52210 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 52210. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
52210 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 3 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 52210
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG 52210 — 11 dimension fields
Axial deep groove ball bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Inner diameter shaft washer | d | 40 mm |
| Outer diameter housing washer | D | 78 mm |
| Height | T2 | 39 mm |
| Inner diameter housing washer | D1 | 52 mm |
| Height shaft washer | B | 9 mm |
| Minimum chamfer dimension | rmin | 1 mm |
| Minimum chamfer dimension | r1 min | 0.6 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter shaft shoulder | da max | 50 mm |
| Maximum diameter of housing shoulder | Da max | 61 mm |
| Maximum filled radius | ra max | 1 mm |
| Maximum filled radius | ra1 max | 0.6 mm |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF52210Double direction thrust ball bearing |
| 49.4 kN | 116 kN | 2400 rpm | 3400 rpm | 0.677 kg677 g |
| FAG52210Axial deep groove ball bearing |
| — | — | 5800 rpm | 4950 rpm | 0.684 kg684 g |
| NSK52210Axial deep groove ball bearing |
| — | — | — | — | 0.697 kg697 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 52210 | Not recorded | Not recorded | Not recorded | Sheet metal | Bearing steel | Not recorded |
| FAG 52210 | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | JP — Steel sheet metal | Not recorded | Not recorded |
| NSK 52210 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.