6010 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6010. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6010 dimensions and recorded technical data
The recorded 6010 base designation measures 50×80×16 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO, NACHI. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 101 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6010
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6010-Z — 13 dimension fields
Deep groove ball bearing with seals or shields. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 80 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 16 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 59.75 mm |
| Recess diameter | D 2 | ≈ 72.8 mm |
| Chamfer dimension | r 1,2 | min. 1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 54.6 mm |
| Diameter of shaft abutment | d a | max. 59.7 mm |
| Diameter of housing abutment | D a | max. 75.4 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
SKF 6010/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 50.0 mm |
| Outside diameter | Not supplied separately | 80.0 mm |
| Width | Not supplied separately | 16.0 mm |
SKF 6010 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 80 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 16 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 59.75 mm |
| Recess diameter | D 2 | ≈ 72.8 mm |
| Chamfer dimension | r 1,2 | min. 1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 54.6 mm |
| Diameter of housing abutment | D a | max. 75.4 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6010 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 70.2 mm |
| Caliber diameter outer ring | D2 | 72.94 mm |
| Shoulder diameter inner ring | d1 | 59.75 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 54.6 mm |
| Maximum diameter of housing shoulder | Da max | 75.4 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6010-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 70.2 mm |
| Caliber diameter outer ring | D2 | 72.94 mm |
| Shoulder diameter inner ring | d1 | 59.75 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 54.6 mm |
| Maximum diameter of housing shoulder | Da max | 75.4 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6010-Z — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 70.2 mm |
| Caliber diameter outer ring | D2 | 72.94 mm |
| Shoulder diameter inner ring | d1 | 59.75 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 54.6 mm |
| Maximum diameter of housing shoulder | Da max | 75.4 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6010 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
KOYO 6010 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
KOYO 6010 ZZ — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Outside diameter | D | 80 mm |
| Width | B | 16 mm |
TIMKEN 6010-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 50 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 16 mm / 0.630 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6010-Z — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 50 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 16 mm / 0.630 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6010 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 50 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 16 mm / 0.630 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6010-ZZ — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 50 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 16 mm / 0.630 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6010-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 50 mm |
| O.D. (D) | D | 80 mm / 3.150 in |
| Width (B) | B | 16 mm / 0.630 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
Catalogue parameters for 6010
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 6010/C3 — 21 recorded parameters
Deep groove ball bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 50.0 mm |
| Outside diameter | Not separately recorded | 80.0 mm |
| Width | Not separately recorded | 16.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 22.9 kN |
| Basic static load rating | Not separately recorded | 15.6 kN |
| Reference speed | Not separately recorded | 18000.0 r/min |
| Limiting speed | Not separately recorded | 11000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | Without |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | C3 |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 0.94 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.255 kg |
FAG 6010-C3 — 48 recorded parameters
Deep groove ball bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 50 mm |
| Bore diameter | d | 1.969 in |
| Outside diameter | D | 80 mm |
| Outside diameter | D | 3.15 in |
| Width | B | 16 mm |
| Width | B | 0.63 in |
| Basic dynamic load rating, radial | Cr | 22,000 N |
| Basic dynamic load rating, radial | Cr | 4,946.043 lbf |
| Basic static load rating, radial | C0r | 15,800 N |
| Basic static load rating, radial | C0r | 3,552.158 lbf |
| Fatigue load limit, radial | Cur | 800 N |
| Fatigue load limit, radial | Cur | 179.856 lbf |
| Limiting speed | nG | 12,200 1/min |
| Reference speed | nϑr | 8,900 1/min |
| Mass | ≈m | 0.258 kg |
| Mass | ≈m | 0.569 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 54.6 mm |
| Minimum diameter shaft shoulder | da min | 2.15 in |
| Maximum diameter of housing shoulder | Da max | 75.4 mm |
| Maximum diameter of housing shoulder | Da max | 2.969 in |
| Maximum fillet radius | ra max | 1 mm |
| Maximum fillet radius | ra max | 0.039 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension | rmin | 1 mm |
| Minimum chamfer dimension | rmin | 0.039 in |
| Shoulder diameter outer ring | D1 | 70.2 mm |
| Shoulder diameter outer ring | D1 | 2.764 in |
| Caliber diameter outer ring | D2 | 72.94 mm |
| Caliber diameter outer ring | D2 | 2.872 in |
| Shoulder diameter inner ring | d1 | 59.75 mm |
| Shoulder diameter inner ring | d1 | 2.352 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 120 °C |
| Operating temperature max. | Tmax | 248 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Calculation factor | f0 | 15.6 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Type of Seal | Without | Not sealed |
| Cage | JN | Steel sheet metal |
| Tolerance class | PN | Normal (ISO 492:2023) |
| Dimensional / heat stabilization | SN | Rings dimensional stabilized up to 120° |
| Lubricant | Without | Bearing not greased |
| Radial internal clearance | C3 (Group 3) | Internal clearance larger than CN |
| Bore type | Z | Cylindrical |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Axial load capacity in both directions | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6010Deep groove ball bearing |
| 22.9 kN | 16 kN | 18000 rpm | 11000 rpm | 0.255 kg255 g |
| FAG6010Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.258 kg258 g |
| TIMKEN6010Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| NSK6010Deep groove ball bearing |
| 24 kN | 16.6 kN | — | — | 0.261 kg261 g |
| KOYO6010Deep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 8400 rpmLimiting Speeds(Grease Lub.): 8400 min-1Limiting Speeds(Oil Lub.): 9900 min-1 | 0.261 kg261 g |
| NACHI6010Deep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | 0.264 kg264 g |
| SKF6010-2RS1Deep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.266 kg266 g |
| SKF6010-2RS1/C3Deep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.266 kg266 g |
| SKF6010-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 22.9 kN | 16 kN | — | 5000 rpm | 0.266 kg266 g |
| SKF6010-2RS1/GJNDeep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.25 kg250 g |
| SKF6010 2RSJEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.272 kg272 g |
| SKF6010 2RSNRJEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.282 kg282 g |
| SKF6010-2ZDeep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | 18000 rpm | 9000 rpm | 0.268 kg268 g |
| SKF6010-2Z/C3Deep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | 18000 rpm | 9000 rpm | 0.268 kg268 g |
| SKF6010-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 22.9 kN | 16 kN | 18000 rpm | 9000 rpm | 0.268 kg268 g |
| SKF6010-2Z/GJNDeep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | 18000 rpm | 9000 rpm | 0.27 kg270 g |
| SKF6010-2Z/HC5C3WTHybrid ceramic deep groove ball bearing with shields |
| 21.6 kN | 15.6 kN | 20000 rpm | 11000 rpm | 0.255 kg255 g |
| SKF6010 2ZJEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | 18000 rpm | 9000 rpm | 0.257 kg257 g |
| SKF6010 2ZNRJEMDeep groove ball bearing |
| 22.9 kN | 16 kN | 18000 rpm | 9000 rpm | 0.28 kg280 g |
| SKF6010-2ZTN9/HC5C3WTHybrid ceramic deep groove ball bearing with shields |
| 21.6 kN | 15.6 kN | — | 5000 rpm | 0.249 kg249 g |
| SKF6010-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 15.6 kN | — | 60 rpm | 0.268 kg268 g |
| SKF6010/AXDDeep groove ball bearing |
| 27.6 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.255 kg255 g |
| SKF6010/C3Deep groove ball bearing |
| 22.9 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.255 kg255 g |
| SKF6010 JEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.25 kg250 g |
| SKF6010 NDeep groove ball bearing with snap ring groove |
| 22.9 kN | 16 kN | 18000 rpm | 11000 rpm | 0.25 kg250 g |
| SKF6010 NRDeep groove ball bearing with snap ring |
| 22.9 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.264 kg264 g |
| SKF6010 NRJEMDeep groove ball bearing |
| 22.9 kN | 16 kN | 18000 rpm | 11000 rpm | 0.263 kg263 g |
| SKF6010-RS1Deep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.26 kg260 g |
| SKF6010 RSJEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | — | 5000 rpm | 0.266 kg266 g |
| SKF6010-ZDeep groove ball bearing with seals or shields |
| 22.9 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.261 kg261 g |
| SKF6010-Z/C3Deep groove ball bearing with seals or shields |
| 22.9 kN | 16 kN | 18000 rpm | 11000 rpm | 0.261 kg261 g |
| SKF6010 ZJEMDeep groove ball bearing |
| 22.9 kN | 15.6 kN | 18000 rpm | 11000 rpm | 0.245 kg245 g |
| FAG6010-2RSRDeep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.262 kg262 g |
| FAG6010-2RSR-C2Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.28866 kg288.66 g |
| FAG6010-2RSR-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.262 kg262 g |
| FAG6010-2RSR-L038Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.28 kg280 g |
| FAG6010-2RSR-L038-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.28 kg280 g |
| FAG6010-2RSR-L138-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.256 kg256 g |
| FAG6010-2RSR-L140-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.262 kg262 g |
| FAG6010-2RSR-L195Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.27 kg270 g |
| FAG6010-2RSR-L207Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.262 kg262 g |
| FAG6010-2ZDeep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.262 kg262 g |
| FAG6010-2Z-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.262 kg262 g |
| FAG6010-2Z-L038Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.28 kg280 g |
| FAG6010-2Z-L038-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.27234 kg272.34 g |
| FAG6010-2Z-L069-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.264 kg264 g |
| FAG6010-2Z-L138Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.264 kg264 g |
| FAG6010-2Z-L207Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.262 kg262 g |
| FAG6010-2Z-L207-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.262 kg262 g |
| FAG6010-2Z-L207-C4Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 10400 rpm | 0.267 kg267 g |
| FAG6010-C2Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.258 kg258 g |
| FAG6010-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.258 kg258 g |
| FAG6010-C4Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.26622 kg266.22 g |
| FAG6010-H-2RSR-C3>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | — | 4500 rpm | 0.254 kg254 g |
| FAG6010-H-2RSR>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | — | 4500 rpm | 0.254 kg254 g |
| FAG6010-H-2Z-C3>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | 8900 rpm | 10300 rpm | 0.254 kg254 g |
| FAG6010-H-2Z>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | 8900 rpm | 10300 rpm | 0.254 kg254 g |
| FAG6010-H-C3>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | 8900 rpm | 12200 rpm | 0.254 kg254 g |
| FAG6010-H>NDeep groove ball bearing |
| 20.77 kN | 15.6 kN | 8900 rpm | 12200 rpm | 0.254 kg254 g |
| FAG6010-MDeep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 15900 rpm | 0.33 kg330 g |
| FAG6010-M-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 15900 rpm | 0.33 kg330 g |
| FAG6010-NRDeep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.272 kg272 g |
| FAG6010-RSRDeep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.2601 kg260.1 g |
| FAG6010-RSR-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | — | 4450 rpm | 0.253 kg253 g |
| FAG6010-ZDeep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.26 kg260 g |
| FAG6010-Z-C3Deep groove ball bearing |
| 22 kN | 15.8 kN | 8900 rpm | 12200 rpm | 0.26 kg260 g |
| TIMKEN6010-2RSDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-2RS-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-2RS/VSL609Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-2RZDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| TIMKEN6010-2RZ-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| TIMKEN6010-2RZ-NRDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010HDeep groove ball bearing |
| 17.7 kN | 12.3 kN | — | — | 0.26 kg260 g |
| TIMKEN6010H/FVSL525Deep groove ball bearing |
| 17.7 kN | 12.3 kN | — | — | 0.26 kg260 g |
| TIMKEN6010H/FVSL613Deep groove ball bearing |
| 17.7 kN | 12.3 kN | — | — | 0.26 kg260 g |
| TIMKEN6010K-2RSDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| TIMKEN6010-NRDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-RSDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-RS-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-ZDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-Z-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-Z-NRDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| TIMKEN6010-Z-NR-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| TIMKEN6010-ZZDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-ZZ-C3Deep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.26 kg260 g |
| TIMKEN6010-ZZ-NRDeep groove ball bearing |
| 21.8 kN | 16.6 kN | — | — | 0.25 kg250 g |
| NSK6010DDUDeep groove ball bearing |
| 24 kN | 16.6 kN | — | — | — |
| NSK6010VVDeep groove ball bearing |
| 24 kN | 16.6 kN | — | — | — |
| NSK6010ZZDeep groove ball bearing |
| 24 kN | 16.6 kN | — | — | — |
| KOYO6010 2RDDeep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 7600 rpmLimiting Speeds(Grease Lub.): 7600 min-1 | 0.261 kg261 g |
| KOYO6010 2RSDeep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 4800 rpmLimiting Speeds(Grease Lub.): 4800 min-1 | 0.261 kg261 g |
| KOYO6010 2RUDeep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 8400 rpmLimiting Speeds(Grease Lub.): 8400 min-1 | 0.261 kg261 g |
| KOYO6010NRDeep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 8400 rpmLimiting Speeds(Grease Lub.): 8400 min-1Limiting Speeds(Oil Lub.): 9900 min-1 | 0.261 kg261 g |
| KOYO6010 ZZDeep groove ball bearing |
| 27.3 kN | 16.6 kN | — | 8400 rpmLimiting Speeds(Grease Lub.): 8400 min-1 | 0.261 kg261 g |
| NACHI6010-2NKE9Deep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
| NACHI6010-2NSE9Deep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
| NACHI6010NKE9Deep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
| NACHI6010NSE9Deep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
| NACHI6010ZEDeep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
| NACHI6010ZZEDeep groove ball bearing |
| 27.4 kN | 16.6 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6010 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6010 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6010 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6010 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6010-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6010-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6010-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6010-2RS1/GJN | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6010 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6010 2RSNRJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6010-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6010-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6010-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6010-2Z/GJN | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 6010-2Z/HC5C3WT | Shield on both sides | Not recorded | C3 | Sheet metal | Hybrid (ceramic balls) | Grease |
| SKF 6010 2ZJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6010 2ZNRJEM | Shield on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6010-2ZTN9/HC5C3WT | Shield on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6010-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6010/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6010/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6010 JEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6010 N | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6010 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6010 NRJEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6010-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6010 RSJEM | Seal on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6010-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6010-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6010 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6010-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6010-2RSR-C2 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6010-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6010-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6010-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6010-2RSR-L138-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6010-2RSR-L140-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L140 — Grease (L140/customer specific) |
| FAG 6010-2RSR-L195 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L195 — Grease (L195/customer specific) |
| FAG 6010-2RSR-L207 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6010-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6010-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6010-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6010-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6010-2Z-L069-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L069 — Low noise high-temperature grease, interchangeable with grease L207 |
| FAG 6010-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6010-2Z-L207 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6010-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6010-2Z-L207-C4 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6010-C2 | Without — Not sealed | PN — Normal (ISO 492:2023) | C2 (Group 2) — Internal clearance smaller than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6010-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6010-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6010-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6010-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-M | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6010-M-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | M — Solid brass cage, rolling element guided | Not recorded | Without — Bearing not greased |
| FAG 6010-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6010-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6010-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-2RZ | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-2RZ-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010H | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6010H/FVSL525 | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6010H/FVSL613 | Open | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6010K-2RS | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| TIMKEN 6010-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-Z-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-Z-NR-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6010-ZZ-NR | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6010DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6010VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6010ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6010 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6010ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6010
Deep groove ball bearing
View full technical record →FAG6010
Deep groove ball bearing
View full technical record →TIMKEN6010
Deep groove ball bearing
View full technical record →KOYO6010
Deep groove ball bearing
View full technical record →NSK6010
Deep groove ball bearing
View full technical record →NACHI6010
Deep groove ball bearing
View full technical record →NACHI6010-2NKE9
Deep groove ball bearing
View full technical record →NACHI6010-2NSE9
Deep groove ball bearing
View full technical record →KOYO6010 2RD
Deep groove ball bearing
View full technical record →TIMKEN6010-2RS
Deep groove ball bearing
View full technical record →KOYO6010 2RS
Deep groove ball bearing
View full technical record →SKF6010-2RS1
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.