Find · understand · compare
6315 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6315. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6315 dimensions and recorded technical data
The recorded 6315 base designation measures 75×160×37 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 94 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6315
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6315/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 75.0 mm |
| Outside diameter | Not supplied separately | 160.0 mm |
| Width | Not supplied separately | 37.0 mm |
SKF 6315 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 160 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.018 to 0 mm |
| Width | B | 37 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 101.4 mm |
| Recess diameter | D 2 | ≈ 138.4 mm |
| Chamfer dimension | r 1,2 | min. 2.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 87 mm |
| Diameter of housing abutment | D a | max. 148 mm |
| Radius of shaft or housing fillet | r a | max. 2 mm |
FAG 6315 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 160 mm |
| Width | B | 37 mm |
| Minimum chamfer dimension | rmin | 2.1 mm |
| Shoulder diameter outer ring | D1 | 133.34 mm |
| Shoulder diameter inner ring | d1 | 101.77 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 87 mm |
| Maximum diameter of housing shoulder | Da max | 148 mm |
| Maximum fillet radius | ra max | 2.1 mm |
FAG 6315-C3 — 9 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 160 mm |
| Width | B | 37 mm |
| Minimum chamfer dimension | rmin | 2.1 mm |
| Shoulder diameter outer ring | D1 | 133.34 mm |
| Shoulder diameter inner ring | d1 | 101.77 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 87 mm |
| Maximum diameter of housing shoulder | Da max | 148 mm |
| Maximum fillet radius | ra max | 2.1 mm |
KOYO 6315 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 160 mm |
| Width | B | 37 mm |
KOYO 6315 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 160 mm |
| Width | B | 37 mm |
TIMKEN 6315-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 160 mm / 6.299 in |
| Width (B) | B | 37 mm / 1.457 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
TIMKEN 6315-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 160 mm / 6.299 in |
| Width (B) | B | 37 mm / 1.457 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
TIMKEN 6315 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 160 mm / 6.299 in |
| Width (B) | B | 37 mm / 1.457 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 2.1 mm / 0.083 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6315Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 2.99 kg2990 g |
| FAG6315Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.076 kg3076 g |
| TIMKEN6315Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| NSK6315Deep groove ball bearing |
| 125 kN | 77 kN | — | — | 3.08 kg3080 g |
| KOYO6315Deep groove ball bearing |
| 142 kN | 77.2 kN | — | 4200 rpmLimiting Speeds(Grease Lub.): 4200 min-1Limiting Speeds(Oil Lub.): 5000 min-1 | 3.02 kg3020 g |
| SKF6315-2RS1Deep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | — | 2800 rpm | 3.08 kg3080 g |
| SKF6315-2RS1/C3Deep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 2800 rpm | 3.08 kg3080 g |
| SKF6315 2RSJEMDeep groove ball bearing |
| 119 kN | 76.5 kN | — | 2800 rpm | 3.07 kg3070 g |
| SKF6315-2ZDeep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 4500 rpm | 3.1 kg3100 g |
| SKF6315-2Z/C3Deep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 4500 rpm | 3.09 kg3090 g |
| SKF6315-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 4500 rpm | 3.1 kg3100 g |
| SKF6315-2Z/C3WTDeep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 4500 rpm | 3.1 kg3100 g |
| SKF6315 2ZJEMDeep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 4500 rpm | 3.12 kg3120 g |
| SKF6315-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 76.5 kN | — | 30 rpm | 3.19 kg3190 g |
| SKF6315/AXDDeep groove ball bearing |
| 143 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.06 kg3060 g |
| SKF6315/C3Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 2.99 kg2990 g |
| SKF6315/C3VL0241INSOCOAT® deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.04 kg3040 g |
| SKF6315/C4Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 2.99 kg2990 g |
| SKF6315/HC5C3Hybrid ceramic deep groove ball bearing |
| 114 kN | 76.5 kN | 11000 rpm | 6700 rpm | 2.63 kg2630 g |
| SKF6315/HC5C3S0Hybrid ceramic deep groove ball bearing |
| 114 kN | 76.5 kN | 11000 rpm | 6700 rpm | 2.63 kg2630 g |
| SKF6315/HC5C3VA505SKF CeraDrive, hybrid ceramic deep groove ball bearing optimized for industrial electric motor |
| 99.5 kN | 64 kN | 11000 rpm | 6700 rpm | 3.15 kg3150 g |
| SKF6315 JEMDeep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.04 kg3040 g |
| SKF6315 M/C3Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 8000 rpm | 3.45 kg3450 g |
| SKF6315 M/C3S0VQ335Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 8000 rpm | 3.64 kg3640 g |
| SKF6315 M/C3VL0241INSOCOAT® deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 8000 rpm | 3.56 kg3560 g |
| SKF6315 M/C4Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 8000 rpm | 3.69 kg3690 g |
| SKF6315 M/C4HVL0241INSOCOAT® deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 8000 rpm | 3.56 kg3560 g |
| SKF6315 M/HC5C3HS0Hybrid ceramic deep groove ball bearing |
| 114 kN | 76.5 kN | 11000 rpm | 8000 rpm | 3.09 kg3090 g |
| SKF6315 M/HC5C3S0Hybrid ceramic deep groove ball bearing |
| 114 kN | 76.5 kN | 11000 rpm | 8000 rpm | 3.09 kg3090 g |
| SKF6315/VA201Deep groove ball bearing for high temperature applications |
| — | 76.5 kN | — | 40 rpm | 3 kg3000 g |
| SKF6315-ZDeep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.03 kg3030 g |
| SKF6315-Z/C3Deep groove ball bearing with seals or shields |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.03 kg3030 g |
| SKF6315-Z/C3VL0241Deep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.03 kg3030 g |
| SKF6315 ZJEMDeep groove ball bearing |
| 119 kN | 76.5 kN | 9000 rpm | 5600 rpm | 3.03 kg3030 g |
| FAG6315-2RSRDeep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-C3Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-C4Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-L038-C3Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-L138-C3Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-L140Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2RSR-L140-C3Deep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-2ZDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.2 kg3200 g |
| FAG6315-2Z-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.2 kg3200 g |
| FAG6315-2Z-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.2 kg3200 g |
| FAG6315-2Z-L069-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.23 kg3230 g |
| FAG6315-2Z-L069-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.23 kg3230 g |
| FAG6315-2Z-L138Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.131 kg3131 g |
| FAG6315-2Z-L408-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 5400 rpm | 3.173 kg3173 g |
| FAG6315-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.076 kg3076 g |
| FAG6315-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.18 kg3180 g |
| FAG6315-H-2RSR-SN-C3>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | — | 2650 rpm | 3.09 kg3090 g |
| FAG6315-H-2RSR-SN>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | — | 2650 rpm | 3.09 kg3090 g |
| FAG6315-H-2Z-SN-C3>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | 5800 rpm | 4850 rpm | 3.07 kg3070 g |
| FAG6315-H-2Z-SN>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | 5800 rpm | 4850 rpm | 3.07 kg3070 g |
| FAG6315-H-SN-C3>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | 5800 rpm | 5700 rpm | 3.15 kg3150 g |
| FAG6315-H-SN>NDeep groove ball bearing |
| 113.42 kN | 76.97 kN | 5800 rpm | 5700 rpm | 3.15 kg3150 g |
| FAG6315-J20AA-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.07 kg3070 g |
| FAG6315-J20ABDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.06 kg3060 g |
| FAG6315-J20AB-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.06 kg3060 g |
| FAG6315-J20GA-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.06 kg3060 g |
| FAG6315-MDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.75 kg3750 g |
| FAG6315-M-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.75 kg3750 g |
| FAG6315-M-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.7 kg3700 g |
| FAG6315-M-J20AADeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.744 kg3744 g |
| FAG6315-M-J20AA-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.744 kg3744 g |
| FAG6315-M-J20AA-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.744 kg3744 g |
| FAG6315-M-J20ABDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.744 kg3744 g |
| FAG6315-M-J20AB-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.744 kg3744 g |
| FAG6315-M-J20GA-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 8200 rpm | 3.67 kg3670 g |
| FAG6315-NDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.18 kg3180 g |
| FAG6315-RSRDeep groove ball bearing |
| 123 kN | 77 kN | — | 2650 rpm | 3.18 kg3180 g |
| FAG6315-ZDeep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.13 kg3130 g |
| FAG6315-Z-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.13 kg3130 g |
| FAG6315-Z-C4Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.13 kg3130 g |
| FAG6315-Z-L038-C3Deep groove ball bearing |
| 123 kN | 77 kN | 5800 rpm | 6300 rpm | 3.199 kg3199 g |
| TIMKEN6315-2RSDeep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-2RS-C3Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-2RS/VSL609Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-C3Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-RSDeep groove ball bearing |
| 113 kN | 77 kN | — | — | 3 kg3000 g |
| TIMKEN6315-RS-C3Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315/VSL609Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-ZDeep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-Z-C3Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-Z-NRDeep groove ball bearing |
| 113 kN | 77 kN | — | — | 3 kg3000 g |
| TIMKEN6315-ZZDeep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| TIMKEN6315-ZZ-C3Deep groove ball bearing |
| 113 kN | 77 kN | — | — | 3.02 kg3020 g |
| NSK6315DDUDeep groove ball bearing |
| 125 kN | 77 kN | — | — | — |
| NSK6315VVDeep groove ball bearing |
| 125 kN | 77 kN | — | — | — |
| NSK6315ZZDeep groove ball bearing |
| 125 kN | 77 kN | — | — | — |
| KOYO6315 2RSDeep groove ball bearing |
| 142 kN | 77.2 kN | — | 2800 rpmLimiting Speeds(Grease Lub.): 2800 min-1 | 3.02 kg3020 g |
| KOYO6315 2RUDeep groove ball bearing |
| 142 kN | 77.2 kN | — | 4200 rpmLimiting Speeds(Grease Lub.): 4200 min-1 | 3.02 kg3020 g |
| KOYO6315NRDeep groove ball bearing |
| 142 kN | 77.2 kN | — | 4200 rpmLimiting Speeds(Grease Lub.): 4200 min-1Limiting Speeds(Oil Lub.): 5000 min-1 | 3.02 kg3020 g |
| KOYO6315 ZZDeep groove ball bearing |
| 142 kN | 77.2 kN | — | 4200 rpmLimiting Speeds(Grease Lub.): 4200 min-1 | 3.02 kg3020 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6315 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6315 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6315 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6315 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6315 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6315-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6315-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315 2RSJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6315-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315-2Z/C3WT | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6315-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6315/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6315/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6315/C3VL0241 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6315/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6315/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6315/HC5C3S0 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6315/HC5C3VA505 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6315 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6315 M/C3 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6315 M/C3S0VQ335 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6315 M/C3VL0241 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6315 M/C4 | Without | Not recorded | C4 | Machined brass | Bearing steel | None |
| SKF 6315 M/C4HVL0241 | Without | Not recorded | C4H | Machined brass | Bearing steel | None |
| SKF 6315 M/HC5C3HS0 | Without | Not recorded | C3H | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6315 M/HC5C3S0 | Without | Not recorded | C3 | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6315/VA201 | Without | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6315-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6315-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6315-Z/C3VL0241 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6315 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6315-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2RSR-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6315-2RSR-L138-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6315-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6315-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6315-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2Z-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6315-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6315-2Z-L069-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6315-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6315-2Z-L408-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L408 — Grease (L408/customer specific) |
| FAG 6315-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-H-2RSR-SN-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6315-H-2RSR-SN>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6315-H-2Z-SN-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6315-H-2Z-SN>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6315-H-SN-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-H-SN>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20AA | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20AA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20AA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20AB | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20AB-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-M-J20GA-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6315-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-Z-C4 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6315-Z-L038-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| TIMKEN 6315-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6315-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6315DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6315VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6315ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6315 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6315 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6315NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6315 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6315
Deep groove ball bearing
View full technical record →FAG6315
Deep groove ball bearing
View full technical record →TIMKEN6315
Deep groove ball bearing
View full technical record →KOYO6315
Deep groove ball bearing
View full technical record →NSK6315
Deep groove ball bearing
View full technical record →TIMKEN6315-2RS
Deep groove ball bearing
View full technical record →KOYO6315 2RS
Deep groove ball bearing
View full technical record →SKF6315-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6315-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6315-2RS-C3
Deep groove ball bearing
View full technical record →SKF6315 2RSJEM
Deep groove ball bearing
View full technical record →FAG6315-2RSR
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.