29322 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 29322. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
29322 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 4 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 29322
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 29322 E — 34 recorded parameters
Spherical roller thrust bearing with stamped steel cage
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 110.0 mm |
| Outside diameter | Not separately recorded | 190.0 mm |
| Height | Not separately recorded | 48.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 610.0 kN |
| Basic static load rating | Not separately recorded | 1730.0 kN |
| Reference speed | Not separately recorded | 1900.0 r/min |
| Limiting speed | Not separately recorded | 3200.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Tolerance class | Not separately recorded | Normal |
| Indicative carbon footprint for new product | Not separately recorded | 19.6 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 5.3 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 110 mm |
| Outside diameter | D | 190 mm |
| Height | H | 48 mm |
| Outside diameter of shaft washer end side face | d 1 | ≈ 171 mm |
| Shoulder diameter outer ring | D 1 | ≈ 140 mm |
| Width shaft washer or length of shaft washer bore diameter that fits on shaft (bearings with a stamped steel cage) | B | 30.3 mm |
| Height shaft washer + cage | B 1 | 41.7 mm |
| Height housing washer | C | 24.8 mm |
| Distance from shaft washer end side face to pressure point | s | 63.8 mm |
| Chamfer dimension shaft washer | r 1,2 | min. 2 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 145 mm |
| Abutment diameter of spacer ring | d b1 | max. 117 mm |
| Outside diameter of spacer ring | d b2 | max. 117 mm |
| Diameter of housing abutment | D a | max. 164 mm |
| Fillet radius | r a | max. 2 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | C | 610 kN |
| Basic static load rating | C 0 | 1730 kN |
| Fatigue load limit | P u | 204 kN |
| Reference speed | Not separately recorded | 1900 r/min |
| Limiting speed | Not separately recorded | 3200 r/min |
| Minimum axial load factor | A | 0.28 |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF29322 ESpherical roller thrust bearing with stamped steel cage |
| 610 kN | 1730 kN | 1900 rpm | 3200 rpm | 5.3 kg5300 g |
| FAG29322-E1-XLAxial spherical roller bearing |
| — | — | 1840 rpm | 3750 rpm | 5.06 kg5060 g |
| FAG29322-E1-XL-N1Axial spherical roller bearing |
| — | — | 1830 rpm | 3750 rpm | 5.123 kg5123 g |
| KOYO29322RAxial spherical roller bearing |
| — | — | — | 2000 rpmLimiting Speeds(Oil Lub.): 2000 min-1 | 5.67 kg5670 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 29322 E | Not recorded | Not recorded | Not recorded | Sheet metal | Not recorded | Not recorded |
| FAG 29322-E1-XL | Not recorded | Not recorded | Not recorded | JP — Sheet metal cage | Not recorded | Not recorded |
| FAG 29322-E1-XL-N1 | Not recorded | Not recorded | Not recorded | JP — Sheet metal cage | Not recorded | Not recorded |
| KOYO 29322R | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
29322 E
Spherical roller thrust bearing with stamped steel cage
View full technical record →FAG29322-E1-XL
Axial spherical roller bearing
View full technical record →FAG29322-E1-XL-N1
Axial spherical roller bearing
View full technical record →KOYO29322R
Axial spherical roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.