608Z bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 608Z. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page6 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
608Z — source-labelled NSK dimensions
Nominal dimensions from the NSK Bearing Replacement Guide, reference BRG/C/E/11.15. This is a historical catalogue reference, checked 2026-10-03; it is not a current product-availability list or an interchange approval. Each row preserves its complete printed designation.
| Complete NSK designation | Bore d | Outside D | Width B | Source page / boundary |
|---|---|---|---|---|
| NSK catalogue record608Z | 8 mm | 22 mm | 7 mm | Printed p. 29Nominal envelope only; complete execution as marked |
Read d×D×B together. Equal outside dimensions do not prove equal seals, internal clearance, precision, load ratings, lubricant or speed limits. Those properties are not supplied by this dimensional table. A DU, DDU, Z, ZZ, VV, DD or other marking is kept as printed; missing suffix records are not created from a base model.
608Z dimensions and recorded technical data
The recorded 608Z base designation measures 8×22×7 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, NTN. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 7 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 608Z
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 608-Z — 51 recorded parameters
Deep groove ball bearing with seals or shields
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 8.0 mm |
| Outside diameter | Not separately recorded | 22.0 mm |
| Width | Not separately recorded | 7.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 3.45 kN |
| Basic static load rating | Not separately recorded | 1.37 kN |
| Reference speed | Not separately recorded | 75000.0 r/min |
| Limiting speed | Not separately recorded | 48000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Shield on one side |
| Sealing type | Not separately recorded | Non-contact |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.04 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.0121 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 8 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.007 to 0 mm |
| Outside diameter | D | 22 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.008 to 0 mm |
| Width | B | 7 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 12.15 mm |
| Recess diameter | D 2 | ≈ 19.2 mm |
| Chamfer dimension | r 1,2 | min. 0.3 mm |
| ISO tolerance class for dimensions | Not separately recorded | P6 and tighter width tolerance |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 10 mm |
| Diameter of shaft abutment | d a | max. 12 mm |
| Diameter of housing abutment | D a | max. 20 mm |
| Radius of shaft or housing fillet | r a | max. 0.3 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 3.45 kN |
| Basic static load rating | C 0 | 1.37 kN |
| Fatigue load limit | P u | 0.057 kN |
| Reference speed | Not separately recorded | 75000 r/min |
| Limiting speed | Not separately recorded | 48000 r/min |
| Minimum load factor | k r | 0.03 |
| Calculation factor | f 0 | 12 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 4 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 7 µm |
| Maximum axial run-out of inner ring of assembled bearing | t Sia | 7 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 6 µm |
| Perpendicularity of outer ring outside surface | t SD | 4 µm |
| Maximum axial run-out of outer ring of assembled bearing | t Sea | 8 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF608-ZDeep groove ball bearing with seals or shields |
| 3.45 kN | 1.37 kN | 75000 rpm | 48000 rpm | 0.0121 kg12.1 g |
| NTN608ZDeep groove ball bearing |
| 3.7 kN | 1.4 kN | — | — | 0.012 kg12 g |
| SKF608-ZTN9/LTDeep groove ball bearing with seals or shields |
| 3.45 kN | 1.37 kN | — | — | 0.0116 kg11.6 g |
| FAG608-Z-HLNDeep groove ball bearing |
| 3.5 kN | 1.37 kN | 31500 rpm | 47000 rpm | 0.012 kg12 g |
| NSK608ZZ1Deep groove ball bearing |
| 3.65 kN | 1.37 kN | — | — | 0.0122 kg12.2 g |
| KOYO608 ZZDeep groove ball bearing |
| 4.1 kN | 1.35 kN | — | 34000 rpmLimiting Speeds(Grease Lub.): 34000 min-1Limiting Speeds(Oil Lub.): - min-1 | 0.012 kg12 g |
| EZO608ZZDeep groove ball bearing |
| 3.3 kN | 1.37 kN | — | — | 0.0116 kg11.6 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 608-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| NTN 608Z | shield on one side | Not recorded | CN | pressed steel cage | Not recorded | Not recorded |
| SKF 608-ZTN9/LT | Shield on one side | Not recorded | CN | Non-metallic | Bearing steel | Grease |
| FAG 608-Z-HLN | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| NSK 608ZZ1 | Metal shields on both sides (ZZ1) | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 608 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| EZO 608ZZ | Two pressed-steel shields | Not recorded | Not recorded | Not recorded | High-carbon chromium bearing steel | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
608-Z
Deep groove ball bearing with seals or shields
View full technical record →NTN608Z
Deep groove ball bearing
View full technical record →FAG608-Z-HLN
Deep groove ball bearing
View full technical record →SKF608-ZTN9/LT
Deep groove ball bearing with seals or shields
View full technical record →KOYO608 ZZ
Deep groove ball bearing
View full technical record →EZO608ZZ
Deep groove ball bearing
View full technical record →NSK608ZZ1
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.