Find · understand · compare
6308 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6308. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6308 dimensions and recorded technical data
The recorded 6308 base designation measures 40×90×23 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO, NACHI. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 175 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6308
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6308-2Z/C3 — 3 dimension fields
Deep groove ball bearing with seals or shields. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 40.0 mm |
| Outside diameter | Not supplied separately | 90.0 mm |
| Width | Not supplied separately | 23.0 mm |
SKF 6308-Z — 13 dimension fields
Deep groove ball bearing with seals or shields. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 90 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 23 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 56.11 mm |
| Recess diameter | D 2 | ≈ 77.7 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 49 mm |
| Diameter of shaft abutment | d a | max. 56 mm |
| Diameter of housing abutment | D a | max. 81 mm |
| Radius of shaft or housing fillet | r a | max. 1.5 mm |
SKF 6308/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 40.0 mm |
| Outside diameter | Not supplied separately | 90.0 mm |
| Width | Not supplied separately | 23.0 mm |
SKF 6308 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 90 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 23 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 56.11 mm |
| Recess diameter | D 2 | ≈ 77.7 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 49 mm |
| Diameter of housing abutment | D a | max. 81 mm |
| Radius of shaft or housing fillet | r a | max. 1.5 mm |
FAG 6308-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 74.64 mm |
| Caliber diameter outer ring | D2 | 76.5 mm |
| Shoulder diameter inner ring | d1 | 55.55 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 49 mm |
| Maximum diameter of housing shoulder | Da max | 81 mm |
| Maximum fillet radius | ra max | 1.5 mm |
FAG 6308 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 74.64 mm |
| Caliber diameter outer ring | D2 | 76.5 mm |
| Shoulder diameter inner ring | d1 | 55.55 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 49 mm |
| Maximum diameter of housing shoulder | Da max | 81 mm |
| Maximum fillet radius | ra max | 1.5 mm |
FAG 6308-Z — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 74.64 mm |
| Caliber diameter outer ring | D2 | 76.5 mm |
| Shoulder diameter inner ring | d1 | 55.55 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 49 mm |
| Maximum diameter of housing shoulder | Da max | 81 mm |
| Maximum fillet radius | ra max | 1.5 mm |
FAG 6308-2Z-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
| Minimum chamfer dimension | rmin | 1.5 mm |
| Shoulder diameter outer ring | D1 | 74.64 mm |
| Caliber diameter outer ring | D2 | 76.5 mm |
| Shoulder diameter inner ring | d1 | 55.55 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 49 mm |
| Maximum diameter of housing shoulder | Da max | 81 mm |
| Maximum fillet radius | ra max | 1.5 mm |
KOYO 6308 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
KOYO 6308 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
KOYO 6308 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 90 mm |
| Width | B | 23 mm |
TIMKEN 6308-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308-Z — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308-ZZ-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
TIMKEN 6308 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 23 mm / 0.906 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.5 mm / 0.059 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6308Deep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.611 kg611 g |
| FAG6308Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.611 kg611 g |
| TIMKEN6308Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| NSK6308Deep groove ball bearing |
| 45 kN | 24 kN | — | — | 0.636 kg636 g |
| KOYO6308Deep groove ball bearing |
| 50.9 kN | 24 kN | — | 7700 rpmLimiting Speeds(Grease Lub.): 7700 min-1Limiting Speeds(Oil Lub.): 9200 min-1 | 0.633 kg633 g |
| NACHI6308Deep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | 0.633 kg633 g |
| SKF6308-2RS1Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/C3Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/C3LHT23Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.647 kg647 g |
| SKF6308-2RS1/C4Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/C4GJNDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/C4VT486Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1/GJNDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.635 kg635 g |
| SKF6308-2RS1/HC5C3GJNHybrid ceramic deep groove ball bearing with seals on both sides |
| 41 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308-2RS1NRDeep groove ball bearing with snap ring and integral sealing |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.646 kg646 g |
| SKF6308-2RS1NR/C3Deep groove ball bearing with snap ring and integral sealing |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.646 kg646 g |
| SKF6308 2RSJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.63 kg630 g |
| SKF6308 2RSNRJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.614 kg614 g |
| SKF6308-2RZDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.625 kg625 g |
| SKF6308-2RZTN9/HC5C3WTHybrid ceramic deep groove ball bearing with seals on both sides |
| 41 kN | 24 kN | 20000 rpm | 11000 rpm | 0.565 kg565 g |
| SKF6308-2ZDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C3Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C3HTDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C3WTDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C4Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/C4WTDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308-2Z/GJNDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308 2ZJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.635 kg635 g |
| SKF6308 2ZNRJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 8500 rpm | 0.651 kg651 g |
| SKF6308-2Z/VA201Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 24 kN | — | 70 rpm | 0.635 kg635 g |
| SKF6308-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 24 kN | — | 60 rpm | 0.626 kg626 g |
| SKF6308-2Z/VA228Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 24 kN | — | 130 rpm | 0.635 kg635 g |
| SKF6308/AXDDeep groove ball bearing |
| 50.7 kN | 24 kN | 17000 rpm | 11000 rpm | 0.625 kg625 g |
| SKF6308/C3Deep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.611 kg611 g |
| SKF6308/C3S1Deep groove ball bearing |
| 42.3 kN | 22.8 kN | 17000 rpm | 11000 rpm | 0.627 kg627 g |
| SKF6308/C4Deep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.611 kg611 g |
| SKF6308/HC5C3Hybrid ceramic deep groove ball bearing |
| 41 kN | 24 kN | 20000 rpm | 13000 rpm | 0.611 kg611 g |
| SKF6308 JEMDeep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.611 kg611 g |
| SKF6308 M/HC5C4S0Hybrid ceramic deep groove ball bearing |
| 41 kN | 24 kN | 20000 rpm | 15000 rpm | 0.684 kg684 g |
| SKF6308 NDeep groove ball bearing with snap ring groove |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.602 kg602 g |
| SKF6308 NRDeep groove ball bearing with snap ring |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.626 kg626 g |
| SKF6308 NR/C3Deep groove ball bearing with snap ring |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.626 kg626 g |
| SKF6308 NRJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.626 kg626 g |
| SKF6308-RS1Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.616 kg616 g |
| SKF6308 RSJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | — | 5000 rpm | 0.616 kg616 g |
| SKF6308/VA201Deep groove ball bearing for high temperature applications |
| — | 24 kN | — | 70 rpm | 0.607 kg607 g |
| SKF6308-ZDeep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.618 kg618 g |
| SKF6308-Z/C3Deep groove ball bearing with seals or shields |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.618 kg618 g |
| SKF6308 ZJEMDeep groove ball bearing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.618 kg618 g |
| SKF6308-ZNRDeep groove ball bearing with snap ring and integral sealing |
| 42.3 kN | 24 kN | 17000 rpm | 11000 rpm | 0.634 kg634 g |
| FAG6308-2RSRDeep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.632 kg632 g |
| FAG6308-2RSR-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.632 kg632 g |
| FAG6308-2RSR-L038Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.636 kg636 g |
| FAG6308-2RSR-L038-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.65 kg650 g |
| FAG6308-2RSR-L055-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.654 kg654 g |
| FAG6308-2RSR-L100-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.628 kg628 g |
| FAG6308-2RSR-L138-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.636 kg636 g |
| FAG6308-2RSR-L140Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.628 kg628 g |
| FAG6308-2RSR-L140-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.628 kg628 g |
| FAG6308-2RSR-L207Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.628 kg628 g |
| FAG6308-2RSR-L207-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.628 kg628 g |
| FAG6308-2RSR-N-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.627 kg627 g |
| FAG6308-2RSR-TVH-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.66 kg660 g |
| FAG6308-2ZDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.631 kg631 g |
| FAG6308-2Z-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.631 kg631 g |
| FAG6308-2Z-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.631 kg631 g |
| FAG6308-2Z-CMDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.644 kg644 g |
| FAG6308-2Z-L038Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.638 kg638 g |
| FAG6308-2Z-L038-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.638 kg638 g |
| FAG6308-2Z-L038-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.638 kg638 g |
| FAG6308-2Z-L069-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.642 kg642 g |
| FAG6308-2Z-L100-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.635 kg635 g |
| FAG6308-2Z-L138Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.636 kg636 g |
| FAG6308-2Z-L138-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.636 kg636 g |
| FAG6308-2Z-L140-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.635 kg635 g |
| FAG6308-2Z-L207Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.635 kg635 g |
| FAG6308-2Z-L207-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.635 kg635 g |
| FAG6308-2Z-L207-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.632 kg632 g |
| FAG6308-2Z-L408-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 9100 rpm | 0.643 kg643 g |
| FAG6308-C-2BRS>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.621 kg621 g |
| FAG6308-C-2HRS-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.626 kg626 g |
| FAG6308-C-2HRS-C4>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.623 kg623 g |
| FAG6308-C-2HRS-L055-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.626 kg626 g |
| FAG6308-C-2HRS-L069-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.626 kg626 g |
| FAG6308-C-2HRS-L100-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.626 kg626 g |
| FAG6308-C-2HRS-L207>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.626 kg626 g |
| FAG6308-C-2HRS>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.621 kg621 g |
| FAG6308-C-2Z-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.618 kg618 g |
| FAG6308-C-2Z-C4>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.621 kg621 g |
| FAG6308-C-2Z-L069-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.62 kg620 g |
| FAG6308-C-2Z-L100-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.621 kg621 g |
| FAG6308-C-2Z-L138-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.621 kg621 g |
| FAG6308-C-2Z-L207-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.619 kg619 g |
| FAG6308-C-2Z-L207-C4>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.619 kg619 g |
| FAG6308-C-2Z>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 10100 rpm | 0.621 kg621 g |
| FAG6308-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.611 kg611 g |
| FAG6308-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.611 kg611 g |
| FAG6308-C-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.604 kg604 g |
| FAG6308-C-C4>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.604 kg604 g |
| FAG6308-C-HRS-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.601 kg601 g |
| FAG6308-C-HRS>VDeep groove ball bearing |
| 50 kN | 25 kN | — | 7400 rpm | 0.603 kg603 g |
| FAG6308-C-N-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.596 kg596 g |
| FAG6308-C-NR>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.622 kg622 g |
| FAG6308-C-N>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.596 kg596 g |
| FAG6308-C-TVH3-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.578 kg578 g |
| FAG6308-C>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.604 kg604 g |
| FAG6308-C-Z-C3>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.603 kg603 g |
| FAG6308-C-Z>VDeep groove ball bearing |
| 50 kN | 25 kN | 9900 rpm | 11800 rpm | 0.612 kg612 g |
| FAG6308-H-2RSR-C3>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | — | 4850 rpm | 0.654 kg654 g |
| FAG6308-H-2RSR-L038-C3>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | — | 4850 rpm | 0.63 kg630 g |
| FAG6308-H-2RSR-L138-C3>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | — | 4850 rpm | 0.675 kg675 g |
| FAG6308-H-2RSR>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | — | 4850 rpm | 0.654 kg654 g |
| FAG6308-H-2Z-C3>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | 8900 rpm | 9200 rpm | 0.654 kg654 g |
| FAG6308-H-2Z>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | 8900 rpm | 9200 rpm | 0.654 kg654 g |
| FAG6308-H-C3>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | 8900 rpm | 10800 rpm | 0.64 kg640 g |
| FAG6308-H>NDeep groove ball bearing |
| 40.76 kN | 24.01 kN | 8900 rpm | 10800 rpm | 0.64 kg640 g |
| FAG6308-MDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 14000 rpm | 0.8 kg800 g |
| FAG6308-M-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 14000 rpm | 0.76 kg760 g |
| FAG6308-M-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 14000 rpm | 0.76 kg760 g |
| FAG6308-M-S1-J20GA-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 14000 rpm | 0.72 kg720 g |
| FAG6308-NDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.605 kg605 g |
| FAG6308-N-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.622 kg622 g |
| FAG6308-NRDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.622 kg622 g |
| FAG6308-NR-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.622 kg622 g |
| FAG6308-RSRDeep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.618 kg618 g |
| FAG6308-RSR-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | — | 4800 rpm | 0.618 kg618 g |
| FAG6308-TVH-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.59 kg590 g |
| FAG6308-ZDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.618 kg618 g |
| FAG6308-Z-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.618 kg618 g |
| FAG6308-Z-C4Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.62 kg620 g |
| FAG6308-Z-NDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.65 kg650 g |
| FAG6308-Z-N-C3Deep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.65 kg650 g |
| FAG6308-Z-NRDeep groove ball bearing |
| 45.5 kN | 25 kN | 9000 rpm | 10800 rpm | 0.638 kg638 g |
| TIMKEN6308-2RSDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-2RS-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-2RS-C3/VSL609Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-2RS-NRDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-2RS-NR-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-2RS/VSL609Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-2RZDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-2RZ-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-2RZ-NR-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-C4Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-NRDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-NR-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-RSDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-RS-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308/VSL609Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-ZDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-Z-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-Z-NRDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-Z-NR-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.64 kg640 g |
| TIMKEN6308-ZZDeep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| TIMKEN6308-ZZ-C3Deep groove ball bearing |
| 40.8 kN | 24 kN | — | — | 0.63 kg630 g |
| NSK6308DDUDeep groove ball bearing |
| 45 kN | 24 kN | — | — | — |
| NSK6308VVDeep groove ball bearing |
| 45 kN | 24 kN | — | — | — |
| NSK6308ZZDeep groove ball bearing |
| 45 kN | 24 kN | — | — | — |
| KOYO6308 2RDDeep groove ball bearing |
| 50.9 kN | 24 kN | — | 6900 rpmLimiting Speeds(Grease Lub.): 6900 min-1 | 0.633 kg633 g |
| KOYO6308 2RSDeep groove ball bearing |
| 50.9 kN | 24 kN | — | 5100 rpmLimiting Speeds(Grease Lub.): 5100 min-1 | 0.633 kg633 g |
| KOYO6308 2RUDeep groove ball bearing |
| 50.9 kN | 24 kN | — | 7700 rpmLimiting Speeds(Grease Lub.): 7700 min-1 | 0.633 kg633 g |
| KOYO6308NRDeep groove ball bearing |
| 50.9 kN | 24 kN | — | 7700 rpmLimiting Speeds(Grease Lub.): 7700 min-1Limiting Speeds(Oil Lub.): 9200 min-1 | 0.633 kg633 g |
| KOYO6308TPT4C5Automotive bearing |
| — | — | — | — | 0.634 kg634 g |
| KOYO6308W-12RSHR4C5Automotive bearing |
| — | — | — | — | 0.67 kg670 g |
| KOYO6308W2RSHR4C5Automotive bearing |
| — | — | — | — | 0.627 kg627 g |
| KOYO6308W2RSHR4SH2C5Automotive bearing |
| — | — | — | — | 0.63 kg630 g |
| KOYO6308 ZZDeep groove ball bearing |
| 50.9 kN | 24 kN | — | 7700 rpmLimiting Speeds(Grease Lub.): 7700 min-1 | 0.633 kg633 g |
| NACHI6308-2NKE9Deep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
| NACHI6308-2NSE9Deep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
| NACHI6308NKE9Deep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
| NACHI6308NSE9Deep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
| NACHI6308ZEDeep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
| NACHI6308ZZEDeep groove ball bearing |
| 51.5 kN | 24.1 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6308 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6308 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6308 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6308 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6308-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C3LHT23 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C4 | Seal on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C4GJN | Seal on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/C4VT486 | Seal on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/GJN | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1/HC5C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | Grease |
| SKF 6308-2RS1NR | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RS1NR/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6308 2RSNRJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6308-2RZ | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308-2RZTN9/HC5C3WT | Seal on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6308-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C3HT | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C3WT | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C4 | Shield on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/C4WT | Shield on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/GJN | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6308 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6308 2ZNRJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6308-2Z/VA201 | Shield on both sides | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6308-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6308-2Z/VA228 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6308/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6308/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6308/C3S1 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6308/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6308/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6308 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6308 M/HC5C4S0 | Without | Not recorded | C4 | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6308 N | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6308 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6308 NR/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6308 NRJEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6308-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6308 RSJEM | Seal on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6308/VA201 | Without | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6308-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6308-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6308 ZJEM | Shield on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6308-ZNR | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6308-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-2RSR-L055-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L055 — Grease (L055/customer specific) |
| FAG 6308-2RSR-L100-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6308-2RSR-L138-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6308-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6308-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6308-2RSR-L207 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-2RSR-L207-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-2RSR-N-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2RSR-TVH-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2Z-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2Z-CM | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CM (Group M) — Internal clearance limited for electric motors | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-2Z-L038-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6308-2Z-L100-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6308-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6308-2Z-L138-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6308-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6308-2Z-L207 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-2Z-L207-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-2Z-L408-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L408 — Grease (L408/customer specific) |
| FAG 6308-C-2BRS>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2HRS-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2HRS-C4>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2HRS-L055-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L055 — Grease (L055/customer specific) |
| FAG 6308-C-2HRS-L069-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6308-C-2HRS-L100-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6308-C-2HRS-L207>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-C-2HRS>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2Z-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2Z-C4>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C-2Z-L069-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6308-C-2Z-L100-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6308-C-2Z-L138-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6308-C-2Z-L207-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-C-2Z-L207-C4>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6308-C-2Z>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6308-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-C4>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-HRS-C3>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-HRS>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-N-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-NR>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-N>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-TVH3-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | TVH3 — Solid cage made of glass-fiber\nreinforced polyamid PA46 | Not recorded | Without — Bearing not greased |
| FAG 6308-C>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-Z-C3>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-C-Z>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6308-H-2RSR-L038-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6308-H-2RSR-L138-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6308-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6308-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6308-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6308-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6308-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6308-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6308-M-S1-J20GA-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6308-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-N-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-NR-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-TVH-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | Without — Bearing not greased |
| FAG 6308-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-Z-C4 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-Z-N | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-Z-N-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6308-Z-NR | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6308-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RS-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RS-NR-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-2RZ-NR-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-Z-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6308-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6308DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6308VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6308ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308TPT4C5 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308W-12RSHR4C5 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308W2RSHR4C5 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308W2RSHR4SH2C5 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6308 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6308ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6308
Deep groove ball bearing
View full technical record →FAG6308
Deep groove ball bearing
View full technical record →TIMKEN6308
Deep groove ball bearing
View full technical record →KOYO6308
Deep groove ball bearing
View full technical record →NSK6308
Deep groove ball bearing
View full technical record →NACHI6308
Deep groove ball bearing
View full technical record →NACHI6308-2NKE9
Deep groove ball bearing
View full technical record →NACHI6308-2NSE9
Deep groove ball bearing
View full technical record →KOYO6308 2RD
Deep groove ball bearing
View full technical record →TIMKEN6308-2RS
Deep groove ball bearing
View full technical record →KOYO6308 2RS
Deep groove ball bearing
View full technical record →SKF630/8-2RS1
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.