32014 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 32014. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
32014 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 16 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 32014
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG 32014-X — 18 dimension fields
Tapered roller bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
For a tapered bearing, total assembly width T, inner-ring width B and outer-ring width C are different measurements. Keep the complete cup/cone or matched assembly designation; do not replace T with B when checking available axial space.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 70 mm |
| Outside diameter | D | 110 mm |
| Width, inner ring | B | 25 mm |
| Width, outer ring | C | 19 mm |
| Width, total | T | 25 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 1.5 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1.5 mm |
| Distance between the apexes of the pressure cones | a | 24 mm |
| Guidance rib diameter of inner ring | d1 | 92 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 78 mm |
| Minimum diameter of shaft shoulder | db min | 77 mm |
| Minimum diameter of housing shoulder | Da min | 98 mm |
| Maximum diameter of housing shoulder | Da max | 103 mm |
| Minimum diameter of housing shoulder | Db min | 105 mm |
| Minimum axial space | Ca min | 5 mm |
| Minimum axial space | Cb min | 6 mm |
| Maximum fillet radius of shaft | ra max | 1.5 mm |
| Maximum fillet radius of housing | rb max | 1.5 mm |
Catalogue parameters for 32014
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
FAG 32014-X — 63 recorded parameters
Tapered roller bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 70 mm |
| Bore diameter | d | 2.756 in |
| Outside diameter | D | 110 mm |
| Outside diameter | D | 4.331 in |
| Width, inner ring | B | 25 mm |
| Width, inner ring | B | 0.984 in |
| Width, outer ring | C | 19 mm |
| Width, outer ring | C | 0.748 in |
| Width, total | T | 25 mm |
| Width, total | T | 0.984 in |
| Basic dynamic load rating, radial | Cr | 104,000 N |
| Basic dynamic load rating, radial | Cr | 23,381.295 lbf |
| Basic static load rating, radial | C0r | 159,000 N |
| Basic static load rating, radial | C0r | 35,746.403 lbf |
| Fatigue load limit, radial | Cur | 20,500 N |
| Fatigue load limit, radial | Cur | 4,608.813 lbf |
| Limiting speed | nG | 6,300 1/min |
| Thermal speed rating | nϑr | 3,800 1/min |
| Mass | ≈m | 0.88 kg |
| Mass | ≈m | 1.94 lbs |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 78 mm |
| Maximum diameter of shaft shoulder | da max | 3.071 in |
| Minimum diameter of shaft shoulder | db min | 77 mm |
| Minimum diameter of shaft shoulder | db min | 3.031 in |
| Minimum diameter of housing shoulder | Da min | 98 mm |
| Minimum diameter of housing shoulder | Da min | 3.858 in |
| Maximum diameter of housing shoulder | Da max | 103 mm |
| Maximum diameter of housing shoulder | Da max | 4.055 in |
| Minimum diameter of housing shoulder | Db min | 105 mm |
| Minimum diameter of housing shoulder | Db min | 4.134 in |
| Minimum axial space | Ca min | 5 mm |
| Minimum axial space | Ca min | 0.197 in |
| Minimum axial space | Cb min | 6 mm |
| Minimum axial space | Cb min | 0.236 in |
| Maximum fillet radius of shaft | ra max | 1.5 mm |
| Maximum fillet radius of shaft | ra max | 0.059 in |
| Maximum fillet radius of housing | rb max | 1.5 mm |
| Maximum fillet radius of housing | rb max | 0.059 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 1.5 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 0.059 in |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1.5 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 0.059 in |
| Distance between the apexes of the pressure cones | a | 24 mm |
| Distance between the apexes of the pressure cones | a | 0.945 in |
| Guidance rib diameter of inner ring | d1 | 92 mm |
| Guidance rib diameter of inner ring | d1 | 3.622 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 120 °C |
| Operating temperature max. | Tmax | 248 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting value of Fa/Fr for the applicability of diff. Values of factors X and Y | e | 0.43 |
| Dynamic axial load factor | Y | 1.38 |
| Static axial load factor | Y0 | 0.76 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Tolerance class | P6X | Class 6X (ISO 492:2023) |
| Heat treatment | Not separately recorded | Standard |
| Cage | Standard | Sheet steel cage, window cage, roller-guided |
| Quality level | Not separately recorded | Standard |
| Number of rows | 1 | Single-row design |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
SKF 32014 X — 52 recorded parameters
Single row tapered roller bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 70.0 mm |
| Outside diameter | Not separately recorded | 110.0 mm |
| Width, total | Not separately recorded | 25.0 mm |
| Width, inner ring | Not separately recorded | 25.0 mm |
| Width, outer ring | Not separately recorded | 19.0 mm |
| Contact angle | Not separately recorded | 16.2 ° |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 125.0 kN |
| Basic static load rating | Not separately recorded | 153.0 kN |
| Reference speed | Not separately recorded | 4500.0 r/min |
| Limiting speed | Not separately recorded | 5600.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Complete bearing |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Arrangement of contact angle (double-row bearing) | Not separately recorded | Not applicable |
| Matched arrangement | Not separately recorded | No |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Unit system | Not separately recorded | Metric |
| Indicative carbon footprint for new product | Not separately recorded | 3.1 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.84 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dimension series | Not separately recorded | 4CC |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 70 mm |
| Outside diameter | D | 110 mm |
| Bearing width, total | T | 25 mm |
| Shoulder diameter of inner ring | d 1 | ≈ 89.95 mm |
| Width of inner ring | B | 25 mm |
| Width of outer ring | C | 19 mm |
| Chamfer dimension of inner ring | r 1,2 | min. 1.5 mm |
| Chamfer dimension of outer ring | r 3,4 | min. 1.5 mm |
| Distance side face to pressure point | a | 23.4 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | max. 78 mm |
| Diameter of shaft abutment | d b | min. 79.5 mm |
| Diameter of housing abutment | D a | min. 98 mm |
| Diameter of housing abutment | D a | max. 101.5 mm |
| Diameter of housing abutment | D b | min. 105 mm |
| Minimum width of space required in housing on large side face | C a | min. 5 mm |
| Minimum width of space required in housing on small side face | C b | min. 6 mm |
| Radius of shaft fillet | r a | max. 1.5 mm |
| Radius of housing fillet | r b | max. 1.5 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 125 kN |
| Basic static load rating | C 0 | 153 kN |
| Fatigue load limit | P u | 17.3 kN |
| Reference speed | Not separately recorded | 4500 r/min |
| Limiting speed | Not separately recorded | 5600 r/min |
| Limiting value | e | 0.43 |
| Calculation factor | Y | 1.4 |
| Calculation factor | Y 0 | 0.8 |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF32014 XSingle row tapered roller bearing |
| 125 kN | 153 kN | 4500 rpm | 5600 rpm | 0.84 kg840 g |
| SKF32014 X/DFMatched tapered roller bearings arranged face-to-face |
| 214 kN | 305 kN | 3800 rpm | 5600 rpm | 1.76 kg1760 g |
| SKF32014 X/DFC150Matched tapered roller bearings arranged face-to-face |
| 214 kN | 305 kN | 3800 rpm | 5600 rpm | 1.74 kg1740 g |
| SKF32014 X/DFC220Matched tapered roller bearings arranged face-to-face |
| 214 kN | 305 kN | 3800 rpm | 5600 rpm | 1.76 kg1760 g |
| SKF32014 X/VA983Special single row tapered roller bearing |
| 106 kN | 150 kN | 4300 rpm | 5600 rpm | 0.84 kg840 g |
| FAG32014-XTapered roller bearing |
| 104 kN | 159 kN | 3800 rpm | 6300 rpm | 0.88 kg880 g |
| FAG32014-X-HTapered roller bearing |
| 98.8 kN | 159 kN | 3800 rpm | 5040 rpm | 0.88 kg880 g |
| FAG32014-X-RTapered roller bearing |
| 104 kN | 159 kN | 3800 rpm | 6300 rpm | 0.881 kg881 g |
| FAG32014-X-S1Tapered roller bearing |
| 104 kN | 159 kN | 3800 rpm | 6300 rpm | 0.88 kg880 g |
| FAG32014-X-XLTapered roller bearing |
| 129 kN | 159 kN | 3800 rpm | 7600 rpm | 0.899 kg899 g |
| FAG32014-X-XL-P5Tapered roller bearing |
| 129 kN | 159 kN | 3800 rpm | 7600 rpm | 0.875 kg875 g |
| TIMKEN32014XTapered roller bearing |
| 133 kN | 163 kN | — | — | 0.86 kg860 g |
| TIMKEN32014X-99E60Tapered roller bearing |
| 133 kN | 163 kN | — | — | 0.86 kg860 g |
| TIMKEN32014X-9X044Tapered roller bearing |
| 133 kN | 163 kN | — | — | 0.86 kg860 g |
| TIMKEN32014XQTapered roller bearing |
| 133 kN | 163 kN | — | — | 0.86 kg860 g |
| KOYO32014JRTapered roller bearing |
| 136 kN | 163 kN | — | 3300 rpmLimiting Speeds(Grease Lub.): 3300 min-1Limiting Speeds(Oil Lub.): 4400 min-1 | 0.884 kg884 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 32014 X | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32014 X/DF | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32014 X/DFC150 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32014 X/DFC220 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32014 X/VA983 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| FAG 32014-X | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32014-X-H | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32014-X-R | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32014-X-S1 | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32014-X-XL | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32014-X-XL-P5 | Not recorded | P5 — Class 5 (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| TIMKEN 32014X | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32014X-99E60 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32014X-9X044 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32014XQ | Open | ABMA Class N | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 32014JR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
32014JR
Tapered roller bearing
View full technical record →FAG32014-X
Tapered roller bearing
View full technical record →TIMKEN32014X
Tapered roller bearing
View full technical record →SKF32014 X
Single row tapered roller bearing
View full technical record →TIMKEN32014X-99E60
Tapered roller bearing
View full technical record →TIMKEN32014X-9X044
Tapered roller bearing
View full technical record →SKF32014 X/DF
Matched tapered roller bearings arranged face-to-face
View full technical record →SKF32014 X/DFC150
Matched tapered roller bearings arranged face-to-face
View full technical record →SKF32014 X/DFC220
Matched tapered roller bearings arranged face-to-face
View full technical record →FAG32014-X-H
Tapered roller bearing
View full technical record →TIMKEN32014XQ
Tapered roller bearing
View full technical record →FAG32014-X-R
Tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.