3006 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 3006. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
3006 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 5 recorded variants are listed. A dash means the value is missing, not zero.
Read the original dimensions for 3006
Boundary size alone does not describe every ring, shoulder or assembled unit. These tables retain the recorded manufacturer labels, symbols, units and limits for each complete marking. Expand a record to check its detailed measurements.
Important: an approximate value, a minimum or a maximum keeps that qualifier. These reference extracts are not CAD drawings, fit recommendations or replacement approvals.
INA 3006 — 12 dimension fields
Angular contact ball bearing. Source: Schaeffler medias — INA; recorded snapshot 2026-09-02.
Use the complete designation shown here. A seal, cage, clearance or precision suffix can matter even when nominal boundary dimensions match.
Minimum and maximum mounting dimensions are limits, not nominal bearing dimensions. Check shaft/housing shoulders and fillets against the current drawing before designing a seat.
Bearing and component measurements
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Bore Diameter (D) | Not supplied separately | 30 mm |
| Outside Diameter (D) | Not supplied separately | 55 mm |
| Width (B) | Not supplied separately | 19 mm |
| Caliber Diameter Outer Ring (D2) | Not supplied separately | 49.05 mm |
| Caliber Diameter Inner Ring (D1) | Not supplied separately | 35.68 mm |
| Distance Between The Apexes Of The Pressure Cones (A) | Not supplied separately | 27.4 mm |
Mounting limits and abutments
| Measurement | Source symbol | Recorded value |
|---|---|---|
| Minimum Diameter Shaft Shoulder (Da Min) | Not supplied separately | 34.6 mm |
| Shoulder Diameter Inner Ring (D1) | Not supplied separately | 37.7 mm |
| Maximum Diameter Of Housing Shoulder (Da Max) | Not supplied separately | 50.4 mm |
| Minimum Chamfer Dimension (Rmin) | Not supplied separately | 1 mm |
| Maximum Fillet Radius (Ra Max) | Not supplied separately | 1 mm |
| Shoulder Diameter Outer Ring (D1) | Not supplied separately | 46.92 mm |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| INA3006Angular contact ball bearing |
| 19.9 kN | 15.4 kN | 10100 rpm | 13500 rpm | 0.16 kg160 g |
| INA3006-2RSAngular contact ball bearing |
| 19.9 kN | 15.4 kN | — | 7400 rpm | 0.167 kg167 g |
| INA3006-2RS-C3Angular contact ball bearing |
| 19.9 kN | 15.4 kN | — | 7400 rpm | 0.167 kg167 g |
| INA3006-2ZAngular contact ball bearing |
| 19.9 kN | 15.4 kN | 10100 rpm | 10100 rpm | 0.168 kg168 g |
| INA3006-C3Angular contact ball bearing |
| 19.9 kN | 15.4 kN | 10100 rpm | 13500 rpm | 0.162 kg162 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| INA 3006 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA 3006-2RS | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA 3006-2RS-C3 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA 3006-2Z | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| INA 3006-C3 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
3006
Angular contact ball bearing
View full technical record →INA3006-2RS
Angular contact ball bearing
View full technical record →INA3006-2RS-C3
Angular contact ball bearing
View full technical record →INA3006-2Z
Angular contact ball bearing
View full technical record →INA3006-C3
Angular contact ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.