62/28 2RS bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 62/28 2RS. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
62/28 2RS dimensions and recorded technical data
This base designation has conflicting recorded dimensions. Choose the complete brand and designation below. A single dimensional answer would hide a real difference between records.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 2 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 62/28 2RS
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO 62/28 2RS — 14 recorded parameters
Deep groove ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 28 mm |
| D | Not separately recorded | 58 mm |
| B | Not separately recorded | 16 mm |
| R(Min.) | Not separately recorded | 1 mm |
| Basic Load Ratings : Cr | Not separately recorded | 22.4 kN |
| Basic Load Ratings : C0R | Not separately recorded | 9.75 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 0.720 kN |
| Factor : F0 | Not separately recorded | 13.4 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 7600 min-1 |
| Da(Min.) | Not separately recorded | 33 mm |
| Da(Max.) | Not separately recorded | 35 mm |
| Da(Max.) | Not separately recorded | 53 mm |
| Ra(Max.) | Not separately recorded | 1 mm |
| Mass(Refer.) | Not separately recorded | 0.173 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| KOYO62/28 2RSDeep groove ball bearing |
| 22.4 kN | 9.75 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1 | 0.173 kg173 g |
| KOYO6228 2RSDeep groove ball bearing |
| 208 kN | 150 kN | — | 1600 rpmLimiting Speeds(Grease Lub.): 1600 min-1 | 7.45 kg7450 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| KOYO 62/28 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6228 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
62/28 2RS
Deep groove ball bearing
View full technical record →KOYO6228 2RS
Deep groove ball bearing
View full technical record →SKF62/28-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF62/28-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.