Find · understand · compare
22215 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 22215. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
22215 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 45 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 22215
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 22215 EK — 52 recorded parameters
Spherical roller bearing with tapered bore and relubrication features
Reference: SKF product catalogue; source snapshot 2026-09-02.
SKF 22215 EK initial radial clearance: 70–95 µm (0.070–0.095 mm). The recorded clearance class is CN, bore diameter d = 75 mm, and bore taper is 1:12. These numbers belong to this full designation, not every 22215 variant.
Why this interval: SKF Spherical roller bearings, publication 18406 EN, Table 5 (printed page 13), places this tapered bore in 65 < d ≤ 80 mm. The exact product record and the table agree. A bore exactly at the upper boundary stays in this row; the cylindrical-bore table is not interchangeable with it.
Read this as clearance before installation, with no measuring load applied. It is not a required residual gap after driving the bearing up its taper, a shaft fit tolerance, an axial endplay value, or an operating-clearance target.
For mounting, use the procedure for the complete bearing and shaft or sleeve arrangement. Initial clearance alone cannot determine a locknut angle or drive-up distance. Fits and ring temperatures can change the remaining clearance; do not set the assembly to the unmounted maximum.
Keep total assembly width distinct from inner- and outer-ring widths. The same nominal bore does not establish a matching cup/cone set.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 75.0 mm |
| Outside diameter | Not separately recorded | 130.0 mm |
| Width | Not separately recorded | 31.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 217.0 kN |
| Basic static load rating | Not separately recorded | 240.0 kN |
| Reference speed | Not separately recorded | 4800.0 r/min |
| Limiting speed | Not separately recorded | 6300.0 r/min |
| SKF performance class | Not separately recorded | SKF Explorer |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Number of rows | Not separately recorded | 2 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Tapered 1:12 |
| Cage | Not separately recorded | Sheet metal |
| Radial internal clearance | Not separately recorded | CN |
| Tolerance class for dimensions | Not separately recorded | Normal |
| Tolerance class for run-out | Not separately recorded | P5 |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | With |
| Indicative carbon footprint for new product | Not separately recorded | 6.1 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 1.65 kg |
Engineering — Engineering specifications
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore type | Not separately recorded | Tapered 1:12 |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 75 mm |
| Deviation limits of tapered slope | t ΔSL | 0 to 0.03 mm |
| Outside diameter | D | 130 mm |
| Deviation limits of mid-range outside diameter | t ΔDmp | -0.018 to 0 mm |
| Width | B | 31 mm |
| Deviation limits of ring width | t ΔBs | -0.06 to 0 mm |
| Shoulder diameter of inner ring | d 2 | ≈ 87.8 mm |
| Shoulder/recess diameter of outer ring | D 1 | ≈ 115 mm |
| Width of lubrication groove | b | 6 mm |
| Diameter of lubrication hole | K | 3 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
| ISO tolerance class for dimensions | Not separately recorded | Normal |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of housing abutment | D a | max. 121 mm |
| Radius of fillet | r a | max. 1.5 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| SKF performance class | Not separately recorded | SKF Explorer |
| Basic dynamic load rating | C | 217 kN |
| Basic static load rating | C 0 | 240 kN |
| Fatigue load limit | P u | 26.5 kN |
| Reference speed | Not separately recorded | 4800 r/min |
| Limiting speed | Not separately recorded | 6300 r/min |
| Limiting value | e | 0.22 |
| Calculation factor | Y 1 | 3 |
| Calculation factor | Y 2 | 4.6 |
| Calculation factor | Y 0 | 2.8 |
Engineering — Tolerances of run-out
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Range of section height at inner ring of assembled bearing | t Kia | 5 µm |
| Maximum run-out of inner ring side face to the bore | t Sd | 8 µm |
| Range of section height at outer ring of assembled bearing | t Kea | 11 µm |
| Perpendicularity of outer ring outside surface | t SD | 5 µm |
| ISO tolerance class for geometrical tolerances | Not separately recorded | P5 |
Engineering — Radial internal clearance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Minimum initial clearance | Not separately recorded | 70 µm |
| Maximum initial clearance | Not separately recorded | 95 µm |
Engineering — Mounting information
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Recommended tightening angle for lock nut | α | 130 ° |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF22215/C3W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 176 kN | 232 kN | — | 630 rpm | 1.65 kg1650 g |
| SKF22215/C4W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 176 kN | 232 kN | — | 630 rpm | 1.6 kg1600 g |
| SKF22215 ESpherical roller bearing with relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.68 kg1680 g |
| SKF22215 E/C2Spherical roller bearing with relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.68 kg1680 g |
| SKF22215 E/C3Spherical roller bearing with relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.68 kg1680 g |
| SKF22215 E/C4Spherical roller bearing with relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.68 kg1680 g |
| SKF22215 E/C5Spherical roller bearing with relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.68 kg1680 g |
| SKF22215 EKSpherical roller bearing with tapered bore and relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.65 kg1650 g |
| SKF22215 EK/C3Spherical roller bearing with tapered bore and relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.65 kg1650 g |
| SKF22215 EK/C4Spherical roller bearing with tapered bore and relubrication features |
| 217 kN | 240 kN | 4800 rpm | 6300 rpm | 1.65 kg1650 g |
| SKF22215 K/C3W33VA9A1Spherical roller bearing for low-speed applications, with tapered bore and relubrication features |
| 176 kN | 232 kN | — | 630 rpm | 1.65 kg1650 g |
| SKF22215 K/W33VA9A1Spherical roller bearing for low-speed applications, with tapered bore and relubrication features |
| 176 kN | 232 kN | — | 630 rpm | 1.65 kg1650 g |
| SKF22215/W33VA9A1Spherical roller bearing for low-speed applications, with relubrication features |
| 176 kN | 232 kN | — | 630 rpm | 1.65 kg1650 g |
| FAG22215-E1A-XL-K-MSpherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.637 kg1637 g |
| FAG22215-E1A-XL-K-M-C3Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.635 kg1635 g |
| FAG22215-E1A-XL-MSpherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.69 kg1690 g |
| FAG22215-E1A-XL-M-C2Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.66 kg1660 g |
| FAG22215-E1A-XL-M-C3Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.669 kg1669 g |
| FAG22215-E1A-XL-M-C4Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.66 kg1660 g |
| FAG22215-E1-XLSpherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.668 kg1668 g |
| FAG22215-E1-XL-C2Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.61 kg1610 g |
| FAG22215-E1-XL-C3Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.68 kg1680 g |
| FAG22215-E1-XL-C4Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.61 kg1610 g |
| FAG22215-E1-XL-C5Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.61 kg1610 g |
| FAG22215-E1-XL-KSpherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.676 kg1676 g |
| FAG22215-E1-XL-K-C2Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.55 kg1550 g |
| FAG22215-E1-XL-K-C3Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.642 kg1642 g |
| FAG22215-E1-XL-K-C4Spherical Roller Bearing |
| 216 kN | 237 kN | 3700 rpm | 6500 rpm | 1.634 kg1634 g |
| TIMKEN22215EJW33Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.65 kg1650 g |
| TIMKEN22215EJW33C2Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.65 kg1650 g |
| TIMKEN22215EJW33C3Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.65 kg1650 g |
| TIMKEN22215EJW33C4Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.65 kg1650 g |
| TIMKEN22215EJW33S3C4Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.65 kg1650 g |
| TIMKEN22215EJW841C3Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.67 kg1670 g |
| TIMKEN22215EMW33Spherical roller bearing |
| 214 kN | 228 kN | — | — | 1.64 kg1640 g |
| TIMKEN22215EMW33C3Spherical roller bearing |
| 214 kN | 228 kN | — | — | 1.64 kg1640 g |
| TIMKEN22215KEJW33Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.61 kg1610 g |
| TIMKEN22215KEJW33C3Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.61 kg1610 g |
| TIMKEN22215KEJW33C4Spherical roller bearing |
| 222 kN | 240 kN | — | — | 1.61 kg1610 g |
| TIMKEN22215KEMW33C3Spherical roller bearing |
| 214 kN | 228 kN | — | — | 1.6 kg1600 g |
| NSK22215EAE4Spherical roller bearing |
| 238 kN | 244 kN | — | — | 1.64 kg1640 g |
| NSK22215EAKE4Spherical roller bearing |
| 238 kN | 244 kN | — | — | — |
| KOYO22215RZSpherical roller bearing |
| 241 kN | 236 kN | — | 3600 rpmLimiting Speeds(Grease Lub.): 3600 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 1.73 kg1730 g |
| KOYO22215RZK+AH315Spherical roller bearing |
| 241 kN | 236 kN | — | 3600 rpmLimiting Speeds(Grease Lub.): 3600 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 2.01 kg2010 g |
| KOYO22215RZK+H315XSpherical roller bearing |
| 241 kN | 236 kN | — | 3600 rpmLimiting Speeds(Grease Lub.): 3600 min-1Limiting Speeds(Oil Lub.): 4700 min-1 | 2.58 kg2580 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 22215/C3W33VA9A1 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22215/C4W33VA9A1 | Without | Not recorded | C4 | Sheet metal | Not recorded | None |
| SKF 22215 E | Without | Normal | CN | Sheet metal | Not recorded | None |
| SKF 22215 E/C2 | Without | Not recorded | C2 | Sheet metal | Not recorded | None |
| SKF 22215 E/C3 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22215 E/C4 | Without | Not recorded | C4 | Sheet metal | Not recorded | None |
| SKF 22215 E/C5 | Without | Not recorded | C5 | Sheet metal | Not recorded | None |
| SKF 22215 EK | Without | Normal | CN | Sheet metal | Not recorded | None |
| SKF 22215 EK/C3 | Without | Normal | C3 | Sheet metal | Not recorded | None |
| SKF 22215 EK/C4 | Without | Normal | C4 | Sheet metal | Not recorded | None |
| SKF 22215 K/C3W33VA9A1 | Without | Not recorded | C3 | Sheet metal | Not recorded | None |
| SKF 22215 K/W33VA9A1 | Without | Not recorded | CN | Sheet metal | Not recorded | None |
| SKF 22215/W33VA9A1 | Without | Not recorded | CN | Sheet metal | Not recorded | None |
| FAG 22215-E1A-XL-K-M | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1A-XL-K-M-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1A-XL-M | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1A-XL-M-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1A-XL-M-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1A-XL-M-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | M — Brass Cage | Not recorded | Not recorded |
| FAG 22215-E1-XL | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-C5 | Not recorded | Not recorded | Not recorded | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-K | Not recorded | Not recorded | CN (Group N) — Normal internal clearance | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-K-C2 | Not recorded | Not recorded | C2 (Group 2) — Internal clearance smaller than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-K-C3 | Not recorded | Not recorded | C3 (Group 3) — Internal clearance larger than CN | JPA — Sheet metal cage | Not recorded | Not recorded |
| FAG 22215-E1-XL-K-C4 | Not recorded | Not recorded | C4 (Group 4) — Internal clearance larger than C3 | JPA — Sheet metal cage | Not recorded | Not recorded |
| TIMKEN 22215EJW33 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EJW33C2 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EJW33C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EJW33C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EJW33S3C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EJW841C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215EMW33 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22215EMW33C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| TIMKEN 22215KEJW33 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215KEJW33C3 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215KEJW33C4 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 22215KEMW33C3 | Open | Not recorded | Not recorded | Brass cage | Not recorded | Not recorded |
| NSK 22215EAE4 | Not recorded | Not recorded | CN | Pressed steel | Not recorded | Not recorded |
| NSK 22215EAKE4 | Not recorded | Not recorded | CN | Pressed steel | Not recorded | Not recorded |
| KOYO 22215RZ | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 22215RZK+AH315 | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| KOYO 22215RZK+H315X | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
SKF
22215/C3W33VA9A1
Spherical roller bearing for low-speed applications, with relubrication features
View full technical record →SKF22215/C4W33VA9A1
Spherical roller bearing for low-speed applications, with relubrication features
View full technical record →SKF22215 E
Spherical roller bearing with relubrication features
View full technical record →FAG22215-E1A-XL-K-M
Spherical Roller Bearing
View full technical record →FAG22215-E1A-XL-K-M-C3
Spherical Roller Bearing
View full technical record →FAG22215-E1A-XL-M
Spherical Roller Bearing
View full technical record →FAG22215-E1A-XL-M-C2
Spherical Roller Bearing
View full technical record →FAG22215-E1A-XL-M-C3
Spherical Roller Bearing
View full technical record →FAG22215-E1A-XL-M-C4
Spherical Roller Bearing
View full technical record →FAG22215-E1-XL
Spherical Roller Bearing
View full technical record →FAG22215-E1-XL-C2
Spherical Roller Bearing
View full technical record →FAG22215-E1-XL-C3
Spherical Roller Bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.