Find · understand · compare
6011 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6011. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6011 dimensions and recorded technical data
The recorded 6011 base designation measures 55×90×18 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 86 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6011
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6011 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 55 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.012 to 0 mm |
| Outside diameter | D | 90 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.013 to 0 mm |
| Width | B | 18 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 66.3 mm |
| Recess diameter | D 2 | ≈ 81.5 mm |
| Chamfer dimension | r 1,2 | min. 1.1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 61 mm |
| Diameter of housing abutment | D a | max. 84 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6011 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 55 mm |
| Outside diameter | D | 90 mm |
| Width | B | 18 mm |
| Minimum chamfer dimension | rmin | 1.1 mm |
| Shoulder diameter outer ring | D1 | 78.86 mm |
| Caliber diameter outer ring | D2 | 81.54 mm |
| Shoulder diameter inner ring | d1 | 66.2 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 61 mm |
| Maximum diameter of housing shoulder | Da max | 84 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6011 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 55 mm |
| Outside diameter | D | 90 mm |
| Width | B | 18 mm |
KOYO 6011 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 55 mm |
| Outside diameter | D | 90 mm |
| Width | B | 18 mm |
KOYO 6011 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 55 mm |
| Outside diameter | D | 90 mm |
| Width | B | 18 mm |
TIMKEN 6011-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 55 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6011 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 55 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
TIMKEN 6011-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 55 mm |
| O.D. (D) | D | 90 mm / 3.543 in |
| Width (B) | B | 18 mm / 0.709 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.1 mm / 0.043 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6011Deep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.371 kg371 g |
| FAG6011Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.365 kg365 g |
| TIMKEN6011Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| NSK6011Deep groove ball bearing |
| 31 kN | 21.2 kN | — | — | 0.381 kg381 g |
| KOYO6011Deep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1Limiting Speeds(Oil Lub.): 8900 min-1 | 0.385 kg385 g |
| SKF6011-2RS1Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.386 kg386 g |
| SKF6011-2RS1/C3Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.386 kg386 g |
| SKF6011-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.39 kg390 g |
| SKF6011-2RS1/C3LHT22Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 4500 rpm | 0.387 kg387 g |
| SKF6011-2RS1NR/C3Deep groove ball bearing with snap ring and integral sealing |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.39 kg390 g |
| SKF6011 2RSJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.39 kg390 g |
| SKF6011 2RSNRJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.39 kg390 g |
| SKF6011-2ZDeep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 8000 rpm | 0.39 kg390 g |
| SKF6011-2Z/C3Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 8000 rpm | 0.39 kg390 g |
| SKF6011-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 8000 rpm | 0.39 kg390 g |
| SKF6011 2ZJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 8000 rpm | 0.39 kg390 g |
| SKF6011 2ZNRJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 8000 rpm | 0.39 kg390 g |
| SKF6011-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 21.2 kN | — | 60 rpm | 0.399 kg399 g |
| SKF6011/AXDDeep groove ball bearing |
| 35.8 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.383 kg383 g |
| SKF6011/C3Deep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.371 kg371 g |
| SKF6011/HC5C3Hybrid ceramic deep groove ball bearing |
| 28.1 kN | 21.2 kN | 18000 rpm | 11000 rpm | 0.336 kg336 g |
| SKF6011 JEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.38 kg380 g |
| SKF6011 NRDeep groove ball bearing with snap ring |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.386 kg386 g |
| SKF6011 NRJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.39 kg390 g |
| SKF6011-RS1Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | — | 4500 rpm | 0.376 kg376 g |
| SKF6011-RS1/C3Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.363 kg363 g |
| SKF6011-ZDeep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.379 kg379 g |
| SKF6011-Z/C3Deep groove ball bearing with seals or shields |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.379 kg379 g |
| SKF6011 ZJEMDeep groove ball bearing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.387 kg387 g |
| SKF6011-ZNR/C3Deep groove ball bearing with snap ring and integral sealing |
| 29.6 kN | 21.2 kN | 16000 rpm | 10000 rpm | 0.39 kg390 g |
| FAG6011-2RSRDeep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.389 kg389 g |
| FAG6011-2RSR-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.389 kg389 g |
| FAG6011-2RSR-L038Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.385 kg385 g |
| FAG6011-2RSR-L038-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.385 kg385 g |
| FAG6011-2RSR-L055-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.389 kg389 g |
| FAG6011-2RSR-L140Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.385 kg385 g |
| FAG6011-2RSR-L140-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.389 kg389 g |
| FAG6011-2RSR-L140-C4Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.389 kg389 g |
| FAG6011-2ZDeep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.385 kg385 g |
| FAG6011-2Z-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.385 kg385 g |
| FAG6011-2Z-L038Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.378 kg378 g |
| FAG6011-2Z-L038-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.378 kg378 g |
| FAG6011-2Z-L069-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.378 kg378 g |
| FAG6011-2Z-L140Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.385 kg385 g |
| FAG6011-2Z-L140-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 9100 rpm | 0.385 kg385 g |
| FAG6011-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.365 kg365 g |
| FAG6011-C4Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.365 kg365 g |
| FAG6011-H-2RSR-C3>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | — | 4150 rpm | 0.41 kg410 g |
| FAG6011-H-2RSR>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | — | 4150 rpm | 0.41 kg410 g |
| FAG6011-H-2Z-C3>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | 8500 rpm | 9200 rpm | 0.409 kg409 g |
| FAG6011-H-2Z>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | 8500 rpm | 9200 rpm | 0.409 kg409 g |
| FAG6011-H-C3>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | 8500 rpm | 10800 rpm | 0.385 kg385 g |
| FAG6011-H>NDeep groove ball bearing |
| 26.85 kN | 19.57 kN | 8500 rpm | 10800 rpm | 0.385 kg385 g |
| FAG6011-MDeep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 13900 rpm | 0.46 kg460 g |
| FAG6011-M-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 13900 rpm | 0.46 kg460 g |
| FAG6011-NDeep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.365 kg365 g |
| FAG6011-NRDeep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.368 kg368 g |
| FAG6011-RSRDeep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.40005 kg400.05 g |
| FAG6011-RSR-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | — | 4050 rpm | 0.39624 kg396.24 g |
| FAG6011-ZDeep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.37428 kg374.28 g |
| FAG6011-Z-C3Deep groove ball bearing |
| 30 kN | 21.2 kN | 8300 rpm | 10700 rpm | 0.42024 kg420.24 g |
| TIMKEN6011-2RSDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-2RS-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-2RS/VSL609Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-2RZ-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.36 kg360 g |
| TIMKEN6011-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-C4Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-NRDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.36 kg360 g |
| TIMKEN6011-NR-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-RSDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-RS-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-ZDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-Z-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-Z-NRDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.36 kg360 g |
| TIMKEN6011-ZZDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-ZZ-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.39 kg390 g |
| TIMKEN6011-ZZ-NRDeep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.36 kg360 g |
| TIMKEN6011-ZZ-NR-C3Deep groove ball bearing |
| 29.3 kN | 21.3 kN | — | — | 0.36 kg360 g |
| NSK6011DDUDeep groove ball bearing |
| 31 kN | 21.2 kN | — | — | — |
| NSK6011VVDeep groove ball bearing |
| 31 kN | 21.2 kN | — | — | — |
| NSK6011ZZDeep groove ball bearing |
| 31 kN | 21.2 kN | — | — | — |
| KOYO6011 2RDDeep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 6800 rpmLimiting Speeds(Grease Lub.): 6800 min-1 | 0.385 kg385 g |
| KOYO6011 2RSDeep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 4300 rpmLimiting Speeds(Grease Lub.): 4300 min-1 | 0.385 kg385 g |
| KOYO6011 2RUDeep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1 | 0.385 kg385 g |
| KOYO6011NRDeep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1Limiting Speeds(Oil Lub.): 8900 min-1 | 0.385 kg385 g |
| KOYO6011 ZZDeep groove ball bearing |
| 35.3 kN | 21.2 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1 | 0.385 kg385 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6011 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6011 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6011 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6011 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6011-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6011-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011-2RS1/C3LHT22 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011-2RS1NR/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6011 2RSNRJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6011-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6011-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6011 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6011 2ZNRJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6011-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6011/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6011/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6011/HC5C3 | Without | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | None |
| SKF 6011 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6011 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6011 NRJEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6011-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6011-RS1/C3 | Seal on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6011-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6011-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6011 ZJEM | Shield on one side | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6011-ZNR/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6011-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6011-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6011-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6011-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6011-2RSR-L055-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L055 — Grease (L055/customer specific) |
| FAG 6011-2RSR-L140 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6011-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6011-2RSR-L140-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6011-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6011-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6011-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6011-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6011-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6011-2Z-L140 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6011-2Z-L140-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6011-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6011-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6011-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6011-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6011-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6011-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6011-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6011-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6011-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-ZZ-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6011-ZZ-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6011DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6011VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6011ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6011 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
6011
Deep groove ball bearing
View full technical record →FAG6011
Deep groove ball bearing
View full technical record →TIMKEN6011
Deep groove ball bearing
View full technical record →KOYO6011
Deep groove ball bearing
View full technical record →NSK6011
Deep groove ball bearing
View full technical record →KOYO6011 2RD
Deep groove ball bearing
View full technical record →TIMKEN6011-2RS
Deep groove ball bearing
View full technical record →KOYO6011 2RS
Deep groove ball bearing
View full technical record →SKF6011-2RS1
Deep groove ball bearing with seals or shields
View full technical record →SKF6011-2RS1/C3
Deep groove ball bearing with seals or shields
View full technical record →SKF6011-2RS1/C3GJN
Deep groove ball bearing with seals or shields
View full technical record →SKF6011-2RS1/C3LHT22
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.