Find · understand · compare
6015 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6015. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6015 dimensions and recorded technical data
The recorded 6015 base designation measures 75×115×20 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 82 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6015
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6015 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 115 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 20 mm |
| Deviation limits of ring width | t ΔBs | -0.1 to 0 mm |
| Shoulder diameter | d 1 | ≈ 87.85 mm |
| Recess diameter | D 2 | ≈ 104.9 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 81 mm |
| Diameter of housing abutment | D a | max. 109 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6015 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 115 mm |
| Width | B | 20 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 102.58 mm |
| Caliber diameter outer ring | D2 | 105.34 mm |
| Shoulder diameter inner ring | d1 | 88.05 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 81 mm |
| Maximum diameter of housing shoulder | Da max | 109 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6015 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Outside diameter | D | 115 mm |
| Width | B | 20 mm |
TIMKEN 6015 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 75 mm |
| O.D. (D) | D | 115 mm / 4.528 in |
| Width (B) | B | 20 mm / 0.787 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6015Deep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.631 kg631 g |
| FAG6015Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.615 kg615 g |
| TIMKEN6015Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| NSK6015Deep groove ball bearing |
| 43.5 kN | 33.5 kN | — | — | 0.649 kg649 g |
| KOYO6015Deep groove ball bearing |
| 49.4 kN | 33.5 kN | — | 5700 rpmLimiting Speeds(Grease Lub.): 5700 min-1Limiting Speeds(Oil Lub.): 6800 min-1 | 0.638 kg638 g |
| SKF6015-2RS1Deep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | — | 3400 rpm | 0.651 kg651 g |
| SKF6015-2RS1/C3Deep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 3400 rpm | 0.651 kg651 g |
| SKF6015-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 3400 rpm | 0.651 kg651 g |
| SKF6015-2RS2/C3GJNDeep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.669 kg669 g |
| SKF6015 2RSJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | — | 3400 rpm | 0.652 kg652 g |
| SKF6015-2ZDeep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 6000 rpm | 0.66 kg660 g |
| SKF6015-2Z/C3Deep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 6000 rpm | 0.66 kg660 g |
| SKF6015-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 6000 rpm | 0.573 kg573 g |
| SKF6015 2ZJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 6000 rpm | 0.66 kg660 g |
| SKF6015 2ZNRJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 6000 rpm | 0.6 kg600 g |
| SKF6015/AXDDeep groove ball bearing |
| 49.4 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.646 kg646 g |
| SKF6015/C3Deep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.631 kg631 g |
| SKF6015/C4Deep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.631 kg631 g |
| SKF6015/DFC135Double row deep groove ball bearing |
| 63.7 kN | 67 kN | 12000 rpm | 7500 rpm | 1.27 kg1270 g |
| SKF6015 JEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.565 kg565 g |
| SKF6015 MDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 10000 rpm | 0.721 kg721 g |
| SKF6015 M/C3Deep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 10000 rpm | 0.726 kg726 g |
| SKF6015 M/C3S0Deep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 10000 rpm | 0.726 kg726 g |
| SKF6015 M/HC5C3Hybrid ceramic deep groove ball bearing |
| 39.7 kN | 33.5 kN | 13000 rpm | 10000 rpm | 0.675 kg675 g |
| SKF6015 M/HC5C4S0Hybrid ceramic deep groove ball bearing |
| 39.7 kN | 33.5 kN | 13000 rpm | 10000 rpm | 0.675 kg675 g |
| SKF6015 NDeep groove ball bearing with snap ring groove |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.625 kg625 g |
| SKF6015 NRDeep groove ball bearing with snap ring |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.659 kg659 g |
| SKF6015 NRJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.6 kg600 g |
| SKF6015-RS1Deep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | — | 3400 rpm | 0.638 kg638 g |
| SKF6015 RSJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | — | 3400 rpm | 0.57 kg570 g |
| SKF6015-ZDeep groove ball bearing with seals or shields |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.642 kg642 g |
| SKF6015 ZJEMDeep groove ball bearing |
| 41.6 kN | 33.5 kN | 12000 rpm | 7500 rpm | 0.565 kg565 g |
| FAG6015-2RSRDeep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.678 kg678 g |
| FAG6015-2RSR-C2Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.678 kg678 g |
| FAG6015-2RSR-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.654 kg654 g |
| FAG6015-2RSR-L038Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.66 kg660 g |
| FAG6015-2RSR-L140Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.656 kg656 g |
| FAG6015-2RSR-L140-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.656 kg656 g |
| FAG6015-2RSR-L140-C4Deep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.656 kg656 g |
| FAG6015-2ZDeep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 6900 rpm | 0.676 kg676 g |
| FAG6015-2Z-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 6900 rpm | 0.676 kg676 g |
| FAG6015-2Z-L069-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 6900 rpm | 0.64 kg640 g |
| FAG6015-2Z-L140Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 6900 rpm | 0.656 kg656 g |
| FAG6015-2Z-L140-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 6900 rpm | 0.656 kg656 g |
| FAG6015-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.615 kg615 g |
| FAG6015-C4Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.615 kg615 g |
| FAG6015-H-2RSR-SN-C3>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | — | 3000 rpm | 0.612 kg612 g |
| FAG6015-H-2RSR-SN>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | — | 3000 rpm | 0.612 kg612 g |
| FAG6015-H-2Z-SN-C3>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | 6200 rpm | 6800 rpm | 0.611 kg611 g |
| FAG6015-H-2Z-SN>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | 6200 rpm | 6800 rpm | 0.611 kg611 g |
| FAG6015-H-SN-C3>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | 6200 rpm | 8000 rpm | 0.628 kg628 g |
| FAG6015-H-SN>NDeep groove ball bearing |
| 38.24 kN | 31.79 kN | 6200 rpm | 8000 rpm | 0.628 kg628 g |
| FAG6015-MDeep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 10600 rpm | 0.753 kg753 g |
| FAG6015-M-C3Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 10600 rpm | 0.753 kg753 g |
| FAG6015-M-C4Deep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 10600 rpm | 0.729 kg729 g |
| FAG6015-NDeep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.615 kg615 g |
| FAG6015-NRDeep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.658 kg658 g |
| FAG6015-RSRDeep groove ball bearing |
| 42 kN | 33.5 kN | — | 3050 rpm | 0.626 kg626 g |
| FAG6015-ZDeep groove ball bearing |
| 42 kN | 33.5 kN | 6300 rpm | 8100 rpm | 0.626 kg626 g |
| TIMKEN6015-2RSDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-2RS-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-2RS-C3/VSL609Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-2RS/VSL609Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-2RZDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015M-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.64 kg640 g |
| TIMKEN6015-NRDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-RSDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-RS-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015/VSL609Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-ZDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-Z-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-Z-NRDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-ZZDeep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| TIMKEN6015-ZZ-C3Deep groove ball bearing |
| 39.5 kN | 33.5 kN | — | — | 0.6 kg600 g |
| NSK6015DDUDeep groove ball bearing |
| 43.5 kN | 33.5 kN | — | — | — |
| NSK6015VVDeep groove ball bearing |
| 43.5 kN | 33.5 kN | — | — | — |
| NSK6015ZZDeep groove ball bearing |
| 43.5 kN | 33.5 kN | — | — | — |
| KOYO6015 2RSDeep groove ball bearing |
| 49.4 kN | 33.5 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1 | 0.638 kg638 g |
| KOYO6015 2RUDeep groove ball bearing |
| 49.4 kN | 33.5 kN | — | 5700 rpmLimiting Speeds(Grease Lub.): 5700 min-1 | 0.638 kg638 g |
| KOYO6015NRDeep groove ball bearing |
| 49.4 kN | 33.5 kN | — | 5700 rpmLimiting Speeds(Grease Lub.): 5700 min-1Limiting Speeds(Oil Lub.): 6800 min-1 | 0.638 kg638 g |
| KOYO6015 ZZDeep groove ball bearing |
| 49.4 kN | 33.5 kN | — | 5700 rpmLimiting Speeds(Grease Lub.): 5700 min-1 | 0.638 kg638 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6015 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6015 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6015 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6015 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6015 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6015-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6015-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6015-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6015-2RS2/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6015 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6015-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6015-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6015-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6015 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6015 2ZNRJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6015/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6015/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6015/C4 | Without | Not recorded | C4 | Sheet metal | Bearing steel | None |
| SKF 6015/DFC135 | Without | Not recorded | NSTD | Sheet metal | Bearing steel | None |
| SKF 6015 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6015 M | Without | P6 and tighter width tolerance | CN | Machined brass | Bearing steel | None |
| SKF 6015 M/C3 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6015 M/C3S0 | Without | Not recorded | C3 | Machined brass | Bearing steel | None |
| SKF 6015 M/HC5C3 | Without | Not recorded | C3 | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6015 M/HC5C4S0 | Without | Not recorded | C4 | Machined brass | Hybrid (ceramic balls) | None |
| SKF 6015 N | Without | P6 and tighter width tolerance | CN | Not recorded | Bearing steel | None |
| SKF 6015 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6015 NRJEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6015-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6015 RSJEM | Seal on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6015-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6015 ZJEM | Shield on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| FAG 6015-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6015-2RSR-C2 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6015-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6015-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6015-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6015-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6015-2RSR-L140-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6015-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6015-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6015-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6015-2Z-L140 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6015-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6015-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-H-2RSR-SN-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6015-H-2RSR-SN>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6015-H-2Z-SN-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6015-H-2Z-SN>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6015-H-SN-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-H-SN>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6015-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6015-M-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6015-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6015-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6015-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015M-C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 6015-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6015-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6015DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6015VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6015ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6015 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6015 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6015NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6015 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6015
Deep groove ball bearing
View full technical record →FAG6015
Deep groove ball bearing
View full technical record →TIMKEN6015
Deep groove ball bearing
View full technical record →KOYO6015
Deep groove ball bearing
View full technical record →NSK6015
Deep groove ball bearing
View full technical record →TIMKEN6015-2RS
Deep groove ball bearing
View full technical record →KOYO6015 2RS
Deep groove ball bearing
View full technical record →SKF6015-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6015-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →SKF6015-2RS1/C3GJN
Deep groove ball bearing with seals or shields
View full technical record →SKF6015-2RS2/C3GJN
Deep groove ball bearing with seals or shields
View full technical record →TIMKEN6015-2RS-C3
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.