6207 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6207. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page7 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6207 — PEER catalogue dimensions
Independent technical reference from PEER’s historical 2009 sheets; checked 2026-10-03. These are catalogue records, not current-stock claims or replacement approvals. Printed units are kept separate.
| Full catalogue model | d×D×B (mm) | d×D×B (in) | Closed width / execution scope |
|---|---|---|---|
| PEER · 6200 series6207 | 35× | 1.3780× | Base designation only; complete closure execution must be checked |
Read ratings without transferring them to another execution
Cr and Cor are catalogue basic load ratings, not allowable application loads. Oil/grease values below are explicitly for open bearings where supplied. They are not sealed-bearing or machine operating-speed approvals. A dash means withheld or not established here.
| Model | Dynamic Cr / static Cor | Open: oil / grease | Evidence boundary |
|---|---|---|---|
| 6207 | 25700 / 15300 N | 11000 / 9300 r/min | Base-row catalogue values only; no cross-brand transfer. |
Printed decimal conversions inherit catalogue rounding; more decimal places do not create manufacturing accuracy. Special bores must not be rounded to a nearby metric bearing. The historical table does not establish an exact RS/2RS, NR, ABEC, C3, ceramic, vehicle or kit execution unless explicitly listed. No CAD or interchange approval is implied.
6207 — source-labelled NSK dimensions
Nominal dimensions from the NSK Bearing Replacement Guide, reference BRG/C/E/11.15. This is a historical catalogue reference, checked 2026-10-03; it is not a current product-availability list or an interchange approval. Each row preserves its complete printed designation.
| Complete NSK designation | Bore d | Outside D | Width B | Source page / boundary |
|---|---|---|---|---|
| NSK catalogue record6207 | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207DDU | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207DDUNR | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207DU | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207NR | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207VV | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207Z | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207ZN | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207ZNR | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207ZZ | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
| NSK catalogue record6207ZZNR | 35 mm | 72 mm | 17 mm | Printed p. 46Nominal envelope only; complete execution as marked |
Read d×D×B together. Equal outside dimensions do not prove equal seals, internal clearance, precision, load ratings, lubricant or speed limits. Those properties are not supplied by this dimensional table. A DU, DDU, Z, ZZ, VV, DD or other marking is kept as printed; missing suffix records are not created from a base model.
6207 dimensions and recorded technical data
The recorded 6207 base designation measures 35×72×17 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO, NACHI. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 163 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6207
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6207 NR — 21 dimension fields
Deep groove ball bearing with snap ring. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 72 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 17 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 46.94 mm |
| Recess diameter | D 2 | ≈ 62.69 mm |
| Diameter of snap ring groove | D 3 | 68.81 mm |
| Outside diameter of snap ring | D 4 | 78.6 mm |
| Width of snap ring groove | b | 1.9 mm |
| Distance from outer ring side face to snap ring groove | C | 3.28 mm |
| Width of snap ring | f | 1.7 mm |
| Bottom radius of snap ring groove | r 0 | max. 0.6 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 42 mm |
| Diameter of housing abutment | D a | max. 65 mm |
| Diameter of snap ring recess in the housing | D b | min. 80 mm |
| Width of snap ring recess in the housing | b a | min. 2.2 mm |
| Distance from outer ring side face to snap ring back face | C a | max. 4.98 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
SKF 6207/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 35.0 mm |
| Outside diameter | Not supplied separately | 72.0 mm |
| Width | Not supplied separately | 17.0 mm |
SKF 6207 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 72 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 17 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 46.94 mm |
| Recess diameter | D 2 | ≈ 62.69 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 42 mm |
| Diameter of housing abutment | D a | max. 65 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6207 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 60.66 mm |
| Caliber diameter outer ring | D2 | 63.34 mm |
| Shoulder diameter inner ring | d1 | 47.2 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 42 mm |
| Maximum diameter of housing shoulder | Da max | 65 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6207-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 60.66 mm |
| Caliber diameter outer ring | D2 | 63.34 mm |
| Shoulder diameter inner ring | d1 | 47.2 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 42 mm |
| Maximum diameter of housing shoulder | Da max | 65 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6207-NR — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 60.66 mm |
| Caliber diameter outer ring | D2 | 63.34 mm |
| Shoulder diameter inner ring | d1 | 47.2 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 42 mm |
| Maximum diameter of housing shoulder | Da max | 65 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6207 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
KOYO 6207 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
KOYO 6207NR — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Width | B | 17 mm |
TIMKEN 6207-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 35 mm |
| O.D. (D) | D | 72 mm / 2.835 in |
| Width (B) | B | 17 mm / 0.669 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6207 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 35 mm |
| O.D. (D) | D | 72 mm / 2.835 in |
| Width (B) | B | 17 mm / 0.669 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6207-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 35 mm |
| O.D. (D) | D | 72 mm / 2.835 in |
| Width (B) | B | 17 mm / 0.669 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6207-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 35 mm |
| O.D. (D) | D | 72 mm / 2.835 in |
| Width (B) | B | 17 mm / 0.669 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6207-NR — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 35 mm |
| O.D. (D) | D | 72 mm / 2.835 in |
| Width (B) | B | 17 mm / 0.669 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
Catalogue parameters for 6207
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 6207 — 45 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 35.0 mm |
| Outside diameter | Not separately recorded | 72.0 mm |
| Width | Not separately recorded | 17.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 27.0 kN |
| Basic static load rating | Not separately recorded | 15.3 kN |
| Reference speed | Not separately recorded | 20000.0 r/min |
| Limiting speed | Not separately recorded | 13000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 1.0 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.281 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 72 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 17 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 46.94 mm |
| Recess diameter | D 2 | ≈ 62.69 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
| ISO tolerance class for dimensions | Not separately recorded | P6 and tighter width tolerance |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 42 mm |
| Diameter of housing abutment | D a | max. 65 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 27 kN |
| Basic static load rating | C 0 | 15.3 kN |
| Fatigue load limit | P u | 0.655 kN |
| Reference speed | Not separately recorded | 20000 r/min |
| Limiting speed | Not separately recorded | 13000 r/min |
| Minimum load factor | k r | 0.03 |
| Calculation factor | f 0 | 13.8 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 10 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 13 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P6 |
FAG 6207 — 48 recorded parameters
Deep groove ball bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Bore diameter | d | 1.378 in |
| Outside diameter | D | 72 mm |
| Outside diameter | D | 2.835 in |
| Width | B | 17 mm |
| Width | B | 0.669 in |
| Basic dynamic load rating, radial | Cr | 27,500 N |
| Basic dynamic load rating, radial | Cr | 6,182.554 lbf |
| Basic static load rating, radial | C0r | 15,300 N |
| Basic static load rating, radial | C0r | 3,439.748 lbf |
| Fatigue load limit, radial | Cur | 950 N |
| Fatigue load limit, radial | Cur | 213.579 lbf |
| Limiting speed | nG | 13,800 1/min |
| Reference speed | nϑr | 10,400 1/min |
| Mass | ≈m | 0.282 kg |
| Mass | ≈m | 0.622 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 42 mm |
| Minimum diameter shaft shoulder | da min | 1.654 in |
| Maximum diameter of housing shoulder | Da max | 65 mm |
| Maximum diameter of housing shoulder | Da max | 2.559 in |
| Maximum fillet radius | ra max | 1 mm |
| Maximum fillet radius | ra max | 0.039 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension | rmin | 1.1 mm |
| Minimum chamfer dimension | rmin | 0.043 in |
| Shoulder diameter outer ring | D1 | 60.66 mm |
| Shoulder diameter outer ring | D1 | 2.388 in |
| Caliber diameter outer ring | D2 | 63.34 mm |
| Caliber diameter outer ring | D2 | 2.494 in |
| Shoulder diameter inner ring | d1 | 47.2 mm |
| Shoulder diameter inner ring | d1 | 1.858 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 120 °C |
| Operating temperature max. | Tmax | 248 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Calculation factor | f0 | 13.8 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Type of Seal | Without | Not sealed |
| Cage | JN | Steel sheet metal |
| Tolerance class | PN | Normal (ISO 492:2023) |
| Dimensional / heat stabilization | SN | Rings dimensional stabilized up to 120° |
| Lubricant | Without | Bearing not greased |
| Radial internal clearance | CN (Group N) | Normal internal clearance |
| Bore type | Z | Cylindrical |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Axial load capacity in both directions | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
KOYO 6207 — 14 recorded parameters
Deep groove ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
The plain KOYO 6207 record is open. For a sealed candidate, inspect the separate KOYO 6207 2RS record; for a shielded candidate, inspect KOYO 6207 ZZ. Both are listed in this page’s exact-designation references with their own parameters. The base number alone does not specify a closure.
These are distinct catalogue constructions, not a suggestion to add a loose seal to an open bearing. Seal replacement or removal requires the original assembly information; no loose-seal part number or equipment fitment is established by these records.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 35 mm |
| D | Not separately recorded | 72 mm |
| B | Not separately recorded | 17 mm |
| R(Min.) | Not separately recorded | 1.1 mm |
| Basic Load Ratings : Cr | Not separately recorded | 32.1 kN |
| Basic Load Ratings : C0R | Not separately recorded | 15.4 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 1.10 kN |
| Factor : F0 | Not separately recorded | 13.9 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 9200 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 11000 min-1 |
| Da(Min.) | Not separately recorded | 41.5 mm |
| Da(Max.) | Not separately recorded | 65.5 mm |
| Ra(Max.) | Not separately recorded | 1 mm |
| Mass(Refer.) | Not separately recorded | 0.288 kg |
NTN 6207LU — 20 recorded parameters
Single row deep groove ball bearings
Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.
For this exact NTN 6207LU record, the nominal envelope is 35×72×17 mm (d = internal diameter; D = external diameter; B = bearing/inner ring width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 1.377953×2.834646×0.669291 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6207LU: contact seal on one side. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Dimensions and properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Internal diameter | d | 35 mm |
| External diameter | D | 72 mm |
| Bearing/Inner ring width | B | 17 mm |
| Min fillet radius | rs | 1.1 mm |
| Radial clearance class | Not separately recorded | CN |
| Mass | Not separately recorded | 0.288 kg |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dynamic load | C | 28.4 kN |
| Static load | C0 | 15.3 kN |
| Fatigue limit load | Cu | 1.09 kN |
| Coefficient | f0 | 13.8 |
| Grease lubrication limit speed | N lim | 6300 r/min |
| Min operating temperature | Tmin | -25 °C |
| Max operating temperature | Tmax | 110 °C |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Min shoulder diameter IR | da min | 41.5 mm |
| Max shoulder diameter IR | da max | 45 mm |
| Max shoulder diameter OR | Da max | 65.5 mm |
| Max shaft & housing fillet radius | ra max | 1 mm |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue construction | Not separately recorded | Deep groove ball bearing, radial contact, pressed steel cage, contact seal on one side |
| Cage construction | Not separately recorded | pressed steel cage |
| Closure construction | Not separately recorded | contact seal on one side |
NSK 6207 — 15 recorded parameters
Single row deep groove ball bearings
Reference: NSK Rolling Bearings catalogue E1103c, Part C; source snapshot 2026-10-02.
For this exact NSK 6207 record, the nominal envelope is 35×72×17 mm (d = bore diameter; D = outside diameter; B = bearing width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 1.377953×2.834646×0.669291 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6207: Open. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Boundary dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Bearing width | B | 17 mm |
| Minimum bearing chamfer | r min. | 1.1 mm |
Load ratings
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic radial load rating | Cr | 28200 N |
| Basic static radial load rating | C0r | 15300 N |
| Equivalent-load calculation factor | f0 | 13.8 |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum shaft shoulder diameter | da min. | 41.5 mm |
| Maximum shaft shoulder diameter | da max. | 44.5 mm |
| Maximum housing shoulder diameter | Da max. | 65.5 mm |
| Maximum shaft or housing fillet radius | ra max. | 1 mm |
Lubrication-qualified speed
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting speed with grease | Not separately recorded | 11000 r/min |
| Limiting speed with oil (open bearing) | Not separately recorded | 13000 r/min |
Reference mass
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Approximate catalogue mass (open reference) | Not separately recorded | 0.284 kg |
Construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue closure construction | Not separately recorded | Open |
NACHI 6207 — 15 recorded parameters
Deep groove ball bearing
Reference: NACHI Deep Groove Ball Bearings catalogue B3402E-2; source snapshot 2026-10-02.
For this exact NACHI 6207 record, the nominal envelope is 35×72×17 mm (d = bore diameter; D = outside diameter; B = bearing width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 1.377953×2.834646×0.669291 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Recorded closure for 6207: Open. Match the entire marking, including one-sided versus two-sided closure. A shared base number does not establish the same seal or shield across brands.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Boundary dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 72 mm |
| Bearing width | B | 17 mm |
| Minimum bearing chamfer | r min. | 1.1 mm |
Load ratings
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic radial load rating | Cr | 32500 N |
| Basic static radial load rating | C0r | 15300 N |
Equivalent-load factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue load calculation factor | f0 | 13.8 |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum shaft shoulder diameter | da min. | 42 mm |
| Maximum housing shoulder diameter | Da max. | 65 mm |
| Maximum adjacent fillet radius | ra max. | 1 mm |
Construction
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Closure arrangement | Not separately recorded | Open |
| Listed closure suffix | Not separately recorded | None (open type) |
Reference mass
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue row mass (variants not individually specified) | Not separately recorded | 0.288 kg |
Lubrication-qualified speed
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting speed with grease (open) | Not separately recorded | 9800 r/min |
| Limiting speed with oil (open) | Not separately recorded | 11000 r/min |
KOYO 6207 2RS — 16 recorded parameters
Deep groove ball bearing
Reference: JTEKT / KOYO public product catalogue; source snapshot 2026-09-02.
Looking for a 6207 sealed bearing? KOYO 6207 2RS is a recorded catalogue candidate with contact seals on both sides. Its recorded nominal size is 35×72×17 mm, in the order bore d × outside diameter D × width B.
In JTEKT / KOYO Table 6-2, 2RS identifies contact seals on both sides. The corresponding one-sided code is RS. This manufacturer-specific explanation is consistent with the classification of this exact product record; it does not turn every 6207 base record into a sealed or shielded version.
Select the full marking, not the base number alone. Compare the grease-qualified speed, clearance, material and mounting dimensions of the candidate record before using it. A closure designation does not supply a waterproof rating, chemical-resistance certificate or approved replacement relationship.
The original product parameters below retain their source units. An absent or dash-valued oil speed is unknown, not zero and not permission to use the grease speed for an oil-lubricated arrangement.
Classification
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Official Category Path | Not separately recorded | Deep groove ball bearings - Single-row - Shielded/sealed type - Contact sealed |
| Official Classification 1 | Not separately recorded | Deep groove ball bearings / Single-row / Shielded/sealed type / Contact sealed |
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 35 mm |
| D | Not separately recorded | 72 mm |
| B | Not separately recorded | 17 mm |
| R(Min.) | Not separately recorded | 1.1 mm |
| Basic Load Ratings : Cr | Not separately recorded | 32.1 kN |
| Basic Load Ratings : C0R | Not separately recorded | 15.4 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 1.10 kN |
| Factor : F0 | Not separately recorded | 13.9 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 6000 min-1 |
| Da(Min.) | Not separately recorded | 41.5 mm |
| Da(Max.) | Not separately recorded | 43.5 mm |
| Da(Max.) | Not separately recorded | 65.5 mm |
| Ra(Max.) | Not separately recorded | 1 mm |
| Mass(Refer.) | Not separately recorded | 0.288 kg |
KOYO 6207 ZZ — 16 recorded parameters
Deep groove ball bearing
Reference: JTEKT / KOYO public product catalogue; source snapshot 2026-09-02.
Looking for a 6207 shielded bearing? KOYO 6207 ZZ is a recorded catalogue candidate with fixed shields on both sides. Its recorded nominal size is 35×72×17 mm, in the order bore d × outside diameter D × width B.
In JTEKT / KOYO Table 6-2, ZZ identifies fixed shields on both sides. The corresponding one-sided code is Z. This manufacturer-specific explanation is consistent with the classification of this exact product record; it does not turn every 6207 base record into a sealed or shielded version.
Select the full marking, not the base number alone. Compare the grease-qualified speed, clearance, material and mounting dimensions of the candidate record before using it. A closure designation does not supply a waterproof rating, chemical-resistance certificate or approved replacement relationship.
The original product parameters below retain their source units. An absent or dash-valued oil speed is unknown, not zero and not permission to use the grease speed for an oil-lubricated arrangement.
Classification
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Official Category Path | Not separately recorded | Deep groove ball bearings - Single-row - Shielded/sealed type - Shielded ZZ |
| Official Classification 1 | Not separately recorded | Deep groove ball bearings / Single-row / Shielded/sealed type / Shielded ZZ |
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 35 mm |
| D | Not separately recorded | 72 mm |
| B | Not separately recorded | 17 mm |
| R(Min.) | Not separately recorded | 1.1 mm |
| Basic Load Ratings : Cr | Not separately recorded | 32.1 kN |
| Basic Load Ratings : C0R | Not separately recorded | 15.4 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 1.10 kN |
| Factor : F0 | Not separately recorded | 13.9 |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 9200 min-1 |
| Da(Min.) | Not separately recorded | 41.5 mm |
| Da(Max.) | Not separately recorded | 43.5 mm |
| Da(Max.) | Not separately recorded | 65.5 mm |
| Ra(Max.) | Not separately recorded | 1 mm |
| Mass(Refer.) | Not separately recorded | 0.288 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6207Deep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.281 kg281 g |
| FAG6207Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.282 kg282 g |
| TIMKEN6207Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| NSK6207Deep groove ball bearing |
| 28.2 kN | 15.3 kN | — | — | 0.284 kg284 g |
| KOYO6207Deep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 9200 rpmLimiting Speeds(Grease Lub.): 9200 min-1Limiting Speeds(Oil Lub.): 11000 min-1 | 0.288 kg288 g |
| NACHI6207Deep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | 0.288 kg288 g |
| SKF6207-2RS1Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207-2RS1/C3Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207-2RS1/C4Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207-2RS1/GJNDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 6300 rpm | 0.288 kg288 g |
| SKF6207-2RS1KDeep groove ball bearing with tapered bore and seals on both sides |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.287 kg287 g |
| SKF6207-2RS1NDeep groove ball bearing with snap ring groove and integral sealing |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.286 kg286 g |
| SKF6207-2RS1NRDeep groove ball bearing with snap ring and integral sealing |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.288 kg288 g |
| SKF6207-2RS1NR/C3Deep groove ball bearing |
| — | — | — | — | 0.3 kg300 g |
| SKF6207-2RS1/W64Deep groove ball bearing |
| 27 kN | 15.3 kN | — | 4400 rpm | 0.305 kg305 g |
| SKF6207-2RSF/C3GJN7SKF Deep groove ball bearing for highly contaminated environments |
| 27 kN | 15.3 kN | — | 3000 rpm | 0.304 kg304 g |
| SKF6207-2RSF/C4GJN7SKF Deep groove ball bearing for highly contaminated environments |
| 27 kN | 15.3 kN | — | 3000 rpm | 0.304 kg304 g |
| SKF6207-2RSHDeep groove ball bearing with seals |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.296 kg296 g |
| SKF6207 2RSJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207 2RSNRJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.29 kg290 g |
| SKF6207-2RZ/C3GJNDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.288 kg288 g |
| SKF6207-2RZTN9/HC5C3WTHybrid ceramic deep groove ball bearing with seals on both sides |
| 25.5 kN | 15.3 kN | 24000 rpm | 13000 rpm | 0.251 kg251 g |
| SKF6207-2ZDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.293 kg293 g |
| SKF6207-2Z/C3Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.293 kg293 g |
| SKF6207-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.293 kg293 g |
| SKF6207-2Z/C3WTDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.293 kg293 g |
| SKF6207-2Z/GJNDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.29 kg290 g |
| SKF6207 2ZJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.29 kg290 g |
| SKF6207-2ZNRDeep groove ball bearing with snap ring and integral sealing |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.3 kg300 g |
| SKF6207 2ZNRJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 10000 rpm | 0.29 kg290 g |
| SKF6207-2ZTN9/HC5C3WTHybrid ceramic deep groove ball bearing with shields |
| 25.5 kN | 15.3 kN | 24000 rpm | 13000 rpm | 0.251 kg251 g |
| SKF6207-2Z/VA201Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 15.3 kN | — | 80 rpm | 0.29 kg290 g |
| SKF6207-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 15.3 kN | — | 80 rpm | 0.288 kg288 g |
| SKF6207-2Z/VA228Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 15.3 kN | — | 160 rpm | 0.29 kg290 g |
| SKF6207/AXDDeep groove ball bearing |
| 32.5 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.288 kg288 g |
| SKF6207/C3Deep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.281 kg281 g |
| SKF6207/C4Deep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.281 kg281 g |
| SKF6207 ETN9/C3VC4521Deep groove ball bearing |
| 31.2 kN | 17.6 kN | 20000 rpm | 13000 rpm | 0.263 kg263 g |
| SKF6207/HC5C3Hybrid ceramic deep groove ball bearing |
| 25.5 kN | 15.3 kN | 24000 rpm | 15000 rpm | 0.279 kg279 g |
| SKF6207 JEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.279 kg279 g |
| SKF6207 NDeep groove ball bearing with snap ring groove |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.277 kg277 g |
| SKF6207 N/C3Deep groove ball bearing with snap ring groove |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.277 kg277 g |
| SKF6207 NRDeep groove ball bearing with snap ring |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.291 kg291 g |
| SKF6207 NR/C3Deep groove ball bearing with snap ring |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.291 kg291 g |
| SKF6207 NRJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.289 kg289 g |
| SKF6207-RS1Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.282 kg282 g |
| SKF6207 RSJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | — | 6300 rpm | 0.282 kg282 g |
| SKF6207 TN9/C3Deep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.274 kg274 g |
| SKF6207 TN9/C4Deep groove ball bearings |
| — | — | — | — | 0.274 kg274 g |
| SKF6207 TN9/HC5C3Hybrid ceramic deep groove ball bearing |
| 25.5 kN | 15.3 kN | 24000 rpm | 15000 rpm | 0.241 kg241 g |
| SKF6207/VA201Deep groove ball bearing for high temperature applications |
| — | 15.3 kN | — | 80 rpm | 0.279 kg279 g |
| SKF6207-ZDeep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.285 kg285 g |
| SKF6207-Z/C3Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.285 kg285 g |
| SKF6207-Z/C3VT264Deep groove ball bearing with seals or shields |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.288 kg288 g |
| SKF6207 ZJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.282 kg282 g |
| SKF6207-ZNRDeep groove ball bearing with snap ring and integral sealing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.295 kg295 g |
| SKF6207 ZNRJEMDeep groove ball bearing |
| 27 kN | 15.3 kN | 20000 rpm | 13000 rpm | 0.288 kg288 g |
| FAG6207-2RSRDeep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-C2Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-C4Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-L038Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.32 kg320 g |
| FAG6207-2RSR-L038-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.31003 kg310.03 g |
| FAG6207-2RSR-L100-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-L138-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.31003 kg310.03 g |
| FAG6207-2RSR-L138-C4Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-L140-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-L207Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-L207-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-NDeep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.2982 kg298.2 g |
| FAG6207-2RSR-N-L038Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.29536 kg295.36 g |
| FAG6207-2RSR-NR-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.283 kg283 g |
| FAG6207-2RSR-N-W61BDeep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.288 kg288 g |
| FAG6207-2RSR-W61B-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.285 kg285 g |
| FAG6207-2ZDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.284 kg284 g |
| FAG6207-2Z-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.284 kg284 g |
| FAG6207-2Z-L038Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.3 kg300 g |
| FAG6207-2Z-L038-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.31395 kg313.95 g |
| FAG6207-2Z-L069-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.3 kg300 g |
| FAG6207-2Z-L100-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.31096 kg310.96 g |
| FAG6207-2Z-L207Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.284 kg284 g |
| FAG6207-2Z-L207-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 11700 rpm | 0.284 kg284 g |
| FAG6207-C-2BRS-L038-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 12700 rpm | 0.272 kg272 g |
| FAG6207-C-2BRS>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 12700 rpm | 0.276 kg276 g |
| FAG6207-C-2HRS-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.272 kg272 g |
| FAG6207-C-2HRS-C4>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.271 kg271 g |
| FAG6207-C-2HRS>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.272 kg272 g |
| FAG6207-C-2Z-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 12700 rpm | 0.27 kg270 g |
| FAG6207-C-2Z-L069-C4>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 12700 rpm | 0.27 kg270 g |
| FAG6207-C-2Z>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 12700 rpm | 0.27 kg270 g |
| FAG6207-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.282 kg282 g |
| FAG6207-C4Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.282 kg282 g |
| FAG6207-C-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.257 kg257 g |
| FAG6207-C-C4>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.265 kg265 g |
| FAG6207-C-CM>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.264 kg264 g |
| FAG6207-C-HRS-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.262 kg262 g |
| FAG6207-C-HRS-C4>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.263 kg263 g |
| FAG6207-C-HRS>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | — | 8600 rpm | 0.263 kg263 g |
| FAG6207-C-NR-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.274 kg274 g |
| FAG6207-C-NR>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.274 kg274 g |
| FAG6207-C>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.256 kg256 g |
| FAG6207-C-Z-C3>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.261 kg261 g |
| FAG6207-C-Z>VDeep groove ball bearing |
| 29.5 kN | 15.4 kN | 11300 rpm | 15000 rpm | 0.262 kg262 g |
| FAG6207-H-2RSR-C3>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | — | 5900 rpm | 0.301 kg301 g |
| FAG6207-H-2RSR>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | — | 5900 rpm | 0.301 kg301 g |
| FAG6207-H-2Z-C3>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | 10500 rpm | 11600 rpm | 0.299 kg299 g |
| FAG6207-H-2Z>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | 10500 rpm | 11600 rpm | 0.299 kg299 g |
| FAG6207-H-C3>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | 10500 rpm | 13600 rpm | 0.291 kg291 g |
| FAG6207-H>NDeep groove ball bearing |
| 27.06 kN | 15.33 kN | 10500 rpm | 13600 rpm | 0.291 kg291 g |
| FAG6207-MDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 17900 rpm | 0.32968 kg329.68 g |
| FAG6207-NDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.29149 kg291.49 g |
| FAG6207-N-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.28325 kg283.25 g |
| FAG6207-NRDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.288 kg288 g |
| FAG6207-NR-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.288 kg288 g |
| FAG6207-RSRDeep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.278 kg278 g |
| FAG6207-RSR-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | — | 5700 rpm | 0.29973 kg299.73 g |
| FAG6207-ZDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.279 kg279 g |
| FAG6207-Z-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.279 kg279 g |
| FAG6207-Z-NDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.3003 kg300.3 g |
| FAG6207-Z-N-C3Deep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.29744 kg297.44 g |
| FAG6207-Z-NRDeep groove ball bearing |
| 27.5 kN | 15.3 kN | 10400 rpm | 13800 rpm | 0.315 kg315 g |
| TIMKEN6207-2RSDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-C3/VSL609Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-C4Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-L671Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-NRDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS-NR-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RS/VSL609Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RZDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RZ-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-2RZ-NRDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-NRDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-NR-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-RSDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-RS-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207/VSL609Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-ZDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-Z-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-Z-NRDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-Z-NR-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-ZZDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-ZZ-C3Deep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| TIMKEN6207-ZZ-NRDeep groove ball bearing |
| 25.7 kN | 15.3 kN | — | — | 0.29 kg290 g |
| NSK6207DDUDeep groove ball bearing |
| 28.2 kN | 15.3 kN | — | — | — |
| NSK6207VVDeep groove ball bearing |
| 28.2 kN | 15.3 kN | — | — | — |
| NSK6207ZZDeep groove ball bearing |
| 28.2 kN | 15.3 kN | — | — | — |
| KOYO6207 2RDDeep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 8300 rpmLimiting Speeds(Grease Lub.): 8300 min-1 | 0.288 kg288 g |
| KOYO6207 2RSDeep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 6000 rpmLimiting Speeds(Grease Lub.): 6000 min-1 | 0.288 kg288 g |
| KOYO6207 2RUDeep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 9200 rpmLimiting Speeds(Grease Lub.): 9200 min-1 | 0.288 kg288 g |
| KOYO6207NRDeep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 9200 rpmLimiting Speeds(Grease Lub.): 9200 min-1Limiting Speeds(Oil Lub.): 11000 min-1 | 0.288 kg288 g |
| KOYO6207RDeep groove ball bearing |
| 38.7 kN | 17.5 kN | — | 9300 rpmLimiting Speeds(Grease Lub.): 9300 min-1Limiting Speeds(Oil Lub.): 11000 min-1 | 0.309 kg309 g |
| KOYO6207YR6C3Automotive bearing |
| — | — | — | — | 0.288 kg288 g |
| KOYO6207 ZZDeep groove ball bearing |
| 32.1 kN | 15.4 kN | — | 9200 rpmLimiting Speeds(Grease Lub.): 9200 min-1 | 0.288 kg288 g |
| NACHI6207-2NKE9Deep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NACHI6207-2NSE9Deep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NACHI6207NKE9Deep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NACHI6207NSE9Deep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NACHI6207ZEDeep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NACHI6207ZZEDeep groove ball bearing |
| 32.5 kN | 15.3 kN | — | — | — |
| NTN6207LUDeep groove ball bearing |
| 28.4 kN | 15.3 kN | — | — | 0.288 kg288 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6207 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6207 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6207 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6207 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6207-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1/C4 | Seal on both sides | Not recorded | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1/GJN | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1K | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1N | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1NR | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RS1NR/C3 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6207-2RS1/W64 | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Solid Oil |
| SKF 6207-2RSF/C3GJN7 | Seal on both sides | P6 and tighter width tolerance | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RSF/C4GJN7 | Seal on both sides | P6 and tighter width tolerance | C4 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RSH | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6207 2RSNRJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6207-2RZ/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2RZTN9/HC5C3WT | Seal on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6207-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2Z/C3WT | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6207-2Z/GJN | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6207-2ZNR | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6207 2ZNRJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6207-2ZTN9/HC5C3WT | Shield on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6207-2Z/VA201 | Shield on both sides | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6207-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6207-2Z/VA228 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6207/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6207/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6207/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6207 ETN9/C3VC4521 | Without | Not recorded | C3 | Non-metallic | Bearing steel | None |
| SKF 6207/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6207 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6207 N | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6207 N/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6207 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6207 NR/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6207 NRJEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6207-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6207 RSJEM | Seal on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6207 TN9/C3 | Without | Not recorded | C3 | Non-metallic | Bearing steel | None |
| SKF 6207 TN9/C4 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6207 TN9/HC5C3 | Without | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | None |
| SKF 6207/VA201 | Without | Not recorded | Multiples of C5 | Sheet metal | High temperature steel | Solid lubricant |
| SKF 6207-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6207-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6207-Z/C3VT264 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6207 ZJEM | Shield on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6207-ZNR | Shield on one side | P6 and tighter width tolerance | CN | Not recorded | Bearing steel | None |
| SKF 6207 ZNRJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6207-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-C2 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-2RSR-L100-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6207-2RSR-L138-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6207-2RSR-L138-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6207-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6207-2RSR-L207 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6207-2RSR-L207-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6207-2RSR-N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-N-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-2RSR-NR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-N-W61B | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2RSR-W61B-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6207-2Z-L100-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L100 — Grease (L100/customer specific) |
| FAG 6207-2Z-L207 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6207-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6207-C-2BRS-L038-C3>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6207-C-2BRS>V | 2BRS — Non-contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C-2HRS-C3>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C-2HRS-C4>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C-2HRS>V | 2HRS — Contact seal on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C-2Z-C3>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C-2Z-L069-C4>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6207-C-2Z>V | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6207-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-C4>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-CM>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CM (Group M) — Internal clearance limited for electric motors | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-HRS-C3>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-HRS-C4>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-HRS>V | HRS — Contact seal on one side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-NR-C3>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-NR>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C>V | Without — Not sealed | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-Z-C3>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-C-Z>V | Z — Non-contact shield on one Side | P6 — Class 6 (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6207-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6207-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6207-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6207-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6207-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-N-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-NR-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-Z-N | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-Z-N-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6207-Z-NR | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6207-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-C4 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-L671 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS-NR-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-2RZ-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-Z-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6207-ZZ-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6207DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6207VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6207ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207R | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207YR6C3 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6207 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6207ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN 6207LU | contact seal on one side | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6207
Deep groove ball bearing
View full technical record →FAG6207
Deep groove ball bearing
View full technical record →TIMKEN6207
Deep groove ball bearing
View full technical record →KOYO6207
Deep groove ball bearing
View full technical record →NSK6207
Deep groove ball bearing
View full technical record →NACHI6207
Deep groove ball bearing
View full technical record →NACHI6207-2NKE9
Deep groove ball bearing
View full technical record →NACHI6207-2NSE9
Deep groove ball bearing
View full technical record →KOYO6207 2RD
Deep groove ball bearing
View full technical record →TIMKEN6207-2RS
Deep groove ball bearing
View full technical record →KOYO6207 2RS
Deep groove ball bearing
View full technical record →SKF6207-2RS1
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.