Find · understand · compare
6316 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6316. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6316 dimensions and recorded technical data
The recorded 6316 base designation measures 80×170×39 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 81 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6316
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6316/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 80.0 mm |
| Outside diameter | Not supplied separately | 170.0 mm |
| Width | Not supplied separately | 39.0 mm |
SKF 6316 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 170 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.018 to 0 mm |
| Width | B | 39 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 108 mm |
| Recess diameter | D 2 | ≈ 146.9 mm |
| Chamfer dimension | r 1,2 | min. 2.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 92 mm |
| Diameter of housing abutment | D a | max. 158 mm |
| Radius of shaft or housing fillet | r a | max. 2 mm |
FAG 6316 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 170 mm |
| Width | B | 39 mm |
| Minimum chamfer dimension | rmin | 2.1 mm |
| Shoulder diameter outer ring | D1 | 141.92 mm |
| Shoulder diameter inner ring | d1 | 108.56 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 92 mm |
| Maximum diameter of housing shoulder | Da max | 158 mm |
| Maximum fillet radius | ra max | 2.1 mm |
FAG 6316-C3 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 170 mm |
| Width | B | 39 mm |
| Minimum chamfer dimension | rmin | 2.1 mm |
| Shoulder diameter outer ring | D1 | 141.92 mm |
| Shoulder diameter inner ring | d1 | 108.56 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 92 mm |
| Maximum diameter of housing shoulder | Da max | 158 mm |
| Maximum fillet radius | ra max | 2.1 mm |
KOYO 6316 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 170 mm |
| Width | B | 39 mm |
KOYO 6316 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 170 mm |
| Width | B | 39 mm |
TIMKEN 6316-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 170 mm / 6.693 in |
| Width (B) | B | 39 mm / 1.535 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
TIMKEN 6316-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 170 mm / 6.693 in |
| Width (B) | B | 39 mm / 1.535 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
TIMKEN 6316 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 170 mm / 6.693 in |
| Width (B) | B | 39 mm / 1.535 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6316Deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.54 kg3540 g |
| FAG6316Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.75 kg3750 g |
| TIMKEN6316Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| NSK6316Deep groove ball bearing |
| 135 kN | 86.5 kN | — | — | 3.67 kg3670 g |
| KOYO6316Deep groove ball bearing |
| 154 kN | 86.7 kN | — | 3900 rpmLimiting Speeds(Grease Lub.): 3900 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 3.59 kg3590 g |
| SKF6316-2RS1Deep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | — | 2600 rpm | 3.64 kg3640 g |
| SKF6316-2RS1/C3Deep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 2600 rpm | 3.64 kg3640 g |
| SKF6316 2RSJEMDeep groove ball bearing |
| 130 kN | 86.5 kN | — | 2600 rpm | 3.64 kg3640 g |
| SKF6316-2ZDeep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 4300 rpm | 3.68 kg3680 g |
| SKF6316-2Z/C3Deep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 4300 rpm | 3.68 kg3680 g |
| SKF6316-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 4300 rpm | 3.68 kg3680 g |
| SKF6316 2ZJEMDeep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 4300 rpm | 3.68 kg3680 g |
| SKF6316-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 86.5 kN | — | 30 rpm | 3.68 kg3680 g |
| SKF6316/C3Deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.54 kg3540 g |
| SKF6316/C3S1Deep groove ball bearing |
| 130 kN | 83 kN | 8500 rpm | 5300 rpm | 3.56 kg3560 g |
| SKF6316/C3VL0241INSOCOAT® deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.63 kg3630 g |
| SKF6316/C4Deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.6 kg3600 g |
| SKF6316/HC5C3S0Hybrid ceramic deep groove ball bearing |
| 124 kN | 86.5 kN | 10000 rpm | 6300 rpm | 3.09 kg3090 g |
| SKF6316/HC5C3VA505SKF CeraDrive, hybrid ceramic deep groove ball bearing optimized for industrial electric motor |
| 114 kN | 73.5 kN | 10000 rpm | 6300 rpm | 3.72 kg3720 g |
| SKF6316 JEMDeep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.6 kg3600 g |
| SKF6316 MDeep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 7500 rpm | 4.5 kg4500 g |
| SKF6316 M/C3Deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 7500 rpm | 4.12 kg4120 g |
| SKF6316 M/C3VL0241INSOCOAT® deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 7500 rpm | 4.13 kg4130 g |
| SKF6316 M/C4Deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 7500 rpm | 4.36 kg4360 g |
| SKF6316 M/C4VL0241INSOCOAT® deep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 7500 rpm | 4.13 kg4130 g |
| SKF6316-RS1Deep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | — | 2600 rpm | 3.56 kg3560 g |
| SKF6316-ZDeep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.59 kg3590 g |
| SKF6316-Z/C3Deep groove ball bearing with seals or shields |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.59 kg3590 g |
| SKF6316 ZJEMDeep groove ball bearing |
| 130 kN | 86.5 kN | 8500 rpm | 5300 rpm | 3.59 kg3590 g |
| FAG6316-2RSRDeep groove ball bearing |
| 131 kN | 87 kN | — | 2470 rpm | 3.79 kg3790 g |
| FAG6316-2RSR-C3Deep groove ball bearing |
| 131 kN | 87 kN | — | 2470 rpm | 3.79 kg3790 g |
| FAG6316-2ZDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.75 kg3750 g |
| FAG6316-2Z-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.75 kg3750 g |
| FAG6316-2Z-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.75 kg3750 g |
| FAG6316-2Z-L038-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.78 kg3780 g |
| FAG6316-2Z-L069-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.78 kg3780 g |
| FAG6316-2Z-L069-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.78 kg3780 g |
| FAG6316-2Z-L138Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.82 kg3820 g |
| FAG6316-2Z-L207-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 4550 rpm | 3.78 kg3780 g |
| FAG6316-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.82 kg3820 g |
| FAG6316-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.75 kg3750 g |
| FAG6316-J20AA-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.651 kg3651 g |
| FAG6316-J20ABDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.68 kg3680 g |
| FAG6316-J20AB-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.68 kg3680 g |
| FAG6316-J20CDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.75 kg3750 g |
| FAG6316-J20C-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.75 kg3750 g |
| FAG6316-J20GA-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.68 kg3680 g |
| FAG6316-MDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.31 kg4310 g |
| FAG6316-M-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.31 kg4310 g |
| FAG6316-M-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.31 kg4310 g |
| FAG6316-M-J20AA-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.319 kg4319 g |
| FAG6316-M-J20AA-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.319 kg4319 g |
| FAG6316-M-J20GA-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 4.37 kg4370 g |
| FAG6316-M-J20GA-C4Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 7000 rpm | 3.68 kg3680 g |
| FAG6316-RSR-C3Deep groove ball bearing |
| 131 kN | 87 kN | — | 2470 rpm | 3.77 kg3770 g |
| FAG6316-TVHDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.59 kg3590 g |
| FAG6316-ZDeep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.8 kg3800 g |
| FAG6316-Z-C3Deep groove ball bearing |
| 131 kN | 87 kN | 5500 rpm | 5400 rpm | 3.72 kg3720 g |
| TIMKEN6316-2RSDeep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-2RS-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-2RS/VSL609Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-2RZDeep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.6 kg3600 g |
| TIMKEN6316-2RZ-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.6 kg3600 g |
| TIMKEN6316-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316M-2RS-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 4.48 kg4480 g |
| TIMKEN6316M-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 4.48 kg4480 g |
| TIMKEN6316-RS-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.6 kg3600 g |
| TIMKEN6316-RS-C4Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.6 kg3600 g |
| TIMKEN6316/VSL609Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-ZDeep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-Z-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-ZZDeep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-ZZ-C3Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.59 kg3590 g |
| TIMKEN6316-ZZ-C4Deep groove ball bearing |
| 123 kN | 86.5 kN | — | — | 3.6 kg3600 g |
| NSK6316DDUDeep groove ball bearing |
| 135 kN | 86.5 kN | — | — | — |
| NSK6316VVDeep groove ball bearing |
| 135 kN | 86.5 kN | — | — | — |
| NSK6316ZZDeep groove ball bearing |
| 135 kN | 86.5 kN | — | — | — |
| KOYO6316 2RSDeep groove ball bearing |
| 154 kN | 86.7 kN | — | 2700 rpmLimiting Speeds(Grease Lub.): 2700 min-1 | 3.59 kg3590 g |
| KOYO6316 2RUDeep groove ball bearing |
| 154 kN | 86.7 kN | — | 3900 rpmLimiting Speeds(Grease Lub.): 3900 min-1 | 3.59 kg3590 g |
| KOYO6316NRDeep groove ball bearing |
| 154 kN | 86.7 kN | — | 3900 rpmLimiting Speeds(Grease Lub.): 3900 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 3.59 kg3590 g |
| KOYO6316 ZZDeep groove ball bearing |
| 154 kN | 86.7 kN | — | 3900 rpmLimiting Speeds(Grease Lub.): 3900 min-1 | 3.59 kg3590 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6316 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6316 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6316 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6316 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6316 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6316-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6316-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6316 2RSJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6316-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6316-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6316-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6316 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6316-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6316/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6316/C3S1 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6316/C3VL0241 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6316/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6316/HC5C3S0 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6316/HC5C3VA505 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6316 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6316 M | Without | P6 and tighter width tolerance | CN | Machined brass | Bearing steel | None |
| SKF 6316 M/C3 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6316 M/C3VL0241 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6316 M/C4 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6316 M/C4VL0241 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6316-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6316-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6316-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6316 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6316-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6316-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6316-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6316-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6316-2Z-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6316-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6316-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6316-2Z-L069-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6316-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6316-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6316-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20C | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20C-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-J20AA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-M-J20GA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6316-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-TVH | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | Without — Bearing not greased |
| FAG 6316-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6316-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6316-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316M-2RS-C3 | Sealed | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 6316M-C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 6316-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-RS-C4 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6316-ZZ-C4 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6316DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6316VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6316ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6316 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6316 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6316NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6316 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6316
Deep groove ball bearing
View full technical record →FAG6316
Deep groove ball bearing
View full technical record →TIMKEN6316
Deep groove ball bearing
View full technical record →KOYO6316
Deep groove ball bearing
View full technical record →NSK6316
Deep groove ball bearing
View full technical record →TIMKEN6316-2RS
Deep groove ball bearing
View full technical record →KOYO6316 2RS
Deep groove ball bearing
View full technical record →SKF6316-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6316-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6316-2RS-C3
Deep groove ball bearing
View full technical record →SKF6316 2RSJEM
Deep groove ball bearing
View full technical record →FAG6316-2RSR
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.