6008 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 6008. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
6008 dimensions and recorded technical data
The recorded 6008 base designation measures 40×68×15 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF, FAG, NSK, KOYO, NACHI. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 100 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 6008
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
SKF 6008-Z — 13 dimension fields
Deep groove ball bearing with seals or shields. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 68 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 15 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 49.25 mm |
| Recess diameter | D 2 | ≈ 61.1 mm |
| Chamfer dimension | r 1,2 | min. 1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 44.6 mm |
| Diameter of shaft abutment | d a | max. 49.2 mm |
| Diameter of housing abutment | D a | max. 63.4 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
SKF 6008/C3 — 3 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
The source gives named dimensions but no drawing symbol for some values. An unqualified width is not relabelled as inner-ring B or assembly T.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not supplied separately | 40.0 mm |
| Outside diameter | Not supplied separately | 68.0 mm |
| Width | Not supplied separately | 15.0 mm |
SKF 6008 — 12 dimension fields
Deep groove ball bearing. Source: SKF product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Deviation limits of mid-range bore diameter | t Δdmp | -0.01 to 0 mm |
| Outside diameter | D | 68 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.011 to 0 mm |
| Width | B | 15 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter | d 1 | ≈ 49.25 mm |
| Recess diameter | D 2 | ≈ 61.1 mm |
| Chamfer dimension | r 1,2 | min. 1 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 44.6 mm |
| Diameter of housing abutment | D a | max. 63.4 mm |
| Radius of shaft or housing fillet | r a | max. 1 mm |
FAG 6008 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 68 mm |
| Width | B | 15 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 59.06 mm |
| Caliber diameter outer ring | D2 | 61.56 mm |
| Shoulder diameter inner ring | d1 | 49.3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 44.6 mm |
| Maximum diameter of housing shoulder | Da max | 63.4 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6008-C3 — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 68 mm |
| Width | B | 15 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 59.06 mm |
| Caliber diameter outer ring | D2 | 61.56 mm |
| Shoulder diameter inner ring | d1 | 49.3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 44.6 mm |
| Maximum diameter of housing shoulder | Da max | 63.4 mm |
| Maximum fillet radius | ra max | 1 mm |
FAG 6008-Z — 10 dimension fields
Deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 68 mm |
| Width | B | 15 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Shoulder diameter outer ring | D1 | 59.06 mm |
| Caliber diameter outer ring | D2 | 61.56 mm |
| Shoulder diameter inner ring | d1 | 49.3 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum diameter shaft shoulder | da min | 44.6 mm |
| Maximum diameter of housing shoulder | Da max | 63.4 mm |
| Maximum fillet radius | ra max | 1 mm |
KOYO 6008 — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 68 mm |
| Width | B | 15 mm |
KOYO 6008 2RS — 3 dimension fields
Deep groove ball bearing. Source: JTEKT / Koyo product catalogue; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 40 mm |
| Outside diameter | D | 68 mm |
| Width | B | 15 mm |
TIMKEN 6008-RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 68 mm / 2.677 in |
| Width (B) | B | 15 mm / 0.591 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6008-Z — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 68 mm / 2.677 in |
| Width (B) | B | 15 mm / 0.591 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6008 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 68 mm / 2.677 in |
| Width (B) | B | 15 mm / 0.591 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6008-2RS — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 68 mm / 2.677 in |
| Width (B) | B | 15 mm / 0.591 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm / 0.039 in |
TIMKEN 6008-C3 — 4 dimension fields
Deep groove ball bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
Keep the full marking shown for this record. Equal nominal dimensions do not establish matching closure, clearance, precision, material or operating limits.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 40 mm |
| O.D. (D) | D | 68 mm |
| Width (B) | B | 15 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1 mm |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF6008Deep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.185 kg185 g |
| FAG6008Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.181 kg181 g |
| TIMKEN6008Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| NSK6008Deep groove ball bearing |
| 18.4 kN | 11.5 kN | — | — | 0.19 kg190 g |
| KOYO6008Deep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 10000 rpmLimiting Speeds(Grease Lub.): 10000 min-1Limiting Speeds(Oil Lub.): 12000 min-1 | 0.192 kg192 g |
| NACHI6008Deep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | 0.194 kg194 g |
| SKF6008-2RS1Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.191 kg191 g |
| SKF6008-2RS1/C2Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.191 kg191 g |
| SKF6008-2RS1/C3Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.191 kg191 g |
| SKF6008-2RS1/C3GJNDeep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.191 kg191 g |
| SKF6008-2RS1NR/C3Deep groove ball bearing with snap ring and integral sealing |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.2 kg200 g |
| SKF6008-2RS1/W64Deep groove ball bearing |
| 17.8 kN | 11 kN | — | 4400 rpm | 0.195 kg195 g |
| SKF6008-2RSF/C3GJNSKF Deep groove ball bearing for highly contaminated environments |
| 0.018 kN | 0.012 kN | — | 3000 rpm | 0.2 kg200 g |
| SKF6008 2RSJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.191 kg191 g |
| SKF6008 2RSNRJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.2 kg200 g |
| SKF6008-2RZTN9/HC5C3WTHybrid ceramic deep groove ball bearing with seals on both sides |
| 16.8 kN | 11 kN | 24000 rpm | 13000 rpm | 0.177 kg177 g |
| SKF6008-2ZDeep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | 22000 rpm | 11000 rpm | 0.194 kg194 g |
| SKF6008-2Z/C3Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | 22000 rpm | 11000 rpm | 0.194 kg194 g |
| SKF6008-2Z/C3GJNDeep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | 22000 rpm | 11000 rpm | 0.194 kg194 g |
| SKF6008 2ZJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 11000 rpm | 0.194 kg194 g |
| SKF6008 2ZNRJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 11000 rpm | 0.203 kg203 g |
| SKF6008-2Z/VA208Deep groove ball bearing for high temperature applications with shields on both sides |
| — | 11 kN | — | 80 rpm | 0.194 kg194 g |
| SKF6008/AXDDeep groove ball bearing |
| 21.2 kN | 11 kN | 22000 rpm | 14000 rpm | 0.192 kg192 g |
| SKF6008/C3Deep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.185 kg185 g |
| SKF6008 JEMDeep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.185 kg185 g |
| SKF6008 NRDeep groove ball bearing with snap ring |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.194 kg194 g |
| SKF6008 NRJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.194 kg194 g |
| SKF6008-RS1Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.187 kg187 g |
| SKF6008-RS1/C3Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.187 kg187 g |
| SKF6008 RSJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | — | 6300 rpm | 0.187 kg187 g |
| SKF6008-ZDeep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.188 kg188 g |
| SKF6008-Z/C3Deep groove ball bearing with seals or shields |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.188 kg188 g |
| SKF6008 ZJEMDeep groove ball bearing |
| 17.8 kN | 11 kN | 22000 rpm | 14000 rpm | 0.188 kg188 g |
| FAG6008-2RSRDeep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.189 kg189 g |
| FAG6008-2RSR-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.189 kg189 g |
| FAG6008-2RSR-C4Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.2028 kg202.8 g |
| FAG6008-2RSR-L038Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.2 kg200 g |
| FAG6008-2RSR-L038-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.2 kg200 g |
| FAG6008-2RSR-L207Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.189 kg189 g |
| FAG6008-2RSR-L207-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.189 kg189 g |
| FAG6008-2ZDeep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.189 kg189 g |
| FAG6008-2Z-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.189 kg189 g |
| FAG6008-2Z-L038Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.2 kg200 g |
| FAG6008-2Z-L038-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.206 kg206 g |
| FAG6008-2Z-L138Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.192 kg192 g |
| FAG6008-2Z-L207Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.189 kg189 g |
| FAG6008-2Z-L207-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 12400 rpm | 0.189 kg189 g |
| FAG6008-C-2Z-L138-CMDeep groove ball bearing |
| 17.5 kN | 11.5 kN | 11500 rpm | 13700 rpm | 0.2 kg200 g |
| FAG6008-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.181 kg181 g |
| FAG6008-C4Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.181 kg181 g |
| FAG6008-H-2RSR-C3>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | — | 5500 rpm | 0.2 kg200 g |
| FAG6008-H-2RSR>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | — | 5500 rpm | 0.2 kg200 g |
| FAG6008-H-2Z-C3>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | 10700 rpm | 12400 rpm | 0.2 kg200 g |
| FAG6008-H-2Z>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | 10700 rpm | 12400 rpm | 0.2 kg200 g |
| FAG6008-H-C3>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | 10700 rpm | 14600 rpm | 0.194 kg194 g |
| FAG6008-H>NDeep groove ball bearing |
| 16.78 kN | 11.54 kN | 10700 rpm | 14600 rpm | 0.194 kg194 g |
| FAG6008-NDeep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.18 kg180 g |
| FAG6008-NRDeep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.181 kg181 g |
| FAG6008-RSD-TVH-L207-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.187 kg187 g |
| FAG6008-RSRDeep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.188 kg188 g |
| FAG6008-RSR-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | — | 5400 rpm | 0.19448 kg194.48 g |
| FAG6008-ZDeep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.185 kg185 g |
| FAG6008-Z-C3Deep groove ball bearing |
| 17.8 kN | 11.5 kN | 10600 rpm | 14600 rpm | 0.185 kg185 g |
| TIMKEN6008-2RSDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RS-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RS-C3/VSL609Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RS-C4Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RS-NRDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RS/VSL609Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RZ-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-2RZ-NRDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-C4Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008H-2RSDeep groove ball bearing |
| 14.3 kN | 9.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6008H-2RS/FVSL531Deep groove ball bearing |
| 14.3 kN | 9.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6008H-2RS/FVSL613Deep groove ball bearing |
| 14.3 kN | 9.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6008H-2RS/VSL609Deep groove ball bearing |
| 14.3 kN | 9.2 kN | — | — | 0.39 kg390 g |
| TIMKEN6008-NRDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-NR-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-RSDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-RS-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008/VSL609Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-ZDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-Z-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-ZZDeep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| TIMKEN6008-ZZ-C3Deep groove ball bearing |
| 16.8 kN | 11.5 kN | — | — | 0.19 kg190 g |
| NSK6008DDUDeep groove ball bearing |
| 18.4 kN | 11.5 kN | — | — | — |
| NSK6008VVDeep groove ball bearing |
| 18.4 kN | 11.5 kN | — | — | — |
| NSK6008ZZDeep groove ball bearing |
| 18.4 kN | 11.5 kN | — | — | — |
| KOYO6008 2RDDeep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 9000 rpmLimiting Speeds(Grease Lub.): 9000 min-1 | 0.192 kg192 g |
| KOYO6008 2RSDeep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 5800 rpmLimiting Speeds(Grease Lub.): 5800 min-1 | 0.192 kg192 g |
| KOYO6008 2RUDeep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 10000 rpmLimiting Speeds(Grease Lub.): 10000 min-1 | 0.192 kg192 g |
| KOYO6008NRDeep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 10000 rpmLimiting Speeds(Grease Lub.): 10000 min-1Limiting Speeds(Oil Lub.): 12000 min-1 | 0.192 kg192 g |
| KOYO6008 ZZDeep groove ball bearing |
| 20.9 kN | 11.5 kN | — | 10000 rpmLimiting Speeds(Grease Lub.): 10000 min-1 | 0.192 kg192 g |
| NACHI6008-2NKE9Deep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
| NACHI6008-2NSE9Deep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
| NACHI6008NKE9Deep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
| NACHI6008NSE9Deep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
| NACHI6008ZEDeep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
| NACHI6008ZZEDeep groove ball bearing |
| 21.1 kN | 11.5 kN | — | — | — |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 6008 | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| FAG 6008 | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6008 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6008 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 6008-2RS1 | Seal on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RS1/C2 | Seal on both sides | Not recorded | C2 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RS1/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RS1/C3GJN | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RS1NR/C3 | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RS1/W64 | Seal on both sides | Not recorded | CN | Sheet metal | Bearing steel | Solid Oil |
| SKF 6008-2RSF/C3GJN | Seal on both sides | P6 and tighter width tolerance | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008 2RSJEM | Seal on both sides | Not recorded | C3 | Not recorded | Bearing steel | Grease |
| SKF 6008 2RSNRJEM | Seal on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2RZTN9/HC5C3WT | Seal on both sides | Not recorded | C3 | Non-metallic | Hybrid (ceramic balls) | Grease |
| SKF 6008-2Z | Shield on both sides | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | Grease |
| SKF 6008-2Z/C3 | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2Z/C3GJN | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008 2ZJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008 2ZNRJEM | Shield on both sides | Not recorded | C3 | Sheet metal | Bearing steel | Grease |
| SKF 6008-2Z/VA208 | Shield on both sides | Not recorded | Multiples of C5 | Non-metallic | High temperature steel | Solid lubricant |
| SKF 6008/AXD | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6008/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6008 JEM | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6008 NR | Without | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6008 NRJEM | Without | Not recorded | C3 | Not recorded | Bearing steel | None |
| SKF 6008-RS1 | Seal on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6008-RS1/C3 | Seal on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 6008 RSJEM | Seal on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6008-Z | Shield on one side | P6 and tighter width tolerance | CN | Sheet metal | Bearing steel | None |
| SKF 6008-Z/C3 | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 6008 ZJEM | Shield on one side | Not recorded | C3 | Sheet metal | Bearing steel | None |
| FAG 6008-2RSR | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6008-2RSR-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6008-2RSR-C4 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6008-2RSR-L038 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6008-2RSR-L038-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6008-2RSR-L207 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6008-2RSR-L207-C3 | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6008-2Z | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6008-2Z-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | GA13 — Ball bearing and insert bearing grease |
| FAG 6008-2Z-L038 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6008-2Z-L038-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L038 — Grease (L038/customer specific) |
| FAG 6008-2Z-L138 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6008-2Z-L207 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6008-2Z-L207-C3 | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6008-C-2Z-L138-CM | 2Z — Non-contact shield on both sides | P6 — Class 6 (ISO 492:2023) | CM (Group M) — Internal clearance limited for electric motors | JN — Steel sheet metal | Not recorded | L138 — Grease (L138/customer specific) |
| FAG 6008-C3 | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-C4 | Without — Not sealed | PN — Normal (ISO 492:2023) | C4 (Group 4) — Internal clearance larger than C3 | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-H-2RSR-C3>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6008-H-2RSR>N | 2RSR — Contact seal on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6008-H-2Z-C3>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6008-H-2Z>N | 2Z — Non-contact shield on both sides | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Lubricating grease |
| FAG 6008-H-C3>N | Without — Not sealed | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-H>N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-N | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-NR | Without — Not sealed | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-RSD-TVH-L207-C3 | RSD — Non-contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | TVH — Solid cage made of glass-fiber reinforced polyamid PA66 | Not recorded | L207 — Low noise high-temperature grease, interchangeable with grease L069 |
| FAG 6008-RSR | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-RSR-C3 | RSR — Contact seal on one side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-Z | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | CN (Group N) — Normal internal clearance | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| FAG 6008-Z-C3 | Z — Non-contact shield on one Side | PN — Normal (ISO 492:2023) | C3 (Group 3) — Internal clearance larger than CN | JN — Steel sheet metal | Not recorded | Without — Bearing not greased |
| TIMKEN 6008-2RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RS-C3/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RS-C4 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RS-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RS/VSL609 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RZ-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-2RZ-NR | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008H-2RS | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6008H-2RS/FVSL531 | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6008H-2RS/FVSL613 | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6008H-2RS/VSL609 | Sealed | Not recorded | Not recorded | Stainless Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-NR | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-NR-C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-RS | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-RS-C3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008/VSL609 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-Z | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-Z-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-ZZ | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 6008-ZZ-C3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| NSK 6008DDU | Contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6008VV | Non-contact rubber seals on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NSK 6008ZZ | Metal shields on both sides | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008 2RD | Extremely light contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008 2RS | Contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008 2RU | Non-contact sealed | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008NR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 6008 ZZ | Shielded ZZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008-2NKE9 | Two non-contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008-2NSE9 | Two contact seals | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008NKE9 | One non-contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008NSE9 | One contact seal | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008ZE | One shield | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NACHI 6008ZZE | Two shields | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
6008
Deep groove ball bearing
View full technical record →FAG6008
Deep groove ball bearing
View full technical record →TIMKEN6008
Deep groove ball bearing
View full technical record →KOYO6008
Deep groove ball bearing
View full technical record →NSK6008
Deep groove ball bearing
View full technical record →NACHI6008
Deep groove ball bearing
View full technical record →NACHI6008-2NKE9
Deep groove ball bearing
View full technical record →NACHI6008-2NSE9
Deep groove ball bearing
View full technical record →KOYO6008 2RD
Deep groove ball bearing
View full technical record →TIMKEN6008-2RS
Deep groove ball bearing
View full technical record →KOYO6008 2RS
Deep groove ball bearing
View full technical record →SKF6008-2RS1
Deep groove ball bearing with seals or shields
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.