Find · understand · compare
22220 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 22220. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
22220 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 53 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 22220
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 22220 EK/C3 — 53 recorded parameters
Spherical roller bearing with tapered bore and relubrication features
Reference: SKF product catalogue; source snapshot 2026-09-02.
SKF 22220 EK/C3 initial radial clearance: 110–140 µm (0.110–0.140 mm). The recorded clearance class is C3, bore diameter d = 100 mm, and bore taper is 1:12. These numbers belong to this full designation, not every 22220 variant.
Why this interval: SKF Spherical roller bearings, publication 18406 EN, Table 5 (printed page 13), places this tapered bore in 80 < d ≤ 100 mm. The exact product record and the table agree. A bore exactly at the upper boundary stays in this row; the cylindrical-bore table is not interchangeable with it.
Read this as clearance before installation, with no measuring load applied. It is not a required residual gap after driving the bearing up its taper, a shaft fit tolerance, an axial endplay value, or an operating-clearance target.
For mounting, use the procedure for the complete bearing and shaft or sleeve arrangement. Initial clearance alone cannot determine a locknut angle or drive-up distance. Fits and ring temperatures can change the remaining clearance; do not set the assembly to the unmounted maximum.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 100.0 mm |
| Outside diameter | Not separately recorded | 180.0 mm |
| Width | Not separately recorded | 46.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 433.0 kN |
| Basic static load rating | Not separately recorded | 490.0 kN |
| Reference speed | Not separately recorded | 3400.0 r/min |
| Limiting speed | Not separately recorded | 4500.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Number of rows | Not separately recorded | 2 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Tapered 1:12 |
| Cage | Not separately recorded | Sheet metal |
| Radial internal clearance | Not separately recorded | C3 |
| Tolerance class for dimensions | Not separately recorded | Normal |
| Tolerance class for run-out | Not separately recorded | P5 |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | With |
| Candidate for remanufacturing | Not separately recorded | Yes |
| Indicative carbon footprint for new product | Not separately recorded | 17.8 kg CO 2 e |
| Indicative carbon footprint for remanufactured product | Not separately recorded | 5.9 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 4.82 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore type | Not separately recorded | Tapered 1:12 |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 100 mm |
| Deviation limits of tapered slope | t ΔSL | 0 to 0.035 mm |
| Outside diameter | D | 180 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.025 to 0 mm |
| Width | B | 46 mm |
| Deviation limits of ring width | t ΔBs | -0.08 to 0 mm |
| Shoulder diameter of inner ring | d 2 | ≈ 118 mm |
| Shoulder/recess diameter of outer ring | D 1 | ≈ 159 mm |
| Width of lubrication groove | b | 8.3 mm |
| Diameter of lubrication hole | K | 4.5 mm |
| Chamfer dimension | r 1,2 | min. 2.1 mm |
| ISO tolerance class for dimensions | Not separately recorded | Normal |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of housing abutment | D a | max. 168 mm |
| Radius of fillet | r a | max. 2 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 433 kN |
| Basic static load rating | C 0 | 490 kN |
| Fatigue load limit | P u | 49 kN |
| Reference speed | Not separately recorded | 3400 r/min |
| Limiting speed | Not separately recorded | 4500 r/min |
| Limiting value | e | 0.24 |
| Calculation factor | Y 1 | 2.8 |
| Calculation factor | Y 2 | 4.2 |
| Calculation factor | Y 0 | 2.8 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 6 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 9 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 13 µm |
| Perpendicularity of outer ring outside surface | t SD | 5 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
Engineering — Radial internal clearance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum initial clearance | Not separately recorded | 110 µm |
| Maximum initial clearance | Not separately recorded | 140 µm |
SKF 22220 EK — 54 recorded parameters
Spherical roller bearing with tapered bore and relubrication features
Reference: SKF product catalogue; source snapshot 2026-09-02.
SKF 22220 EK initial radial clearance: 80–110 µm (0.080–0.110 mm). The recorded clearance class is CN, bore diameter d = 100 mm, and bore taper is 1:12. These numbers belong to this full designation, not every 22220 variant.
Why this interval: SKF Spherical roller bearings, publication 18406 EN, Table 5 (printed page 13), places this tapered bore in 80 < d ≤ 100 mm. The exact product record and the table agree. A bore exactly at the upper boundary stays in this row; the cylindrical-bore table is not interchangeable with it.
Read this as clearance before installation, with no measuring load applied. It is not a required residual gap after driving the bearing up its taper, a shaft fit tolerance, an axial endplay value, or an operating-clearance target.
For mounting, use the procedure for the complete bearing and shaft or sleeve arrangement. Initial clearance alone cannot determine a locknut angle or drive-up distance. Fits and ring temperatures can change the remaining clearance; do not set the assembly to the unmounted maximum.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 100.0 mm |
| Outside diameter | Not separately recorded | 180.0 mm |
| Width | Not separately recorded | 46.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 433.0 kN |
| Basic static load rating | Not separately recorded | 490.0 kN |
| Reference speed | Not separately recorded | 3400.0 r/min |
| Limiting speed | Not separately recorded | 4500.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Number of rows | Not separately recorded | 2 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Tapered 1:12 |
| Cage | Not separately recorded | Sheet metal |
| Radial internal clearance | Not separately recorded | CN |
| Tolerance class for dimensions | Not separately recorded | Normal |
| Tolerance class for run-out | Not separately recorded | P5 |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | With |
| Candidate for remanufacturing | Not separately recorded | Yes |
| Indicative carbon footprint for new product | Not separately recorded | 17.5 kg CO 2 e |
| Indicative carbon footprint for remanufactured product | Not separately recorded | 5.8 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 4.74 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore type | Not separately recorded | Tapered 1:12 |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 100 mm |
| Deviation limits of tapered slope | t ΔSL | 0 to 0.035 mm |
| Outside diameter | D | 180 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.025 to 0 mm |
| Width | B | 46 mm |
| Deviation limits of ring width | t ΔBs | -0.08 to 0 mm |
| Shoulder diameter of inner ring | d 2 | ≈ 118 mm |
| Shoulder/recess diameter of outer ring | D 1 | ≈ 159 mm |
| Width of lubrication groove | b | 8.3 mm |
| Diameter of lubrication hole | K | 4.5 mm |
| Chamfer dimension | r 1,2 | min. 2.1 mm |
| ISO tolerance class for dimensions | Not separately recorded | Normal |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of housing abutment | D a | max. 168 mm |
| Radius of fillet | r a | max. 2 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 433 kN |
| Basic static load rating | C 0 | 490 kN |
| Fatigue load limit | P u | 49 kN |
| Reference speed | Not separately recorded | 3400 r/min |
| Limiting speed | Not separately recorded | 4500 r/min |
| Limiting value | e | 0.24 |
| Calculation factor | Y 1 | 2.8 |
| Calculation factor | Y 2 | 4.2 |
| Calculation factor | Y 0 | 2.8 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 6 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 9 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 13 µm |
| Perpendicularity of outer ring outside surface | t SD | 5 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
Engineering — Radial internal clearance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum initial clearance | Not separately recorded | 80 µm |
| Maximum initial clearance | Not separately recorded | 110 µm |
Engineering — Mounting information
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Recommended tightening angle for lock nut | α | 150 ° |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF22220/C3W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 351 kN | 465 kN | — | 450 rpm | 4.8 kg4800 g |
| SKF22220/C4W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 351 kN | 465 kN | — | 450 rpm | 4.85 kg4850 g |
| SKF22220 ESpherical roller bearing with relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.95 kg4950 g |
| SKF22220 E/C2Spherical roller bearing with relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.97 kg4970 g |
| SKF22220 E/C3Spherical roller bearing with relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.85 kg4850 g |
| SKF22220 E/C4Spherical roller bearing with relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.85 kg4850 g |
| SKF22220 EKSpherical roller bearing with tapered bore and relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.74 kg4740 g |
| SKF22220 EK/C3Spherical roller bearing with tapered bore and relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.82 kg4820 g |
| SKF22220 EK/C4Spherical roller bearing with tapered bore and relubrication features |
| 433 kN | 490 kN | 3400 rpm | 4500 rpm | 4.85 kg4850 g |
| SKF22220 K/C3W33VA9A1Spherical roller bearing for low-speed applications, with tapered bore and relubrication features |
| 351 kN | 475 kN | — | 450 rpm | 4.75 kg4750 g |
| SKF22220 K/W33VA9A1Spherical roller bearing for low-speed applications, with tapered bore and relubrication features |
| 351 kN | 465 kN | — | 450 rpm | 4.75 kg4750 g |
| SKF22220/W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 351 kN | 465 kN | — | 450 rpm | 4.9 kg4900 g |
| FAG22220-E1A-XL-K-MSpherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.834 kg4834 g |
| FAG22220-E1A-XL-K-M-C3Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.939 kg4939 g |
| FAG22220-E1A-XL-K-M-C4Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.843 kg4843 g |
| FAG22220-E1A-XL-MSpherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.931 kg4931 g |
| FAG22220-E1A-XL-M-C2Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.941 kg4941 g |
| FAG22220-E1A-XL-M-C3Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.941 kg4941 g |
| FAG22220-E1A-XL-M-C4Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.921 kg4921 g |
| FAG22220-E1-XLSpherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.962 kg4962 g |
| FAG22220-E1-XL-C2Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.95 kg4950 g |
| FAG22220-E1-XL-C3Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.962 kg4962 g |
| FAG22220-E1-XL-C4Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.938 kg4938 g |
| FAG22220-E1-XL-C5Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.936 kg4936 g |
| FAG22220-E1-XL-KSpherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.839 kg4839 g |
| FAG22220-E1-XL-K-C2Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.91 kg4910 g |
| FAG22220-E1-XL-K-C3Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.86 kg4860 g |
| FAG22220-E1-XL-K-C4Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.833 kg4833 g |
| FAG22220-E1-XL-K-C5Spherical Roller Bearing |
| 430 kN | 475 kN | 3150 rpm | 4550 rpm | 4.84 kg4840 g |
| TIMKEN22220EJSpherical roller bearing |
| 435 kN | 502 kN | — | — | 4.99 kg4990 g |
| TIMKEN22220EJW33Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.94 kg4940 g |
| TIMKEN22220EJW33C2Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.94 kg4940 g |
| TIMKEN22220EJW33C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.94 kg4940 g |
| TIMKEN22220EJW33C3SLASpherical roller bearing |
| 435 kN | 502 kN | — | — | 5.02 kg5020 g |
| TIMKEN22220EJW33C4Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.94 kg4940 g |
| TIMKEN22220EJW33W97AC4Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.94 kg4940 g |
| TIMKEN22220EMW33Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.99 kg4990 g |
| TIMKEN22220EMW33C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.99 kg4990 g |
| TIMKEN22220KEJW33Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.82 kg4820 g |
| TIMKEN22220KEJW33C2Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.83 kg4830 g |
| TIMKEN22220KEJW33C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.82 kg4820 g |
| TIMKEN22220KEJW33C4Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.83 kg4830 g |
| TIMKEN22220KEJW33S2C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.83 kg4830 g |
| TIMKEN22220KEJW841C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.83 kg4830 g |
| TIMKEN22220KEMW33Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.87 kg4870 g |
| TIMKEN22220KEMW33C3Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.87 kg4870 g |
| TIMKEN22220KEMW33C4Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.87 kg4870 g |
| TIMKEN22220KEMW33W800C4Spherical roller bearing |
| 435 kN | 502 kN | — | — | 4.87 kg4870 g |
| NSK22220EAE4Spherical roller bearing |
| 455 kN | 490 kN | — | — | 4.84 kg4840 g |
| NSK22220EAKE4Spherical roller bearing |
| 455 kN | 490 kN | — | — | — |
| KOYO22220RHRSpherical roller bearing |
| 470 kN | 481 kN | — | 2600 rpmLimiting Speeds(Grease Lub.): 2600 min-1Limiting Speeds(Oil Lub.): 3400 min-1 | 5.11 kg5110 g |
| KOYO22220RZK+AHX320Spherical roller bearing |
| 470 kN | 481 kN | — | 2600 rpmLimiting Speeds(Grease Lub.): 2600 min-1Limiting Speeds(Oil Lub.): 3400 min-1 | 5.58 kg5580 g |
| KOYO22220RZK+H320XSpherical roller bearing |
| 470 kN | 481 kN | — | 2600 rpmLimiting Speeds(Grease Lub.): 2600 min-1Limiting Speeds(Oil Lub.): 3400 min-1 | 6.8 kg6800 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 22220/C3W33VA9A1 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22220/C4W33VA9A1 | Without | Not recorded | C4 | Sheet metal | Not recorded | None |
| SKF 22220 E | Without | Normal | CN | Sheet metal | Not recorded | None |
| SKF 22220 E/C2 | Without | Not recorded | C2 | Sheet metal | Not recorded | None |
| SKF 22220 E/C3 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22220 E/C4 | Without | Not recorded | C4 | Sheet metal | Not recorded | None |
| SKF 22220 EK | Without | Normal | CN | Sheet metal | Not recorded | None |
| SKF 22220 EK/C3 | Without | Normal | C3 | Sheet metal | Not recorded | None |
| SKF 22220 EK/C4 | Without | Normal | C4 | Sheet metal | Not recorded | None |
| SKF 22220 K/C3W33VA9A1 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22220 K/W33VA9A1 | Without | Not recorded | CN | Sheet metal | Not recorded | None |
| SKF 22220/W33VA9A1 | Without | Not recorded | CN | Sheet metal | Not recorded | None |
| FAG 22220-E1A-XL-K-M | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-K-M-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-K-M-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-M | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-M-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-M-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1A-XL-M-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | M — Brass Cage | Not recorded | Not recorded |
| FAG 22220-E1-XL | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-C5 | Not recorded | Not recorded | Not recorded | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-K | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-K-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-K-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-K-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22220-E1-XL-K-C5 | Not recorded | Not recorded | Not recorded | JPA — Sheet metal cage | Not recorded | Not recorded |
| TIMKEN 22220EJ | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33C2 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33C3SLA | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EJW33W97AC4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220EMW33 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22220EMW33C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW33 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW33C2 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW33C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW33C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW33S2C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEJW841C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22220KEMW33 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22220KEMW33C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22220KEMW33C4 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22220KEMW33W800C4 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| NSK 22220EAE4 | Not recorded | Not recorded | CN | Pressed steel | Not recorded | Not recorded |
| NSK 22220EAKE4 | Not recorded | Not recorded | CN | Pressed steel | Not recorded | Not recorded |
| KOYO 22220RHR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 22220RZK+AHX320 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 22220RZK+H320X | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
22220/C3W33VA9A1
Spherical roller bearing for low-speed applications, with relubrication features
View full technical record →SKF22220/C4W33VA9A1
Spherical roller bearing for low-speed applications, with relubrication features
View full technical record →SKF22220 E
Spherical roller bearing with relubrication features
View full technical record →FAG22220-E1A-XL-K-M
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-K-M-C3
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-K-M-C4
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-M
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-M-C2
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-M-C3
Spherical Roller Bearing
View full technical record →FAG22220-E1A-XL-M-C4
Spherical Roller Bearing
View full technical record →FAG22220-E1-XL
Spherical Roller Bearing
View full technical record →FAG22220-E1-XL-C2
Spherical Roller Bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.