |
| TIMKEN6319-ZZDeep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| TIMKEN6319-ZZ-C3Deep groove ball bearing |
| 153 kN | 118 kN | — | — | 5.67 kg5670 g |
| NSK6319DDUDeep groove ball bearing |
| 168 kN | 119 kN | — | — | — |
| NSK6319VVDeep groove ball bearing |
| 168 kN | 119 kN | — | — | — |
| NSK6319ZZDeep groove ball bearing |
| 168 kN | 119 kN | — | — | — |
| KOYO6319 2RSDeep groove ball bearing |
| 191 kN | 119 kN | — | 2200 rpmLimiting Speeds(Grease Lub.): 2200 min-1 | 5.67 kg5670 g |
| KOYO6319 2RUDeep groove ball bearing |
| 191 kN | 119 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1 | 5.67 kg5670 g |
| KOYO6319NRDeep groove ball bearing |
| 191 kN | 119 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1Limiting Speeds(Oil Lub.): 4000 min-1 | 5.67 kg5670 g |
| KOYO6319 ZZXDeep groove ball bearing |
| 191 kN | 119 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1 | 5.67 kg5670 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6319 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6319 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6319 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6319 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6319 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6319-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6319-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6319-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6319-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6319 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6319/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6319/C3VL0241 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6319/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6319/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6319/HC5C3S0 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6319/HC5C3VA505 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6319 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6319 M | Without | P6 and tighter width tolerance | CN | Machined brass | Bearing steel | None |
| SKF 6319 M/C3 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6319 M/C3VL0241 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6319 M/C4 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6319 M/P64 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6319-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6319-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6319 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6319-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6319-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6319-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6319-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6319-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6319-2Z-L069-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6319-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20AA | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-J20GA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20AA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-M-J20GA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6319-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6319-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6319-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319M-C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 6319-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6319-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6319DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6319VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6319ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6319 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6319 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6319NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6319 ZZX | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6319
Deep groove ball bearing
View full technical record →FAG6319
Deep groove ball bearing
View full technical record →TIMKEN6319
Deep groove ball bearing
View full technical record →KOYO6319
Deep groove ball bearing
View full technical record →NSK6319
Deep groove ball bearing
View full technical record →TIMKEN6319-2RS
Deep groove ball bearing
View full technical record →KOYO6319 2RS
Deep groove ball bearing
View full technical record →SKF6319-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6319-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6319-2RS-C3
Deep groove ball bearing
View full technical record →FAG6319-2RSR
Deep groove ball bearing
View full technical record →FAG6319-2RSR-C3
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.