33205 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 33205. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
33205 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 8 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 33205
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG 33205 — 18 dimension fields
Tapered roller bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
For a tapered bearing, total assembly width T, inner-ring width B and outer-ring width C are different measurements. Keep the complete cup/cone or matched assembly designation; do not replace T with B when checking available axial space.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 25 mm |
| Outside diameter | D | 52 mm |
| Width, inner ring | B | 22 mm |
| Width, outer ring | C | 18 mm |
| Width, total | T | 22 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 1 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1 mm |
| Distance between the apexes of the pressure cones | a | 14 mm |
| Guidance rib diameter of inner ring | d1 | 39.6 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 30 mm |
| Minimum diameter of shaft shoulder | db min | 31 mm |
| Minimum diameter of housing shoulder | Da min | 43 mm |
| Maximum diameter of housing shoulder | Da max | 46 mm |
| Minimum diameter of housing shoulder | Db min | 49 mm |
| Minimum axial space | Ca min | 4 mm |
| Minimum axial space | Cb min | 4 mm |
| Maximum fillet radius of shaft | ra max | 1 mm |
| Maximum fillet radius of housing | rb max | 1 mm |
TIMKEN 33205 — 14 dimension fields
Tapered roller bearing. Source: Timken official dimensional catalogue; recorded snapshot 2026-10-01.
Metric and inch measurements below are the values published together in this dated manufacturer record. Their displayed rounding is retained; the inch column does not turn a metric design into an inch-series design.
This assembly is identified by cone X33205 and cup Y33205. T is the assembled width; B and C are the separate ring widths. A loose cone, a loose cup and the complete assembly are not the same item.
Shaft and housing backing-shoulder dimensions, maximum fillet radii and signed offsets answer different installation questions. Preserve the named face, limit and sign; they are not additional bearing outside diameters or nominal widths.
This factual extract is a dimensional reference, not an OEM fitment statement, a replacement approval or a downloadable CAD model.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore (d) | d | 25 mm / 0.9843 in |
| O.D. (D) | D | 52 mm / 2.0472 in |
| Width (T) | T | 22.000 mm / 0.8661 in |
| Inner Ring Width (B) | B | 22.000 mm / 0.8661 in |
| Outer Ring Width (C) | C | 18 mm / 0.7087 in |
| Effective Center Location | Not supplied separately | -7.6 mm / -0.3 in |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Max Shaft Fillet Radius | Not supplied separately | 1.020 mm / 0.040 in |
| Max Housing Fillet Radius | Not supplied separately | 1.02 mm / 0.04 in |
| Shaft Backing Shoulder Dia. - Frontface (da) | da | 30.5 mm / 1.2 in |
| Shaft Backing Shoulder Dia. - Backface (db) | db | 34 mm / 1.34 in |
| Housing Backing Shoulder Dia. - Frontface (Da) | Da | 49.53 mm / 1.95 in |
| Housing Backing Shoulder Dia. - Backface (Db) | Db | 44.45 mm / 1.75 in |
| Cage Location rel. to BF (Aa) | Aa | 0.3 mm / 0.01 in |
| Cage Location rel. to FF (Ab) | Ab | 2.5 mm / 0.1 in |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF33205Single row tapered roller bearing |
| 57.9 kN | 56 kN | 10000 rpm | 13000 rpm | 0.22 kg220 g |
| FAG33205Tapered roller bearing |
| 48.5 kN | 58 kN | 8300 rpm | 14200 rpm | 0.218 kg218 g |
| TIMKEN33205Tapered roller bearing |
| 65.4 kN | 63.6 kN | — | — | 0.23 kg230 g |
| SKF33205/VQ077Single row tapered roller bearing |
| 57.9 kN | 56 kN | 10000 rpm | 13000 rpm | 0.22 kg220 g |
| FAG33205-DYTapered roller bearing |
| 47 kN | 55 kN | 8400 rpm | 14300 rpm | 0.22 kg220 g |
| FAG33205-HTapered roller bearing |
| 46.1 kN | 58 kN | 8300 rpm | 11360 rpm | 0.2225 kg222.5 g |
| TIMKEN33205-90KA7Tapered roller bearing |
| 65.4 kN | 63.6 kN | — | — | 0.23 kg230 g |
| KOYO33205JRTapered roller bearing |
| 61.1 kN | 58.5 kN | — | 7900 rpmLimiting Speeds(Grease Lub.): 7900 min-1Limiting Speeds(Oil Lub.): 10000 min-1 | 0.225 kg225 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 33205 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| FAG 33205 | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| TIMKEN 33205 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| SKF 33205/VQ077 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| FAG 33205-DY | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 33205-H | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| TIMKEN 33205-90KA7 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 33205JR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
33205
Tapered roller bearing
View full technical record →TIMKEN33205
Tapered roller bearing
View full technical record →SKF33205
Single row tapered roller bearing
View full technical record →SKF332059
Four-row tapered roller bearing
View full technical record →TIMKEN33205-90KA7
Tapered roller bearing
View full technical record →FAG33205-DY
Tapered roller bearing
View full technical record →FAG33205-H
Tapered roller bearing
View full technical record →KOYO33205JR
Tapered roller bearing
View full technical record →SKF33205/VQ077
Single row tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.