3318 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 3318. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
3318 dimensions and recorded technical data
The recorded 3318 base designation measures 90×190×73 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from KOYO. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 6 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 3318
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
KOYO 3318 — 15 recorded parameters
Angular contact ball bearing
Reference: JTEKT / Koyo catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Technical Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| d | Not separately recorded | 90 mm |
| D | Not separately recorded | 190 mm |
| B | Not separately recorded | 73 mm |
| R(Min.) | Not separately recorded | 3 mm |
| Basic Load Ratings : Cr | Not separately recorded | 256 kN |
| Basic Load Ratings : C0R | Not separately recorded | 242 kN |
| Fatigue Load Limit : Cu | Not separately recorded | 10.6 kN |
| Limiting Speeds(Grease Lub.) | Not separately recorded | 2100 min-1 |
| Limiting Speeds(Oil Lub.) | Not separately recorded | 2800 min-1 |
| Load Center Spread : A | Not separately recorded | 125.5 mm |
| Da(Min.) | Not separately recorded | 104 mm |
| Da(Max.) | Not separately recorded | - mm |
| Da(Max.) | Not separately recorded | 176 mm |
| Ra(Max.) | Not separately recorded | 2.5 mm |
| Mass(Refer.) | Not separately recorded | 9.23 kg |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| KOYO3318Angular contact ball bearing |
| 256 kN | 242 kN | — | 2100 rpmLimiting Speeds(Grease Lub.): 2100 min-1Limiting Speeds(Oil Lub.): 2800 min-1 | 9.23 kg9230 g |
| SKF3318 ADouble row angular contact ball bearing |
| 208 kN | 180 kN | 3800 rpm | 3400 rpm | 8.54 kg8540 g |
| SKF3318 A/C3Double row angular contact ball bearing |
| 208 kN | 180 kN | 3800 rpm | 3400 rpm | 8.54 kg8540 g |
| SKF3318 A/C3VQ294Double row angular contact ball bearing |
| 195 kN | 180 kN | 3800 rpm | 3400 rpm | 8.54 kg8540 g |
| SKF3318 ATN9/C3Double row angular contact ball bearing |
| 208 kN | 180 kN | 3800 rpm | 3400 rpm | 8.1 kg8100 g |
| SKF3318 DMA/VB188Double row angular contact ball bearing with two-piece inner ring |
| 225 kN | 250 kN | 3800 rpm | 3200 rpm | 10.2 kg10200 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| KOYO 3318 | Open | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| SKF 3318 A | Without | Not recorded | Not recorded | Sheet metal | Bearing steel | None |
| SKF 3318 A/C3 | Without | Not recorded | Not recorded | Sheet metal | Bearing steel | None |
| SKF 3318 A/C3VQ294 | Without | Not recorded | Not recorded | Sheet metal | Bearing steel | None |
| SKF 3318 ATN9/C3 | Without | Not recorded | Not recorded | Non-metallic | Bearing steel | None |
| SKF 3318 DMA/VB188 | Without | Not recorded | Not recorded | Machined brass | Bearing steel | None |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
3318
Angular contact ball bearing
View full technical record →SKF3318 A
Double row angular contact ball bearing
View full technical record →SKF3318 A/C3
Double row angular contact ball bearing
View full technical record →SKF3318 A/C3VQ294
Double row angular contact ball bearing
View full technical record →SKF3318 ATN9/C3
Double row angular contact ball bearing
View full technical record →SKF3318 DMA/VB188
Double row angular contact ball bearing with two-piece inner ring
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.