6016 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6016. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6016 dimensions and recorded technical data
The recorded 6016 base designation measures 80×125×22 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 71 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6016
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6016 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 125 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.015 to 0 mm |
| Width | B | 22 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 94.4 mm |
| Recess diameter | D 2 | ≈ 114.1 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 86 mm |
| Diameter of housing abutment | D a | max. 119 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6016 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 125 mm |
| Width | B | 22 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 110.98 mm |
| Caliber diameter outer ring | D2 | 113.7 mm |
| Shoulder diameter inner ring | d1 | 94.04 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 86 mm |
| Maximum diameter of housing shoulder | Da max | 119 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6016 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 125 mm |
| Width | B | 22 mm |
KOYO 6016 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 125 mm |
| Width | B | 22 mm |
KOYO 6016 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 80 mm |
| Outside diameter | D | 125 mm |
| Width | B | 22 mm |
TIMKEN 6016-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 125 mm / 4.921 in |
| Width (B) | B | 22 mm / 0.866 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6016-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 125 mm / 4.921 in |
| Width (B) | B | 22 mm / 0.866 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6016 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 80 mm |
| O.D. (D) | D | 125 mm / 4.921 in |
| Width (B) | B | 22 mm / 0.866 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6016Deep groove ball bearing |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.85 kg850 g |
| FAG6016Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.839 kg839 g |
| TIMKEN6016Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| NSK6016Deep groove ball bearing |
| 52.5 kN | 40 kN | — | — | 0.872 kg872 g |
| KOYO6016Deep groove ball bearing |
| 59.5 kN | 39.8 kN | — | 5300 rpmLimiting Speeds(Grease Lub.): 5300 min-1Limiting Speeds(Oil Lub.): 6300 min-1 | 0.85 kg850 g |
| SKF6016-2RS1Deep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | — | 3200 rpm | 0.869 kg869 g |
| SKF6016-2RS1/C3Deep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 3200 rpm | 0.868 kg868 g |
| SKF6016-2RS1/GJNDeep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 3200 rpm | 0.81 kg810 g |
| SKF6016 2RSJEMDeep groove ball bearing |
| 49.4 kN | 40 kN | — | 3200 rpm | 0.808 kg808 g |
| SKF6016-2ZDeep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 5600 rpm | 0.887 kg887 g |
| SKF6016-2Z/C3Deep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 5600 rpm | 0.887 kg887 g |
| SKF6016-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 5600 rpm | 0.81 kg810 g |
| SKF6016 2ZJEMDeep groove ball bearing |
| 49.4 kN | 40 kN | 11000 rpm | 5600 rpm | 0.808 kg808 g |
| SKF6016/AXDDeep groove ball bearing |
| 60.5 kN | 40 kN | 11000 rpm | 7000 rpm | 0.857 kg857 g |
| SKF6016/C3Deep groove ball bearing |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.85 kg850 g |
| SKF6016/C4Deep groove ball bearing |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.85 kg850 g |
| SKF6016 JEMDeep groove ball bearing |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.795 kg795 g |
| SKF6016 M/HC5P65HS0VG319Hybrid ceramic deep groove ball bearing |
| 47.5 kN | 40 kN | 12000 rpm | 9500 rpm | 0.862 kg862 g |
| SKF6016 NRDeep groove ball bearing with snap ring |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.836 kg836 g |
| SKF6016 NR/C3Deep groove ball bearing with snap ring |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.836 kg836 g |
| SKF6016-RS1Deep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | — | 3200 rpm | 0.805 kg805 g |
| SKF6016-ZDeep groove ball bearing with seals or shields |
| 49.4 kN | 40 kN | 11000 rpm | 7000 rpm | 0.864 kg864 g |
| FAG6016-2RSRDeep groove ball bearing |
| 51 kN | 40 kN | — | 2850 rpm | 0.895 kg895 g |
| FAG6016-2RSR-C3Deep groove ball bearing |
| 51 kN | 40 kN | — | 2850 rpm | 0.895 kg895 g |
| FAG6016-2RSR-L140Deep groove ball bearing |
| 51 kN | 40 kN | — | 2850 rpm | 0.858 kg858 g |
| FAG6016-2ZDeep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 6300 rpm | 0.893 kg893 g |
| FAG6016-2Z-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 6300 rpm | 0.893 kg893 g |
| FAG6016-2Z-L069-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 6300 rpm | 0.86 kg860 g |
| FAG6016-2Z-L140Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 6300 rpm | 0.855 kg855 g |
| FAG6016-2Z-L140-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 6300 rpm | 0.855 kg855 g |
| FAG6016-C2Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.839 kg839 g |
| FAG6016-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.839 kg839 g |
| FAG6016-C4Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.839 kg839 g |
| FAG6016-H-2RSR-SN-C3>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | — | 2850 rpm | 0.849 kg849 g |
| FAG6016-H-2RSR-SN>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | — | 2850 rpm | 0.849 kg849 g |
| FAG6016-H-2Z-SN-C3>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | 6200 rpm | 6400 rpm | 0.839 kg839 g |
| FAG6016-H-2Z-SN>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | 6200 rpm | 6400 rpm | 0.839 kg839 g |
| FAG6016-H-SN-C3>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | 6200 rpm | 7500 rpm | 0.865 kg865 g |
| FAG6016-H-SN>NDeep groove ball bearing |
| 42.33 kN | 35.64 kN | 6200 rpm | 7500 rpm | 0.865 kg865 g |
| FAG6016-MDeep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 9700 rpm | 0.84 kg840 g |
| FAG6016-M-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 9700 rpm | 0.84 kg840 g |
| FAG6016-M-C4Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 9700 rpm | 0.84 kg840 g |
| FAG6016-NDeep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.794 kg794 g |
| FAG6016-N-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.794 kg794 g |
| FAG6016-RSRDeep groove ball bearing |
| 51 kN | 40 kN | — | 2850 rpm | 0.83 kg830 g |
| FAG6016-ZDeep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.827 kg827 g |
| FAG6016-Z-C3Deep groove ball bearing |
| 51 kN | 40 kN | 6100 rpm | 7500 rpm | 0.827 kg827 g |
| TIMKEN6016-2RSDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-2RS-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-2RS-C3/VSL609Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-2RS/VSL609Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-2RZ-NRDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016M-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 1 kg1000 g |
| TIMKEN6016-NRDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-NR-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-RSDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.82 kg820 g |
| TIMKEN6016/VSL609Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-ZDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-Z-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.82 kg820 g |
| TIMKEN6016-Z-C4Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-Z-NRDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.82 kg820 g |
| TIMKEN6016-ZZDeep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| TIMKEN6016-ZZ-C3Deep groove ball bearing |
| 47.5 kN | 39.8 kN | — | — | 0.85 kg850 g |
| NSK6016DDUDeep groove ball bearing |
| 52.5 kN | 40 kN | — | — | — |
| NSK6016VVDeep groove ball bearing |
| 52.5 kN | 40 kN | — | — | — |
| NSK6016ZZDeep groove ball bearing |
| 52.5 kN | 40 kN | — | — | — |
| KOYO6016 2RSDeep groove ball bearing |
| 59.5 kN | 39.8 kN | — | 3100 rpmLimiting Speeds(Grease Lub.): 3100 min-1 | 0.85 kg850 g |
| KOYO6016 2RUDeep groove ball bearing |
| 59.5 kN | 39.8 kN | — | 5300 rpmLimiting Speeds(Grease Lub.): 5300 min-1 | 0.85 kg850 g |
| KOYO6016NRDeep groove ball bearing |
| 59.5 kN | 39.8 kN | — | 5300 rpmLimiting Speeds(Grease Lub.): 5300 min-1Limiting Speeds(Oil Lub.): 6300 min-1 | 0.85 kg850 g |
| KOYO6016 ZZDeep groove ball bearing |
| 59.5 kN | 39.8 kN | — | 5300 rpmLimiting Speeds(Grease Lub.): 5300 min-1 | 0.85 kg850 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6016 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6016 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6016 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6016 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6016 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6016-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6016-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6016-2RS1/GJN | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6016 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6016-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6016-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6016-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6016 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6016/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6016/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6016/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6016 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6016 M/HC5P65HS0VG319 | Without | Not recorded | C5H | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6016 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6016 NR/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6016-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6016-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6016-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6016-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6016-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6016-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6016-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6016-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6016-2Z-L140 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6016-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6016-C2 | Without — Not sealed | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-H-2RSR-SN-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6016-H-2RSR-SN>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6016-H-2Z-SN-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6016-H-2Z-SN>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6016-H-SN-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-H-SN>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6016-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6016-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6016-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-N-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6016-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6016-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-2RZ-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016M-C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 6016-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-Z-C4 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6016-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6016DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6016VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6016ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6016 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6016 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6016NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6016 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6016
Deep groove ball bearing
View full technical record →FAG6016
Deep groove ball bearing
View full technical record →TIMKEN6016
Deep groove ball bearing
View full technical record →KOYO6016
Deep groove ball bearing
View full technical record →NSK6016
Deep groove ball bearing
View full technical record →TIMKEN6016-2RS
Deep groove ball bearing
View full technical record →KOYO6016 2RS
Deep groove ball bearing
View full technical record →SKF6016-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6016-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →SKF6016-2RS1/GJN
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6016-2RS-C3
Deep groove ball bearing
View full technical record →TIMKEN6016-2RS-C3/VSL609
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.