32906 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 32906. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
32906 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 2 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 32906
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
FAG 32906 — 64 recorded parameters
Tapered roller bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 30 mm |
| Bore diameter | d | 1.181 in |
| Outside diameter | D | 47 mm |
| Outside diameter | D | 1.85 in |
| Width, inner ring | B | 12 mm |
| Width, inner ring | B | 0.472 in |
| Width, outer ring | C | 9 mm |
| Width, outer ring | C | 0.354 in |
| Width, total | T | 12 mm |
| Width, total | T | 0.472 in |
| Basic dynamic load rating, radial | Cr | 18,700 N |
| Basic dynamic load rating, radial | Cr | 4,204.137 lbf |
| Basic static load rating, radial | C0r | 24,900 N |
| Basic static load rating, radial | C0r | 5,598.022 lbf |
| Fatigue load limit, radial | Cur | 2,700 N |
| Fatigue load limit, radial | Cur | 607.014 lbf |
| Limiting speed | nG | 16,000 1/min |
| Thermal speed rating | nϑr | 8,200 1/min |
| Mass | ≈m | 0.075 kg |
| Mass | ≈m | 0.165 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 34 mm |
| Maximum diameter of shaft shoulder | da max | 1.339 in |
| Minimum diameter of shaft shoulder | db min | 34 mm |
| Minimum diameter of shaft shoulder | db min | 1.339 in |
| Minimum diameter of housing shoulder | Da min | 43 mm |
| Minimum diameter of housing shoulder | Da min | 1.693 in |
| Maximum diameter of housing shoulder | Da max | 43 mm |
| Maximum diameter of housing shoulder | Da max | 1.693 in |
| Minimum diameter of housing shoulder | Db min | 44 mm |
| Minimum diameter of housing shoulder | Db min | 1.732 in |
| Minimum axial space | Ca min | 2 mm |
| Minimum axial space | Ca min | 0.079 in |
| Minimum axial space | Cb min | 3 mm |
| Minimum axial space | Cb min | 0.118 in |
| Maximum fillet radius of shaft | ra max | 0.3 mm |
| Maximum fillet radius of shaft | ra max | 0.012 in |
| Maximum fillet radius of housing | rb max | 0.3 mm |
| Maximum fillet radius of housing | rb max | 0.012 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 0.3 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 0.012 in |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 0.3 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 0.012 in |
| Distance between the apexes of the pressure cones | a | 9 mm |
| Distance between the apexes of the pressure cones | a | 0.354 in |
| Guidance rib diameter of inner ring | d1 | 39.5 mm |
| Guidance rib diameter of inner ring | d1 | 1.555 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 120 °C |
| Operating temperature max. | Tmax | 248 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting value of Fa/Fr for the applicability of diff. Values of factors X and Y | e | 0.32 |
| Dynamic axial load factor | Y | 1.88 |
| Static axial load factor | Y0 | 1.04 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Tolerance class | P6X | Class 6X (ISO 492:2023) |
| Heat treatment | Not separately recorded | Standard |
| Cage | Standard | Sheet steel cage, window cage, roller-guided |
| Internal design | Not separately recorded | Standard |
| Quality level | Not separately recorded | Standard |
| Number of rows | 1 | Single-row design |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| FAG32906Tapered roller bearing |
| 18.7 kN | 24.9 kN | 8200 rpm | 16000 rpm | 0.075 kg75 g |
| FAG32906-HTapered roller bearing |
| 17.8 kN | 24.9 kN | 8200 rpm | 12800 rpm | 0.0745 kg74.5 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| FAG 32906 | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32906-H | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.