32007 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 32007. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
32007 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 15 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 32007
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
FAG 32007-X — 18 dimension fields
Tapered roller bearing. Source: Schaeffler medias — FAG; recorded snapshot 2026-09-02.
For a tapered bearing, total assembly width T, inner-ring width B and outer-ring width C are different measurements. Keep the complete cup/cone or matched assembly designation; do not replace T with B when checking available axial space.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 62 mm |
| Width, inner ring | B | 18 mm |
| Width, outer ring | C | 14 mm |
| Width, total | T | 18 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 1 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1 mm |
| Distance between the apexes of the pressure cones | a | 15 mm |
| Guidance rib diameter of inner ring | d1 | 50 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 40 mm |
| Minimum diameter of shaft shoulder | db min | 41 mm |
| Minimum diameter of housing shoulder | Da min | 54 mm |
| Maximum diameter of housing shoulder | Da max | 56 mm |
| Minimum diameter of housing shoulder | Db min | 59 mm |
| Minimum axial space | Ca min | 4 mm |
| Minimum axial space | Cb min | 4 mm |
| Maximum fillet radius of shaft | ra max | 1 mm |
| Maximum fillet radius of housing | rb max | 1 mm |
Catalogue parameters for 32007
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
FAG 32007-X — 63 recorded parameters
Tapered roller bearing
Reference: Schaeffler medias — FAG; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Main Dimensions & Performance Data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Bore diameter | d | 1.378 in |
| Outside diameter | D | 62 mm |
| Outside diameter | D | 2.441 in |
| Width, inner ring | B | 18 mm |
| Width, inner ring | B | 0.709 in |
| Width, outer ring | C | 14 mm |
| Width, outer ring | C | 0.551 in |
| Width, total | T | 18 mm |
| Width, total | T | 0.709 in |
| Basic dynamic load rating, radial | Cr | 45,500 N |
| Basic dynamic load rating, radial | Cr | 10,229.317 lbf |
| Basic static load rating, radial | C0r | 57,000 N |
| Basic static load rating, radial | C0r | 12,814.748 lbf |
| Fatigue load limit, radial | Cur | 6,800 N |
| Fatigue load limit, radial | Cur | 1,528.777 lbf |
| Limiting speed | nG | 11,600 1/min |
| Thermal speed rating | nϑr | 7,000 1/min |
| Mass | ≈m | 226 g |
| Mass | ≈m | 7.972 oz |
Mounting dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Maximum diameter of shaft shoulder | da max | 40 mm |
| Maximum diameter of shaft shoulder | da max | 1.575 in |
| Minimum diameter of shaft shoulder | db min | 41 mm |
| Minimum diameter of shaft shoulder | db min | 1.614 in |
| Minimum diameter of housing shoulder | Da min | 54 mm |
| Minimum diameter of housing shoulder | Da min | 2.126 in |
| Maximum diameter of housing shoulder | Da max | 56 mm |
| Maximum diameter of housing shoulder | Da max | 2.205 in |
| Minimum diameter of housing shoulder | Db min | 59 mm |
| Minimum diameter of housing shoulder | Db min | 2.323 in |
| Minimum axial space | Ca min | 4 mm |
| Minimum axial space | Ca min | 0.157 in |
| Minimum axial space | Cb min | 4 mm |
| Minimum axial space | Cb min | 0.157 in |
| Maximum fillet radius of shaft | ra max | 1 mm |
| Maximum fillet radius of shaft | ra max | 0.039 in |
| Maximum fillet radius of housing | rb max | 1 mm |
| Maximum fillet radius of housing | rb max | 0.039 in |
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 1 mm |
| Minimum chamfer dimension of inner ring back face | r1, 2 min | 0.039 in |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 1 mm |
| Minimum chamfer dimension of outer ring back face | r3, 4 min | 0.039 in |
| Distance between the apexes of the pressure cones | a | 15 mm |
| Distance between the apexes of the pressure cones | a | 0.591 in |
| Guidance rib diameter of inner ring | d1 | 50 mm |
| Guidance rib diameter of inner ring | d1 | 1.969 in |
Temperature range
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Operating temperature min. | Tmin | -30 °C |
| Operating temperature min. | Tmin | -22 °F |
| Operating temperature max. | Tmax | 120 °C |
| Operating temperature max. | Tmax | 248 °F |
Calculation factors
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Limiting value of Fa/Fr for the applicability of diff. Values of factors X and Y | e | 0.45 |
| Dynamic axial load factor | Y | 1.32 |
| Static axial load factor | Y0 | 0.73 |
Product characteristics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Tolerance class | P6X | Class 6X (ISO 492:2023) |
| Heat treatment | Not separately recorded | Standard |
| Cage | Standard | Sheet steel cage, window cage, roller-guided |
| Quality level | Not separately recorded | Standard |
| Number of rows | 1 | Single-row design |
Capabilities & suitability
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Radial load capacity | Not separately recorded | Yes |
| Axial load capacity in one direction | Not separately recorded | Yes |
| Suitable for grease lubrication | Not separately recorded | Yes |
| Suitable for oil lubrication | Not separately recorded | Yes |
| Unsealed design | Not separately recorded | Yes |
SKF 32007 X — 52 recorded parameters
Single row tapered roller bearing
Reference: SKF product catalogue; source snapshot 2026-09-02.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 35.0 mm |
| Outside diameter | Not separately recorded | 62.0 mm |
| Width, total | Not separately recorded | 18.0 mm |
| Width, inner ring | Not separately recorded | 18.0 mm |
| Width, outer ring | Not separately recorded | 14.0 mm |
| Contact angle | Not separately recorded | 16.8 ° |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 52.3 kN |
| Basic static load rating | Not separately recorded | 54.0 kN |
| Reference speed | Not separately recorded | 8500.0 r/min |
| Limiting speed | Not separately recorded | 10000.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bearing part | Not separately recorded | Complete bearing |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Arrangement of contact angle (double-row bearing) | Not separately recorded | Not applicable |
| Matched arrangement | Not separately recorded | No |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Unit system | Not separately recorded | Metric |
| Indicative carbon footprint for new product | Not separately recorded | 0.83 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 0.224 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Dimension series | Not separately recorded | 4CC |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 35 mm |
| Outside diameter | D | 62 mm |
| Bearing width, total | T | 18 mm |
| Shoulder diameter of inner ring | d 1 | ≈ 49.6 mm |
| Width of inner ring | B | 18 mm |
| Width of outer ring | C | 14 mm |
| Chamfer dimension of inner ring | r 1,2 | min. 1 mm |
| Chamfer dimension of outer ring | r 3,4 | min. 1 mm |
| Distance side face to pressure point | a | 14.8 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | max. 41 mm |
| Diameter of shaft abutment | d b | min. 42 mm |
| Diameter of housing abutment | D a | min. 54 mm |
| Diameter of housing abutment | D a | max. 56 mm |
| Diameter of housing abutment | D b | min. 59 mm |
| Minimum width of space required in housing on large side face | C a | min. 4 mm |
| Minimum width of space required in housing on small side face | C b | min. 4 mm |
| Radius of shaft fillet | r a | max. 1 mm |
| Radius of housing fillet | r b | max. 1 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 52.3 kN |
| Basic static load rating | C 0 | 54 kN |
| Fatigue load limit | P u | 5.85 kN |
| Reference speed | Not separately recorded | 8500 r/min |
| Limiting speed | Not separately recorded | 10000 r/min |
| Limiting value | e | 0.46 |
| Calculation factor | Y | 1.3 |
| Calculation factor | Y 0 | 0.7 |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF32007 J2/QSingle row tapered roller bearing |
| 37.4 kN | 49 kN | 8000 rpm | 11000 rpm | 0.225 kg225 g |
| SKF32007 XSingle row tapered roller bearing |
| 52.3 kN | 54 kN | 8500 rpm | 10000 rpm | 0.224 kg224 g |
| SKF32007 X/QSingle row tapered roller bearing |
| 42.9 kN | 54 kN | 8000 rpm | 10000 rpm | 0.224 kg224 g |
| SKF32007 X/VA983Special single row tapered roller bearing |
| 44.1 kN | 56 kN | 7500 rpm | 10000 rpm | 0.228 kg228 g |
| FAG32007-XTapered roller bearing |
| 45.5 kN | 57 kN | 7000 rpm | 11600 rpm | 0.226 kg226 g |
| FAG32007-XDYTapered roller bearing |
| 41.5 kN | 52 kN | 7200 rpm | 11600 rpm | 0.222 kg222 g |
| FAG32007-XDY-XLTapered roller bearing |
| 49.5 kN | 53 kN | 7100 rpm | 14100 rpm | 0.222 kg222 g |
| FAG32007-XDY-XL-P5Tapered roller bearing |
| 49.5 kN | 53 kN | 7100 rpm | 14100 rpm | 0.226 kg226 g |
| FAG32007-X-HTapered roller bearing |
| 43.2 kN | 57 kN | 7000 rpm | 9280 rpm | 0.227 kg227 g |
| TIMKEN32007XTapered roller bearing |
| 56.5 kN | 57.6 kN | — | — | 0.23 kg230 g |
| TIMKEN32007X-99E60Tapered roller bearing |
| 56.5 kN | 57.6 kN | — | — | 0.23 kg230 g |
| TIMKEN32007XM-99E60Tapered roller bearing |
| 56.5 kN | 57.6 kN | — | — | 0.23 kg230 g |
| TIMKEN32007XM-99KA1Tapered roller bearing |
| 56.5 kN | 57.6 kN | — | — | 0.23 kg230 g |
| TIMKEN32007XQTapered roller bearing |
| 56.5 kN | 57.6 kN | — | — | 0.23 kg230 g |
| KOYO32007JRTapered roller bearing |
| 57 kN | 59.4 kN | — | 6200 rpmLimiting Speeds(Grease Lub.): 6200 min-1Limiting Speeds(Oil Lub.): 8200 min-1 | 0.231 kg231 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 32007 J2/Q | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32007 X | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32007 X/Q | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| SKF 32007 X/VA983 | Without | Not recorded | Not recorded | Sheet metal | Not recorded | None |
| FAG 32007-X | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32007-XDY | Not recorded | PN — Normal (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32007-XDY-XL | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32007-XDY-XL-P5 | Not recorded | P5 — Class 5 (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| FAG 32007-X-H | Not recorded | P6X — Class 6X (ISO 492:2023) | Not recorded | Standard — Sheet steel cage, window cage, roller-guided | Not recorded | Not recorded |
| TIMKEN 32007X | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32007X-99E60 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32007XM-99E60 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32007XM-99KA1 | Open | ABMA Class K | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 32007XQ | Open | ABMA Class N | Not recorded | Steel cage | Not recorded | Not recorded |
| KOYO 32007JR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
32007 J2/Q
Single row tapered roller bearing
View full technical record →KOYO32007JR
Tapered roller bearing
View full technical record →FAG32007-X
Tapered roller bearing
View full technical record →TIMKEN32007X
Tapered roller bearing
View full technical record →SKF32007 X
Single row tapered roller bearing
View full technical record →TIMKEN32007X-99E60
Tapered roller bearing
View full technical record →FAG32007-XDY
Tapered roller bearing
View full technical record →FAG32007-XDY-XL
Tapered roller bearing
View full technical record →FAG32007-XDY-XL-P5
Tapered roller bearing
View full technical record →FAG32007-X-H
Tapered roller bearing
View full technical record →TIMKEN32007XM-99E60
Tapered roller bearing
View full technical record →TIMKEN32007XM-99KA1
Tapered roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.