32212 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 32212. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
32212 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 18 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 32212
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG 32212-A — 18 dimension fields
Tapered roller bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
For a tapered bearing, total assembly width T, inner-ring width B and outer-ring width C are different measurements. Keep the complete cup/cone or matched assembly designation; do not replace T with B when checking available axial space.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 110 mm |
| Width, inner ring | B | 28 mm |
| Width, outer ring | C | 24 mm |
| Width, total | T | 29.75 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 2 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1.5 mm |
| Distance between the apexes of the pressure cones | a | 24 mm |
| Guidance rib diameter of inner ring | d1 | 83.7 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 69 mm |
| Minimum diameter of shaft shoulder | db min | 69 mm |
| Minimum diameter of housing shoulder | Da min | 95 mm |
| Maximum diameter of housing shoulder | Da max | 101 mm |
| Minimum diameter of housing shoulder | Db min | 104 mm |
| Minimum axial space | Ca min | 4 mm |
| Minimum axial space | Cb min | 5.5 mm |
| Maximum fillet radius of shaft | ra max | 2 mm |
| Maximum fillet radius of housing | rb max | 1.5 mm |
Catalogue parameters for 32212
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 32212 — 52 recorded parameters
Single row tapered roller bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 60.0 mm |
| Outside diameter | Not separately recorded | 110.0 mm |
| Width, total | Not separately recorded | 29.75 mm |
| Width, inner ring | Not separately recorded | 28.0 mm |
| Width, outer ring | Not separately recorded | 24.0 mm |
| Contact angle | Not separately recorded | 15.1 ° |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 155.0 kN |
| Basic static load rating | Not separately recorded | 160.0 kN |
| Reference speed | Not separately recorded | 5000.0 r/min |
| Limiting speed | Not separately recorded | 6000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Complete bearing |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Arrangement of contact angle (double-row bearing) | Not separately recorded | Not applicable |
| Matched arrangement | Not separately recorded | No |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Unit system | Not separately recorded | Metric |
| Indicative carbon footprint for new product | Not separately recorded | 4.2 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 1.13 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dimension series | Not separately recorded | 3EC |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 60 mm |
| Outside diameter | D | 110 mm |
| Bearing width, total | T | 29.75 mm |
| Shoulder diameter of inner ring | d 1 | ≈ 81.9 mm |
| Width of inner ring | B | 28 mm |
| Width of outer ring | C | 24 mm |
| Chamfer dimension of inner ring | r 1,2 | min. 2 mm |
| Chamfer dimension of outer ring | r 3,4 | min. 1.5 mm |
| Distance side face to pressure point | a | 24.05 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | max. 69 mm |
| Diameter of shaft abutment | d b | min. 70.5 mm |
| Diameter of housing abutment | D a | min. 95 mm |
| Diameter of housing abutment | D a | max. 102 mm |
| Diameter of housing abutment | D b | min. 104 mm |
| Minimum width of space required in housing on large side face | C a | min. 4 mm |
| Minimum width of space required in housing on small side face | C b | min. 5.5 mm |
| Radius of shaft fillet | r a | max. 2 mm |
| Radius of housing fillet | r b | max. 1.5 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 155 kN |
| Basic static load rating | C 0 | 160 kN |
| Fatigue load limit | P u | 18.6 kN |
| Reference speed | Not separately recorded | 5000 r/min |
| Limiting speed | Not separately recorded | 6000 r/min |
| Limiting value | e | 0.4 |
| Calculation factor | Y | 1.5 |
| Calculation factor | Y 0 | 0.8 |
NTN 32212U — 33 recorded parameters
Single row tapered roller bearings
Reference: NTN Europe public product catalogue; source snapshot 2026-10-02.
For this exact NTN 32212U record, the nominal envelope is 60×110×29.75 mm (d = internal diameter; D = external diameter; T = total width). These are bearing or washer dimensions, not shaft/housing fit limits.
Calculated inch equivalent: 2.362205×4.330709×1.171260 in, in the same axis order. The conversion uses exactly 25.4 mm per inch and rounds to six decimals; it is not an inch-series designation or a machining tolerance.
Use grease- and oil-qualified speed entries only for the named lubrication condition. Dynamic C and static C0 are catalogue ratings, not a universal safe load or installation approval; shoulder and fillet limits are separate from boundary size.
Dimensions and properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Internal diameter | d | 60 mm |
| External diameter | D | 110 mm |
| Bearing/Inner ring width | B | 28 mm |
| Outer ring width | C | 24 mm |
| Total width | T | 29.75 mm |
| External diameter inner ring | d1 | 83 mm |
| Charge load application point | a | 25 mm |
| Min fillet radius | rs | 2 mm |
| Min fillet radius | r1s | 1.5 mm |
| Mass | Not separately recorded | 1.18 kg |
| ISO 355 reference | Not separately recorded | T3EC060 |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dynamic load | C | 144 kN |
| Static load | C0 | 164 kN |
| Fatigue limit load | Cu | 20.1 kN |
| Rating life coefficient | A2 | 1 |
| Coefficient | e | 0.4 |
| Static axial load coefficient | Y0 | 0.81 |
| Upper axial load coefficient | Y2 | 1.48 |
| Oil lubrication limit speed | N lim | 4500 r/min |
| Grease lubrication limit speed | N lim | 3400 r/min |
| Min operating temperature | Tmin | -40 °C |
| Max operating temperature | Tmax | 120 °C |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Max shoulder diameter IR | da max | 69 mm |
| Min IR shoulder diameter | db min | 70 mm |
| Min shoulder diameter OR | Da min | 95 mm |
| Max shoulder diameter OR | Da max | 101.5 mm |
| Min OR shoulder diameter | Db min | 104 mm |
| Min clearance | Ca | 4 mm |
| Min clearance | Cb | 5.5 mm |
| Max fillet radius | ra max | 2 mm |
| Max fillet radius | r1a | 1.5 mm |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Catalogue construction | Not separately recorded | Tapered roller bearing, pressed steel cage |
| Cage construction | Not separately recorded | pressed steel cage |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF32212Single row tapered roller bearing |
| 155 kN | 160 kN | 5000 rpm | 6000 rpm | 1.13 kg1130 g |
| TIMKEN32212Tapered roller bearing |
| 137 kN | 160 kN | — | — | 1.14 kg1140 g |
| SKF32212/VA983Special single row tapered roller bearing |
| 141 kN | 170 kN | 4500 rpm | 6000 rpm | 1.17 kg1170 g |
| FAG32212-ATapered roller bearing |
| 133 kN | 169 kN | 3900 rpm | 6600 rpm | 1.171 kg1171 g |
| FAG32212-A>ATapered roller bearing |
| 133 kN | 169 kN | 3900 rpm | 6600 rpm | 1.163 kg1163 g |
| FAG32212-A-P5Tapered roller bearing |
| 133 kN | 169 kN | 3900 rpm | 6600 rpm | 1.161 kg1161 g |
| FAG32212-A-RTapered roller bearing |
| 133 kN | 169 kN | 3900 rpm | 6600 rpm | 1.24 kg1240 g |
| FAG32212-BTapered roller bearing |
| 128 kN | 162 kN | 3900 rpm | 6400 rpm | 1.19 kg1190 g |
| FAG32212-B-XLTapered roller bearing |
| 158 kN | 162 kN | 3900 rpm | 7700 rpm | 1.19 kg1190 g |
| FAG32212-DYTapered roller bearing |
| 124 kN | 155 kN | 4000 rpm | 6600 rpm | 1.152 kg1152 g |
| FAG32212-HTapered roller bearing |
| 126 kN | 169 kN | 3900 rpm | 5280 rpm | 1.18 kg1180 g |
| FAG32212-XLTapered roller bearing |
| 166 kN | 171 kN | 3850 rpm | 8000 rpm | 1.18 kg1180 g |
| TIMKEN32212-9X025Tapered roller bearing |
| 163 kN | 160 kN | — | — | 1.13 kg1130 g |
| TIMKEN32212SATapered roller bearing |
| 176 kN | 178 kN | — | — | 1.16 kg1160 g |
| KOYO32212CRTapered roller bearing |
| 160 kN | 164 kN | — | 3600 rpmLimiting Speeds(Grease Lub.): 3600 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 1.2 kg1200 g |
| KOYO32212JRTapered roller bearing |
| 164 kN | 167 kN | — | 3500 rpmLimiting Speeds(Grease Lub.): 3500 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 1.19 kg1190 g |
| KOYO32212JRYA1Automotive bearing |
| — | — | — | — | 1.16 kg1160 g |
| NTN32212UTapered roller bearing |
| 144 kN | 164 kN | — | — | 1.18 kg1180 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 32212 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| TIMKEN 32212 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| SKF 32212/VA983 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| FAG 32212-A | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-A>A | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-A-P5 | Not recorded | P5 — Class 5 (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-A-R | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-B | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-B-XL | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-DY | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-H | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32212-XL | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| TIMKEN 32212-9X025 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32212SA | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 32212CR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 32212JR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 32212JRYA1 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| NTN 32212U | Not recorded | Not recorded | Not recorded | pressed steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
32212
Tapered roller bearing
View full technical record →SKF32212
Single row tapered roller bearing
View full technical record →TIMKEN32212-9X025
Tapered roller bearing
View full technical record →FAG32212-A
Tapered roller bearing
View full technical record →FAG32212-A>A
Tapered roller bearing
View full technical record →FAG32212-A-P5
Tapered roller bearing
View full technical record →FAG32212-A-R
Tapered roller bearing
View full technical record →FAG32212-B
Tapered roller bearing
View full technical record →FAG32212-B-XL
Tapered roller bearing
View full technical record →KOYO32212CR
Tapered roller bearing
View full technical record →FAG32212-DY
Tapered roller bearing
View full technical record →FAG32212-H
Tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.